EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Master Control Port Runtime Sequential Write (ADAU145x)
I'm in the process of making schematics/PCB for my system, which includes the ADAU1452 and an ADC with built in PGAs that can be programmed via I2C. It would be very convenient to use the ADAU1452 Mas
-
Interface for Implementing NLMS algorithm in ADAU1452
Hi, I am using ADAU1452 SigmaDSP to implement an algorithm derived from NLMS adaptive algorithm. It is a dual-path algorithm,where it stores the background (shadow) coefficients. It would be helpful i
-
Noise Cancelling Headset Using SigmaStudio (3.14)
Dear engineers, I am in the planning phase of a noise cancelling headset that has one (1) speech mic (mouth level), one (1) ambient mic (ear level), two (2) other left and right mics for noise cancell
-
Getting started with DSP for audio - sanity check please
So I would like to get started with a DSP for audio processing for a speaker. Please let me know if what I'm doing makes sense and not crazy. And feel free to offer any suggestions and improvements. I
-
ADAU1452 frequency domain operation
Hi. Let's speak about the block schematic and frequency domain operations of the ADAU1452 in the complex format. Currently I'm able to: - perform FFT and IFFT with a 50% window. - add (the complex add
-
Problem with regards reading registers
Hi , I am not able to read from ADAU1761 , i am using ADUCM360 for testing . I am getting ACK for writing and get a NACK for Read . please let me know with regards to this . Thanking you With best reg
-
EVAL-21479-EZLITE USB inteface red in SigmaStudio for SHARC
Hello, I have the following hardware: ADZS-21479-EZLITE Revs DSP 0.2 BOM 1.5 PCB 0.1 with (JTAG Debugger) ADZS-SADA2-BRD DSP 0.2 BOM 1.5 PCB 1.0 ans software: SigmaStudio 3.14.0 and SigmaStudio for Sh
-
FilterTableGen Coefficient Calculation?
I am attempting to create my own filter coefficient generator in c and ran into an issue. I am using the formulas from the help documentation, which I have also confirmed elsewhere on the internet. An
-
SigmaStudio CCES not a valid tool-chain on Win 10
When I open a project in SigmaStudio, I get the following message: CCES does not appear in settings where I have seen is on other machines. I am using windows 10. Is there a solution to this? I cannot
-
Documentation error in ADAU1701-c.pdf
Pretty sure this is the wrong place to post this, but I sent to Analog support already, and they sent me here, so..., here goes. (attached, snippet of document page.) ---- I have been attempting to ta
-
self-boot "presets"?
I'm looking for a way to create a few different presets for self boot sigma devices like the 1701. I don't have a micro-controller in the system and would like to keep it that way. I want to do this w
-
Software ASRC ?
Is it possible to ASRC in software on a SigmaDSP ? I know there are a number of hardware stereo ASRCs that I can use but I have been asked if I can design a system that has 32 channels of ASRC, no oth
-
Can I run TDM16 at 96kHz?
I have done a few designs using ADAU1446 and ADAU1442 in which we run the chip from a 24.576 MHz crystal so I have done TDM8 interfaces at 96kHz without problems. Now I see from the data sheet that AD
-
how do I increase output gain at the speaker by 3 to 6 dB with minimal additional noise
simple project but I need additional volume at the speaker output of 3 to 6 dB. when I add gain to the amp I get considerably more noise out the speaker. Any suggestions?ADAU1761. Any suggestions 1761
-
[Bug Report] Master Control Port Interface Read
Title: Master Control Port Interface Read doesn't work Description: After several tests i came to conclusion that this block is not working. Unfortunately the only i2c eeprom i actually have is Microc
-
Master Control Port Interface read/write i2c
Hello, i'm using a Microchip 24aa1025 i2c eeprom, i can selfboot programs from it without a problem but i'm having troubles to read/write from master control port interface. Eeprom datasheet says that
-
USB comms fails on new Win10 computer
I am at my wits end and need help badly... please. I run Sigma 3.14 on any of four computers: a Win/Vista desktop, a Win7 laptop, and two Win10 machines. Everything is fine except on the newest Win10
-
EVAL-ADAU1772 I2S to PDM
Hi, So i just got my Eval-ADAU1772 and decided to so a small experiment. So basically what I'm trying to achieve is to convert analog mic input signal into PDM output using Sigma studio. I followed th
-
About Sigmastudio IIR coefficients
I'm a new comer to use Sigmastudio ,I have some question about the general 2nd-Order Filters module coefficients,I know how to calculate the five coefficients when use as 2nd-Order Filters,But I don't
-
ADAU1701 and SigmaTcp - Header mismatch
Hey All, I was trying to configure an ADAU1701 connected to a raspberry pi (over an i2c bus, running Raspbian) using SigmaTcp. Unfortunately, I was unable to do that in the first attempt. I analyzed t
-
Sigma Project Size increasing
Hello All, I am facing with a weird problem on SigmaStudio Project file. Below is my environment. SigmaStudio version : 3.14 Windows OS : Windows 7 professional processor chosen on hardware config : A
-
To creat a low cut and high cut filter by ADAU1761
Dear ADI, Now we met a noise issue during our designing with ADAU1761, we need to creat a low cut filter(<30Hz) and a high pass filter(>25KHz) by ADAU1761 with 40dB attenuation at least.Do we have to
-
Parallel analog I/O for better performance?
This is primarily with regard to the ADAU1701. Some of the high-end A/D convertors have an option to combine a pair of ADC together to improve SN and/or distortion performance and it has me wondering
-
Send recorder audio samples to MCU
Hello, I need to record audio signal in DSP and send samples to microcontroller to be post-processed. I need all samples at DSP sampling frequency fs, but no need to get all samples in real time in MC
-
New ADAU1777 vs ADAU1701?
Hello everybody! I am happy to be here again, after such long time... Many things have happened and hopefully I can now return to developing a new iteration of my ultrasonic device for visually impair