EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Guidance on DSP and DAC IC’s To Use
Hi, I am building some 3-way Active Speakers, and I have designed the analogue filter stage, and in implementing the PCB design, the size of the PCB is large. After searching on DSP audio boards there
-
Dealing complex numbers in sigma studio
I'm currently using EVAL - ADAU1467 sigmaDSP which can be programmed through sigma studio ( I'm using Ver. 4.2 / 64 bit OS). As per my applications, I have to use complex number based calculations ( t
-
RE: adau1452 for Echo Cancelling
I need to design an echo cancelling circuit for a speakerphone system.the hardware platform is ADAU145,I need help from you.Thanks. My Email: li.fa@bohui.com.cn Edit Notes Renamed the subject to the p
-
Estimating frequency of a signal in sigmaDSP
I'm working on EVAL-ADAU1467Z based SigmaDSP. Due to my application requirement, I have to estimate the frequency of the incoming signal (specifically audio signal) at every instant of real time. i.e.
-
difference between 1772 and 1777?
Hello! Currently trying to figure out which eval board to get and it's between the 1772 and 1777. What's the difference between these two platforms? From the datasheets I see that the 1777 allows a hi
-
use of GPIO as index input for 1701 vs 1452
Hello, I have successfully used GPIO input to feed the index input of MUX block for ADAU1452. But there is different story with ADAU1701. The output format of GPIO block is not compatible with input f
-
Calculation Of Noise correlation matrix in SIgmaDSPs.
I'm new to sigmaDSPs and working on EVAL-ADAU 1467Z audio signal DSP board,currently. In such a scenario, I have to construct a Noise Auto - correlation matrix present in the input mixture of audio si
-
公式算出虑波器系数a1,a2刚好和SigmalStudio捕捉到结果相反
1.下图,左边是SigmalStudio里虑波器的参数设置,右边是单片机的计算设置 2.然后,可以在SigmalStudio的捕捉到格项系数 3.那么问题如下: 请教下,问题出在哪里?是以哪个的结果为准呢?谢谢 Mid EQ.zipEQ_calculation.zip
-
ADAU1702 - TDM mode configuration.
Hi, I'm having difficulties configuring the TDM mode on my ADAU1702, and I'm running out of ideas. I am trying to configure the TDM in to send 2 samples to the 4 DACs and despite my best efforts it's
-
What is the Adjustable Low Pass Filter "Step" mean?
Hello guys, Can someone help me to understand what is the " Adjustable LPF " function block which has one parameter call "step", what is this actually work at? I am using ADC to adjust the Low pass fr
-
ADAU1701 Simultaneous use of serial 1 data and built in ADC
Hello, I'm currently working on a project where I like to use the built in audio ADC's and Input_Sdata_in1 simultaneously But when I switch MP4 to Input_LRCLK_in and MP5 to Bclk_In in order to slave t
-
ADAU144x Pseudo-random square wave?
I have a possibly strange requirement for a bench test that I am developing. Currently I am switching between two signal lines using an index-selectable MUX. The index is created using a square wave s
-
Flash programmer limitation of ADAU1452
Dear Support team, When I write big data to Flash, Flash programmer show verify error. But, the data may be written normaly to flash. Becase the data can be playbacked by WAB player. Is it bug or limi
-
ADAU1452. Instruction per sample, how calculate?
Hi. I building the project with many audio channels (14 channels amplifier). For this project I used ADAU1452 + STM32 microcontroller I used 96kHz sample rate. Each channel have independent filters (I
-
Accessing the other audio input/output ports of EVAL - ADAU1467Z.
So, currently I'm using EVAL-ADAU1467Z board to carry out my audio signal processing project. As per the project specifications, I need multiple inputs to be processed by the board. So, the board has
-
Building custom blocks in sigma studio for sigmadsps.
I'm currently working on building a acoustic beam former with 4 audio inputs based on my own algorithm. So, I have purchased EVAL-ADAU1467Z board for implementing the same. This is a sigmaDSP that can
-
Calculating Filter Coefficients In DSP
Hello! I'm searching for info about change parameters for filter over SPI. I fully understand principle - I have created communication between main microcontroller connected to DSP development board S
-
怎样用SS里的公式去真正推算EQ参数?
想向ADI的工程师请教个问题。在上位机要通过MCU去设置EQ的参数,如下: https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/filters/general2ndorder 或SigmalStudio的help 都有下面的公式:那么,我想请教,就这个例子而言,是如何利用下面的公式推算出来的呢?很希望能指教一下。
-
Can't make Index Selectable Multiplexer work!
I know I'm neglecting something silly, but I just can't make one of these infernal devices switch. I need to select between two DC levels with a logic 1 or 0. I've used ABCD blocks before with no prob
-
sigmastudio adaptive filters
Hello: Complete noob to sigmastudio here, wondering if anyone can tell me how to display/read the coefficients of an adaptive filter (e.g., NLMS). Thanks, HH
-
ADAU1467 - CORE_STATUS = 0
I recently received our new digital audio board which is equipped with an ADAU1467. We have an external master clock signal running at 24.576MHz, 3.9V pk-pk. Verified that we have the master clock on
-
Need help implementing multiplexer using external switch
Hello, I have a custom ADAU1701 board which is working fine. I have an SPDT switch to change the value on Input_GPIO5 between 0V (GND) and 3.3V (VCC). I have cathode of an LED connected to Output_GPIO
-
Nth Order Filter Coefficient Calculations
Anyone have Code/Algorithms to calculate the coefficients for the Nth Order filters? For a 10th order fiter there are 5 sets of coefficients, but they are all slightly different, not just cascades of
-
8.24 format
In wiki 8.24 format heve some different number of bytes. Its from wiki 8.24 1111 1110 0000 0000 0000 0000 0000 = -0.25 28 bit in example 0000 0000 1000 0000 0000 0000 0000 0000 = 2^23 - 1 LSB = 0dBFS
-
MCU控制ADAU1701 EQ 核心问题
8461.SigmalStudio.zip 多谢你的指教,我问题的核心是:上图所示,我把gain一改成10,就对应出来5个浮点数,那么我其实在实际产品是用上位机通过MCU去控制Gain的,那问题在于,我要把gain=10的指令发给MCU,MCU是通过什么样的算法,把10转化成那5个浮点数的呢? 谢谢指教 Edit Notes 多谢你的指教,我问题的核心是:上图所示,我把gain一改成10,就对应出