EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Implementation of N-Channel Peak Compressor for ADAU1452 & Sigma Studio 4.2
Does this module process each channel individually? Or is processing applied to all channels when any one channel exceeds threshold? Edit Notes Wording. [edited by: sgoldburg at 11:46 PM (GMT -4) on 2
-
Driving Multiple ADAU1452 from One USBi
Is it possible to drive multiple ADAU1452 from a single USBi and flash different configurations to each DSP? Audio Signal Processors adau1452 i2c spi usbi sigmastudio SigmaDSP Audio Processors SigmaDS
-
EVAL-ADAU1701MINIZ vs EVAL-ADAU1401AEBZ
Hello, I would like to determine which Sigma DSP eval board is right for my project. Can you tell me the difference in limitations between the EVAL-ADAU1401AEBZ and the EVAL-ADAU1701MINIZ evaluation b
-
ADAU145x Setting default volume
Hi, After browsing the forum I have found, that people have been having a problem with the DSP resetting the volume to maximum after reboot and nobody seems to be answering that question. I just wante
-
Programming ADAU1702
Hello, I´m currently at the very beginning of a guitar amp design using DSP (ADAU1702). I´m trying to figure out how I could program this device. I need a self-boot operation since I don&a
-
urgent: generating coefficients for 2nd eq filter
Hello every one, I am a bit confused between different Q & A that I found so far for coefficient calculation. I have general Eq (2nd order filter) cell in my signal flow , It is set to be high pass fi
-
ADAU1452 how to split CLKOUT signal
Hi, I have a quick question. I want to connect 3 x DACs (PCM1798 from TI) to the DSP and was wondering, how can I split the Master Clock signal (from pin 23) to connect to all 3 DACs? I've noticed tha
-
ADAU1761 - reading interface registers
Hi all, I am using the ADAU1761 to calculate 6 different values, these values have to be read by a microcontroller to be processed further. With the ADAU1701 I could use the interface registers to wri
-
Is there any application guide for SSM3525?
Hello, I would like to use the SSM3525 to characterize a loudspeaker such that the power delivered into a varying load impedance is proportional to input signal only. Ideally, I would like to be able
-
Can we get the effect of two identical compressors blocks in cascade from one?
Hello, I have two identical compressor blocks in cascade. Each has three points. As an example: Point A: (-90, -113), Point B: (-60, -48) and Point C: (4.8, 6) I need to use two such blocks in cascade
-
General Eq (2nd order) Slew Vs General 2nd order filter
Hello, Not being super professional audio, I want to know if I use the general Eq (2nd order) slew instead of general 2nd order? The reason is that the user should be able to change the slew ( slop) d
-
Sigma Studio DSP layout question (using ADAU1701)
Hi Bob, I have 2 questions, but I'll start with this one: I created a 2 -way speaker EQ design a couple of years ago using Sigma studio, with the help of my supplier in China. We had some self noise i
-
standard RSM compressor
Hello, I am using standard RMS compressor in my signal flow. However, it is some how confusing when I change one variable(threshold) in the cell and I look at the capture window. In the capture window
-
Error - EvalBoard144x Device is Not Supported - Sigma Studio v3.5.7
Hello, I have an audio amplifier application that uses a Sigma 200 (ADAU1446). The amp software is built to support a signal flow using Sigma Studio v3.5.7. I installed v3.5.7 x64. When I opened the s
-
I am at the age I need hearing aids. I have used the SDK ADAU1452. I created the left channel and it works great. But I try to duplicate the GUI for the right channel and I run into problems. I cant create a new 1 in and 8 out. How do I make a second
Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
ADAU1466
Is an Altium Library available / planned ? (PCB, symbols, schematics…)
-
Single volume gain math
Hello, I used the "Single Volume " for user gain. The user should be able to adjust the gain through our GUI. It would be great if you let me know how to do the conversion from dB to "value" and to "h
-
Indirect Parameter Access Table Read/Write to same parameter
Hi, i would like to perform both reading than writing to a parameter but don't know how to. In the wiki is explained that two separate indirect addresses should be used but looks like the image is mis
-
ADAU1452 remember rotary encoder volume value after reboot
I have a rotary encoder adjusting the volume of a sine wave, and it works fine. Here's my schematic (project link attached below) It reads the interface register 0 and also writes to it. However, when
-
Ambient noise compensation on ADAU1701
Hello I am trying to create an ambient noise compensation circuit in Sigma Studio for an ADAU1701. I need maintain a constant ration between the ambient noise microphone and the playback. I need to be
-
Urgent: need RSM read back cell
Hello, Currently, I am using peak read back cell to read/measure incoming audio signals in my ADAU1476 signal flow. However, I need to put RSM reader in order for local mcu to read the value and repor
-
losing faith in SigmaStudio V4.x
I have now experienced a problem with SigmaStudio V4.x (tried V4.1 and V4.2). Built a design to use the ADAU1452, compiled it without error and saved it to hard disk. The next day I try to load it and
-
How to choose a big memory size DSP for the signal delay design?
Hello everyone and SigmaStudio teams: I am trying find the chip which has the big memory size that can support the huge delay function, I have tried the delay 600ms at 1452, but this will use all 1452
-
3rd order butterworths in ADAU1701
Hi. I know that “Linkwitz-Riley – 36 dB/oct = 2 cascaded 3rd order butterworths and 3rd order butterworth is implemented by cascading a “HigherOrder” + 1st order” I need to make a 3rd order butterwort
-
Programming the EVAL-ADAU1452MINIZ from MCU via I2C
Hello, I would like to program the EVAL-ADAU1452MINIZ via I2C from an MCU. I am following the this link how-do-i-create-the-microcontroller-code-to-interface-to-my-sigmadsp I will not use the SPI for