EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 + SigmaStudio + REW = Auto EQ ?
Hello, I own a DSP using the ADAU1701, I set it using SigmaStudio. I'd like to use the Auto EQ feature. Did someone can guide me to the right way to use Room EQ Wizard (REW) to get an "auto EQ" file (
-
Communication between ADAU1442 and PIC16F877 microcontroller
Hello Everyone, I am new in DSP field and I want to enable communication between the ADAU1442 and the SigmaStudio programming tool via the PIC16F877 microcontroller, where I want to glow led on Analog
-
Internal GPIO binary encoding for external logic control
Hi everyone! I have a question regarding toggle counter output control signal to GPIO binary signal encode. So when multiplexer input #0 is selected, then GPIO DIG2 - DIG1 (bit 1 - bit 0) is binary 00
-
Communication between MEMS mic and ADAU1701
Hello everyone, I received an ADAU1701 evaluation board two days ago and I try to receive data from a MEMS mic which communicate with I2S( https://www.adafruit.com/product/3421 ). I am sorry if my que
-
Why did the filter parameter order change ?
Hi, In SS 3.15 Build 2 Rev 1721 a new algorithm for the double precision filters is used. I checked how this will affect the parameters and found that the order of the parameters in RAM has changed. T
-
Crossover Coefficients ADAU1452 with Microprocessor
Hello, I am implementing a configurable DSP architecture using the ADAU1452 and loading and controlling the device from Linux. I have worked out most of the required blocks and calculations and am wri
-
Level Detector indicates minus number.
Hello, Please see attached schematic. This signal level detector indicates minus number. Does LevelDetector module have RMS calculation or ABS function? Or Is Level Detection function (RMS, ABS, etc.)
-
Getting digital microphones to work on EVAL-ADAU1777Z ?
I am trying to get a digital microphone input to work on EVAL-ADAU1777Z. I have successfully brought up examples using 4 analog input channels through the ADCs. I have some digital PDM mems microphone
-
Loudness module generates noise
Hello, Please see the attached loudness module schematics. Loudness module generate pop-noise, when filter selection was changed by our controller. This loudness module have Smoothing Feature. However
-
Manually setting I2C addresses of components in SigmaStudio
Hello all, I wondered if it is possible to set the I2C addresses of components manually in Sigma Studio. In my project I have some DC generators I want to set every 100ms which I have to do with safel
-
ADAU1467 Can't set SDATA IO
I tried to configure Serial Inputs, Serial Outputs and SDATA IO with EVAL-ADAU1467Z. Serial Inputs, Serial Outputs no problems but when I activate SDATA IO seams not to work. SigmaStudio 3.16 and Sigm
-
how to impliment 4*1 multiplex in ADAU1701?
hi, i am using ADAU1701. we have four different signal with different frequencies. i want to send only one wave to output by using two switches selection. Just like 4*1 multiplexer with 2 delectable l
-
Problem with e2prom self-boot on EVAL-ADAU1777z
I am a new user of SigmaStudio and I am trying to boot from the on-board EEPROM. I am following the directions in the AD user guide for this product ( http://www.analog.com/media/en/technical-document
-
DM0 and DM1 after reset in ADAU1450
Hi all, A while ago, I posted a question about the state of the RAM registers in the ADAU1450 after reset: DM0 and DM1 RAM content after RESET ADAU1450 Dave responded that RAM is initialized just befo
-
ADAU1401 selfboot, reconfiguring EEPROM
Hello I am currently using a ADAU1401 DSP and SigmaStudio 3.17. I would like to have following scenario: I have a EEPROM with preconfigures settings. A customer should be able to change the DSP settin
-
Need help correcting speaker frequencies
Hi, On request of a friend we're building an omnidirectional bluetooth speaker. Because space is very limited we bought an ADAU1701 to correct the sound for it. One of the problems we're facing is the
-
ADAU1442 maximum input voltage at s/pdif input port
Hi All, Is the s/pdif input pin on the ADAU1442 TTL (0-5V) compatible? If not, what is the maximum input voltage on this pin? Thanks for your answer! Kind Regards Julius Audio Signal Processors s/pdif
-
ADAU1701 PROBLEMS WITH AUX ADC
I have configured the input for an AUX ADC as the attached image, I do not understand why the audio played is very noisy, to have a discrete playback, it is necessary to set the control adc in SigmaSt
-
adau 1772
Hello everyone! we are currently designing a new product, based on ADAU 1772 audio processor. We need to measure RMS value of the signal for at least 0.05s. We trued the Single Level Detector (SigmaSt
-
SigmaStudio 3.17- block processing sort of works now..maybe?
Hi Team (I am using adau1466 eval): Well, was very excited to download 3.17 and see that I can finally pass audio through a FFT/IFFT combo- first time, thanks! But, seems to be many more bugs relating
-
CODE CAMPATIBLITY BETWEEN ADAU1450/1/2
Is code generated for the AD1450 compatible with the ADAU1451 and ADAU1452.. The design utilizes the ADAU1450. But for second sourcing considerations , can the ADAU1451 and ADAU1452 be substituted wit
-
ADAU1701 / ADAU1401 SPI Interface Timing
The ADAU1701 and ADAU1401 data sheets specify maximum SPI clock CCLK frequency as 6.25MHz. The data is available on the COUT pin up to 101ns after the CCLK falling edge according to the table above, b
-
New DSP with Codec and sound file functionality?
Good evening Dave, sorry if I go out if topic but I need urgent information I have read, but I do not remember where Analog at the beginning of 2018 would have commercialized a new DSP similar to ADAU
-
ADAU1701 FM MPX stereo encoder problem
So I tried to make an FM stereo encoder. You can see my schematic in the attached picture. I do not have a scope with me right now, but that will probably be my next thing to try if I don't get any hi
-
About SPDIF Receiver block on ADAU1451/2
Is the SPDIF receiver on SigmaDSP processors compatible to process HDMI ARC signals? If yes, is there a recommended interface circuit to do so. Converting the differential signal to single ended can b