EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAu1467 can't self-boot from AT25DF321A (EEPROM)
Hello, We needed to have apparently really large size EEPROM for our application. So the designer used "AT25DF321A" which is 32 Mbit SPI flash memory. The ADAU1467 failed to self-boot successfully whe
-
How can I make an ADAU1701 crossover filter with dynamic uC control of frequency and filter type (BW12, BW18, BW24, BW66, BW48 and LR12, LR16, LR24, LR36 and LR48) but using the few instructions as possible?
Hi. I need your help. I’m working on a project where one ADAU1701 is controlled by an 8 bits uC c8051F020 on I2C. Everything is right. But… I’m running almost out of instructions: 978 (out of 1024) an
-
DSP ADAU1702
i want to use the ADAU1702 for my application, My application is musical fountain, i need to give different sequences to drive the water valves corresponding to the audio song, it is for basically fre
-
Writing a selfboot EEPROM (ADAU1701)
Hello folks, I'm trying to write to my board's EEPROM directly with I2C and not use a USBi device with SigmaStudio (small project, not looking to invest in an expensive USBi/Eval board). However I'm r
-
TIME WEIGHTING IEC61672
I am trying to implement Time weightings Fast and slow as written in IEC61672 with ADAU1761 SIGMA DSP but didn't get a satisfatory result. The idea is make a noise measurement equipment. Fast time con
-
DSP readback addressing
Hello, is there any way to force sigmastudio to produce contiguous ReadBack addresses in order to read N parameters at once in burst mode ? This is an excerpt of what i get now out of sigmastudio : #d
-
ADAU1978 configuration
Hi, I am going to use ADAU1978 audio codec. I have 3 MICs connected to 3 of the ADCs on the codec. I use I2C interface between the codec and STM3F407. What are the register settings that needs to be d
-
Sigma Filter Foibles - ADAU1701 (and beyond?)
This relates to the development board for the ADAU1701 running under SigmaStudio 4.1. The first observation was related in another recent thread, but because that thread does not have 'filter' in the
-
ADAU1442 output port corruption with unassociated async input clocks
Hi, we are having an issue noted with ADAU1442 SigmaDSP on a custom PCB that may point to possibility of a silicon bug on the DSP. This project has had >1kpcs made over the past four years and behavio
-
Wishlist: DSP Parameter Read with input pin for address and output pin for data
It would be a nice feature to have a cell block with an input pin where you can connect a DC block with the address you want to read and an output pin to put out the data from the reading address. The
-
Hey! How to configure the I2C master output in SigmaStudio?
Hello everyone I have ADAU1451. How to configure the I2C master output to send to it logic signal (0 or 1)? Thanks. Audio Signal Processors adau1451 SigmaDSP Audio Processors
-
Selfboot problem in ADAU1452
Hello Team, As per ADAU1452 evaluation board user guide's procedure, I followed but self-booting is not happening. Kindly advice if there is any procedure to follow. Audio Signal Processors adau1452 S
-
Custom Modules for ADAU1452 DSP
I am currently testing the ADAU1452 DSP.by using the EVAL-ADAU1452 evaluation board. That is the perfect choice for my application in terms of hardware, especially as I need 4 PDM digital microphone i
-
EVAL-ADAU1452MINIZ: DAC DC output?
I need to generate a DC control voltage from this board. All of the analog outputs are AC coupled through a 10uF cap. Can I jumper-out those caps to get the DC I need? The DC will feed an op-amp circu
-
ADAU1761 output power to headphone
Hi ADI's I have a question about the DAC TO HEADPHONE / EARPIECE OUTPUT power of the ADAU1761. On page 8 of the datasheet, it is shown below. (Po = 10.6 mW when AVDD = 3.3 V, 32ohm load) And looking a
-
Hard clipper bug, or am I losing it?
I'm using the Hard Clip function under Nonlinear Processors in the ADAU1701 platform, and think there's something amiss. If I pull-down a single clipper package, all is well. I can set it to + and - v
-
ADAU1467 Dual Master Control Port
I'm starting a new thread based on this post by DaveThib: "If you absolutely MUST use a SPI EEPROM for fast booting and be able to control some I2C parts then you will have to move over to the Sigma35
-
So, what toggles a GPO pin, anyway?
I suppose Sigma chip GPOs are supposed to be triggered by logical elements, like a one-shot, a gate or the Tolerance Analyzer. But I'm creating a PWM output from the ADAU1701 using an ABCD module and
-
ADAU1701 Lock-in amplifier
Hi, I would like to design a "Lock-in amplifier" using ADAU1701 DSP chip. Lock-in uses a technique known as phase sensitive detection to single out the component of the signal at a specific frequency.
-
error in DM0 Bank 0 and startup verification
Hello EngineerZone, I have a question regarding the "PANIC FLAG", "ERR_DM0B0" and selfboot-startup verfication in ADAU1451. I have searched for similar topic and also found one, but it is closed and w
-
ADAU1450 Volume with External ADC control not working, please help
Hi guys, I have configured the schematic using ADAU1450 in which I am facing a great difficulty in making the external DC volume work. I am using Log lookup table and not clear on what values I should
-
ADAU1701 - I2S interface with BCLK 32 FS
Hello my friends! I am trying to get the ADAU1701 to work with a Bluetooth module which is only capable of providing a Bit Clock that is 32 x FS. I believe the standart I2S uses 64 x FS for Bitclock.
-
SigmaStudio 4.1 crashes on startup in Windows 10, but runs in Safe Mode
Hello, I have just installed SigmaStudio 4.1 64bits in my windows 10 machine, but when trying t start the program it crashes I tried running it in compatibility mode on windows xp, 7 and 8, without su
-
ADAU1452 Audio problem
Hello Team, We are using ADAU1452 evaluation board. While testing with evaluation board the whole thing was fine. We got output as per our requirement. And then we made a customized board with similar
-
Determining resource use for the ADAU1701
It's been awhile, but I've used the ADAU1701 for a few projects and thought I had an intuitive feel for how close a design came to maxing-out the chip's resources. A new design, which looks as if it s