EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Is there any advantage to increasing the bit depth within Sigma?
Please pardon an ill-stated question by one who has been indoctrinated by decades in the analog domain, but... 24-bit resolution is generally considered quite the cat's meow in audiophile circles. 16-
-
[Bug Report] SigmaStudio Ver. 4.1, Build 1, Rev. 1761 - - Problem adding algorithm in first-order filter
A project developed in a previous, 3-point-something version of SigmaStudio had a bit of a hissy-fit opening in the installation of 4.1 that I'm running now. Warning messages on the screen could be by
-
ADAU1450 master interface read/write
Dear everybody, Could any one help to check the project,(see below link). why the master interface read/write module don't work correct? https://www.dropbox.com/s/k2v0qq82veitt91/ADAU1450%20template%2
-
Lookup table differences between Sigma3.11 & Sigma4.1
Hi all, I'm translating a project for ADAU1450 to ADAU1452 and I need to use Sigmastudio4.1 to support it. The previous project was compiled in Sigmastudio 3.11 and actually I'm finding some problems
-
ADAU1701 Std RMS Compressor Level Readouts from MCU
I am working on integrating adau1701 device functionality into my linux library for dynamic dsp controls. I have all the writes and reads happening properly between the devices running ADAU1701 and AD
-
Roconstruction-Filter in the ADAU1761
Hello guys, I found the ADAU1761 with internal AD-/DA-U´s. My questions, is there a reconstructionfilter in the DAU´s to restore the continious time signal? Best Regards Viktor Audio Signa
-
MP3 decoder for SigmaDSP
Hi, I understand MP3 decoder is not implemented in SigmaDSP standard library. Is there any 3rd party vendor for SigmaDSP MP3 decoder ? Thanks and Regards, mp3 decoder SigmaDSP
-
ABOUT THE ADAU1701 TEST MODE only for test hardware board if start work
Hello everyone! I am using the ADAU1701 and have worked out the PCB , and now i only want to test the ADAU1701 if its started working hard! now the setting is selfboot mode , the selfboot pin tied the
-
ADAU1701 eval board controlling ADAU1372 codec eval board
Hi there, Just a quick one on using the eval_adau1701miniz to control the eval_adau1372 DACs. I noticed the eval_adau1701 board only has sdata_in bclk_in and possibly no way to output MCLK. Am I looki
-
SigmaStudio: Can't save/reload design with heirarchy blocks using downsampling ADAU1452
I have found a troublesome bug in Sigma Studio. I am working on a large design for the ADAU1452, and the sampling rate is 192kHz. There are some control blocks that do not need to run at this rate. Th
-
Questions about ADAU1978 in SA mode
Hello I want to use the ADAU1978 in SA mode. For this I connect: 1. SA_MODE to IOVDD (for standalone Hardware mode) . 2. ADDR0 to GND (for I2S mode) 3. ADDR1 to IOVDD (Slave mode). SigmaDSP processor
-
EVAL-ADAU1467 I2C communication
Should it be possible to use i2c instead of spi when programming the eval board with USBi? There are no problems using spi. However, in my final application, an mcu will program the dsp using i2c, so
-
ADAU1701 Signal flow design
Hello I am looking for someone who can design the signal flow for BIAMP speaker system in a professional manner in sigma studio. because I am not that experienced into using that software, the hardwar
-
Sound distortion when loading registers from STM32
Good day! I use the STM32F303RC microcontroller, DSP ADAU1452 (xtal 24.576) in conjunction with the ADAU1962A DAC (clocked with DSP). The compiled project in SigmaStudio placed in the STM32 memory and
-
ADAU1452 - ADAU1452Reading signal level via SPI
Hi, I am using SigmaStudio 4.2 to set up a circuit that includes reading signal level values from an ADAU1452 into a uC using the SPI interface. I've used the "Low Data Instructions" item (two of them
-
ADAU1701 TDM Input Processors as Slave
Hello, I am updating some designs and replacing a codec with an ADAU1701 and I am having a bit of an issue getting the audio Data in. I have used the ADAU1452 in some of our other projects and am fami
-
Accessing SPDIF/I2S raw data
I'm using a ADAU144x eval board to convert an SPDIF input to an I2S output. The SPDIF input is a proprietary format with 3 data channels, each with left and right subframes. The data in each subframe
-
ADAU1701 Low Instruction Level Detection Readback
Hi! I need to read back some signal levels to the microcontroller in my current project via I²C. This works as expected with an "Envelope Peak" block together with a readback cell. These two cell
-
EVAL-ADAU1467Z Documentation mismatch. Documentation available Rev.A, Product received Rev.B
I bought the Evaluation Board. Unfortunately the documentation on the site is of version A, while the Evaluation Board received is in revision B. As shown in the attached image, on the left I took the
-
startin project with sigmaDSP
Hi guys, I have to start a project which include a sigmaDSP processor. For me is a first experience of programming this kind of DSP. The project consists in a multi-way loudspeaker processing for a St
-
Encapsulate C code into SigmaStudio modules using SigmaStudio for SHARC
Hello, I have already developed several audio effect algorithms for ADSP-21489 in C, which run successfully on the EZ-Board using CCES. Now I am considering to encapsulate the C algorithm into Sigma S
-
ADAU144x and ADAU1962 TDM8 serial output configuration.
Hello, I'm having troubles setting the serial ports to TDM8, I've previously worked with 2 channel DACs and SigmaDSP but this has me stumped. ADAU1962 is master in standalone mode, TDM8 pulse. ADAU144
-
CLKOUT on ADAU1467
I'm working on a system that provides usb-to-i2s bridge audio, where the usb chip is supposed to act as i2s slave. ADAU1467 will be the i2s master. Besides i2s bit and frame clocks, the usb chip also
-
ADAU1466 - SPDIF 5.1
hello I recently purchased eval1466 from the first series. I have to admit this is a great quality combo but I am wondering if connecting a SPDIF signal with TOSLINK I am able to receive a multi-chann
-
[Bug Report] Sigmastudio 4.2
I found on sigmastudio 4.2 but it could be common to some previous version that in the "Limiter with indicator" block the signals Limiter Ratio and Limiter Active flag are exchanged. Found on Win7, Si