EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1452 Board Startup - Noise Source and level detector
I've setup the eval board, added a white noise source and a single level detector monitor. Turning both on show no signal level on the level detector. BTW, the white noise source switch indicator bar
-
When is the adau1466 avialable?
This part seems to be delayed, along with others in it's family? Website still says release is July 2017... -Gary Audio Signal Processors SigmaDSP Audio Processors adau1466
-
Sure Adau 1701 external Potentiometer
Hello I got the Sure Adau1701 Board and want to do an external Volume control over an 10k Linear Potentiometer. I use the litte dsp for my mobile Boomboxes. In my earlier versions i use the miniDSP. T
-
ADAU1452 - warning (27,ExtDelay1): Preprocessor macro re-definition?
Hello, i get this warning once i do the link-compile-connect or link-compile-download: warning (27,ExtDelay1): Preprocessor macro re-definition of 'PIN_DRIVE_MAX_SPEED_NO_PULL'with different value (39
-
Extra SDATA_OUT on ADAU1452
Hi All, I'm using SDATA_OUT3, SDATA_OUT1, SDATA_OUT0 to send data to Amplifier chips. The Amplifier chips only support I2S, so I cannot use TDM to reduce SDATA_OUT pin count. SDATA_OUT2 is used for tr
-
ADAU145x IOVDD Voltage Specification
Hi, ADI Support Team I have a question about IOVDD of ADAU145x. The IOVDD Voltage is specified in Table 2 and 3 of the datasheet (Rev.C) as follows. Min 1.71V Typ 3.3V Max 3.63V However, I find a lot
-
Sigma Studio setting-modified
I have a problem on Sigma Studio system. I built a large project which has many delay units and multi-channel mixer units in it, and after several save and load processes, I found the problem that sev
-
[Bug Report] Flash Programmer block
Title: an error window appears at download time Description: this happens in Sigma Studio 15.2 Beta but not in 3.14 SigmaStudio Version: 15.2 Beta Release OS: Windows 7 flash programmer
-
25AA1024 can not be programmed though I2C USBi
Hello, I am working on a custom board with ADAU1452. The ADAU1452 should run in selfboot mode. Therefore, I attached a 25AA1024 SPI EEPROM coping the schematic from the evaluation board. An USBi conne
-
typo in the SigmaStudio Filters wiki page
Dear all, I came across the expression of a bandpass and a bandstop IIR filter: General Filters [Analog Devices Wiki] It seems that is a typo in the expression in the parenthesis as shown in the attac
-
Master Control Port Interface R/W
Hello, i'm testing Master Control Port Interface Read and Write through SPI with GPIO triggering. I'm trying to write a simple value then read it back at boot time but this seems not to work. I opened
-
SigmaDSP with PWM or Σ-Δ modulator outputs to drive H-bridge Class-D ?
SigmaDSP is great for digital audio processing, but since the systems are becoming more digital from input to amplification, I'm actually missing PWM or Σ-Δ modulator outputs in order to directly driv
-
ADAU145x Clock Configuration of Serial Input Port
Hi, ADI Support Team Currently, I am considering the following system. Is it possible to configure this clock connection in ADAU145x? Actually, I am concerning that it is not possible, because the clo
-
memory usage
is there an easy way of getting the memory usage (programme memory) out of Sigma Studio? the linker gives cells used, but I'm not sure how this relates to memory.
-
Negative Flag
in sigma studio, is there a way of flagging a negative number? I need an output if the number is negative so I can encode it.
-
We’ve run into some issues with the latest SigmaStudio Beta (3.15.2). When we compile code with the ADAU1777 we find that we can only use 30 of the 32 available slots. Can you look into this on your side?
We’ve run into some issues with the latest SigmaStudio Beta (3.15.2). When we compile code with the ADAU1777 we find that we can only use 30 of the 32 available slots. What are we missing? thanks Inte
-
ADAU1701 as audio (synth) oscillator
Hi, I could not derive this from the datasheet, but can this DSP be used as a oscillator (sinus, square, sawtooth ...) in a synth setup? Cheers, BC Audio Signal Processors SigmaDSP Audio Processors ad
-
Aux_ADC and Single Slew Ext Vol introduces noise.
I've been getting noise (hiss) in my project when (and only when) a test signal is applied. I've tracked the problem down to the single slew external volume control, more specifically when it is contr
-
Complex multiply fft
Hi: I really need this to work for a new application of the 1452... see some comments that it is not working, and I also seem to have issues. Anyone at ADI to verify it works or not on adau1452? Worki
-
Use of passive output filters with AD1934
Hello, Like with the ADAU1962A and the ADAU1966A, I would like to be able to use the AD1934 with passive output filters. Kindly suggest the recommended circuit with component values. Thanks in advance
-
Help with ADC noise in one channel please.
Hello, Setup: 2 channel ADC set up as master into ADAU1446, as slave. I'm having a slight problem in that I am getting full range noise (white noise/hiss) on one channel of my ADC, only when a signal
-
FFT issues
I have seen a related question asked (with no answer.) It seems like the new FFT additions for the 1452 part are either not working or somewhat useless. I can't seem to get any output when using compl
-
ADI Superbass seems to be very broken
Hi all, I have been experimenting with SigmaStudio and ADAU1701 to good results so far. One Algorithm that seems to be elusive though is the "ADI Superbass" - which is a shame as it is the most releva
-
Limiter indicator led
Hi, I am looking for a very low instruction usage setup which can switch on a led when the treshold of a limiter is reached. I have this setup: But the signal detection block, stays on too long as the
-
How to control ADAU1452 by external I2C interface
Dear ADIer I want to understand how to control sigma dsp via external I2C processor for volume control in my project which is composed by input, volume and output. I'll be appreciated if you explain t