EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1463WBCPZ150 PCB Design
Hello, I’m considering moving forward with a custom PCB board for the ADAU1463WBCPZ150 audio DSP chip but I was wanting to get some clarification on a couple of things first. Can someone tell me if th
-
ADAU1761 calculating coefficients on a PC
Hello, I'm using an STM32F103 acting as mass storage flash and a FatFS file system on board which allows me to take a hex file so I can upload this to a ADAU1761. Looking at the output from the SigmaS
-
How to configure slide switch as 3 input and 1 output
Hello Team, I need configure a slide switch in ADAU1452. It need to perform three operation using slide. The operation's are, 1. Mic Output 2. Transducer output 3. Both. If I slide only mic output sho
-
How to use slide switch for multiple inputs
Hello, I want to use slide switch in sigma studio for multiple inputs. Please tell how I can use slide switch in sigma studio for multiple inputs. Thanks and Regards, Sandeep
-
Peaking filter and Notch filter coefficient formula
Hello guys, I have some problem on calculate the Peaking and Notch filter. In SigmaStudio wiki ( SigmaStudio Wiki ), I can not get both filter formula information, and I reference the Robert Bristow-J
-
Microphone connection to ADAU1401A
Hi, Is it possible to connect a microphone to ADC of ADAU1401A? Since there is not MICBIAS, etc. on ADAU1401A, so I believe that it is difficult Do you know any solution to connect a microphone to ADA
-
Application Exception "Object reference not set" Sigma Studio
Hi at all, I have a big problem and tried to fix it for hours. Now I came to the conclusion that I need help. I used my" starter project" many times as begging for real practical projects. So it worke
-
ADAU1777 problem with more than 16 instructions
Hi, I have a simple setup where Input 2 feeds 7 "General (2nd order)" filters and sends out OUT0. Similarly Input 3 feeds 7 "General (2nd order)" filters and sends out OUT1. The compiler says the inst
-
SECOND_PAGE_ENABLE bug?
As I cannot publish my project I will try to explain the issue: With SigmaStudio-4.0 and Eval-ADAU1466 board: In a complex and big project I have sch blocks on memoryPage_1 and memoryPage_2. Depending
-
How to change USBi EVAL-ADUSB2EBZ data rate
Hello, I have a question how to change USBi EVAL-ADUSB2EBZ data rate. When SPI communication is made to the DSP with EVAL-ADUSB2EBZ, it seems the speed is about 300 kbps. Can I change the transmission
-
Hardware Configuration Register Blocks- Data associated with Addresses is inconsistant
Hello, I want to note the address and data associated with the changes (toggle values) I make in the register control window and use it with an external uC to control various settings in my program. I
-
NOISE REDUCTION FOR AVDD ADAU1701
Hello everyone, do you think that by inserting a filter on AVDD as visible in the attached image, it is possible to improve the noise on the internal analog circuits on ADAU1701 more? Thanks Piero Aud
-
ADAU1701 PLL modes for 45.1584 & 49.1520 MHz MCLKs?
Hi guys, hope you could help me figuring out, if a allo kali reclocker with its 45.1584 & 49.1520 MHz MCLKs is compatible to the ADAU1701 and if so, which PLL_modes to use (s. Setting the PLL mode for
-
How to use Gpio Expander
Hello Everyone, Am using ADAU1452 DSP Processor. I need to control (multiple)push buttons using singe GPIO. Is it possible to control using one GPIO. Or-else using resistor ladder network can be able
-
How is SafeLoadModule activated for ADAU1466?
I have a processing scheme for the ADAU1466. I export the files in C with the Export System Files button and in the parameters file I have the following: /* Module SafeLoadModule - SafeLoadModule*/ #d
-
ADAU1466 Serial Port 2 Configuration
I am looking for assistance with setting up Serial Input Port 2 as an I2S input using SigmaStudio 3.17. I have created a project with a Input block with channels 32-33 selected. This connects to a two
-
[ADUA1701] Auxillary ADC input and tolerance analyzer. How to use?
Hello! At this time i'm in the learning curve about the ADUA1701 DSP chip. One of the things that i'll try to understand how the tolerant analyzer works when connected to one of the auxillary ADC inpu
-
Where to write in EEPROM "set multiple writeback" ?
Here the problem. I read in the ADAU1701 datasheet, that I have to set "Set multiple writeback" so that every time I change parameters, a writeback occurs... By default writeback is only enabled "one
-
Index-Selectable Limiter Block
I am currently using the Ext Detector Standard RMS Limiter block (look-ahead limiter). Is there a way to make the limiter parameters indexed based on an input to select from four different limiter opt
-
SigmaStudio script and Visual Basic
I would like to import data from the registers of an evaluation board to an excel spreadsheet via Visual Basic and the SS scripting language. I'm not an experienced VB user and would appreciate a tuto
-
How to control several Push button using one GPIO
Hi Everyone, Am using ADAU1452, I need to control volume,frequency, Pitch using push buttons. I didn't find any free gipo's in my schematics. How can we control 7 push buttons using one GPIO. I have s
-
ADAU1777 - Questions and Bugs v4.0b2r1759
I know that the ADAU1777 is not a standard sigmadsp and is limited to basics like biquad filters and limiters. Is there also a limitation on the order of how these blocks are placed? With a limiter on
-
Introduction, and some questions about ADAU1701
Hello everybody who reads this. my name is John and i'm from the Netherlands. = = I own a lot of older Dynacord power amplifiers. They are very well builded. They do not have lots of power or are ligh
-
Is there any Sigma Studio verision can support 32 Bits OS and ADAU1466?
Hi ADI Expert, My computer is Win 7 (32 bits) and I'm using 3.11 version for developing SigmaDSP. I would like to develop ADAU1466 but I found the latest version SigmaStudio are all 64 bits version. M
-
How to generate double angle formulas
Dear Mr/Ms, Could I ask you some questions about sigma studio software? How to produce a sin(3*x) or sin(4*x) signal according to the input sin(x)? Many thanks. Best regards, Shaogang Yu