EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1977
Dear Support, I look for ADAU1977 Digital volume control information at D.S but not found pls advice Thank you in advance Miguel Liber
-
I2S Input - MP0,4,5 are all 3.3V?
I'm a little lost here. I'm trying to get I2S input working on an ADAU1701. I've spent countless hours debugging things, making shorter cables, wrapping cables in a ground, all without success. Then I
-
Multitone "Sine tone" - how many?
Hello I would like to build multitone (sine 1/3 octave) generator for testing audio equipment. How many sine tone block I can place into ADAU1701 (preffered) or ADAU1446? I can find any information in
-
ADAU1772 I2S input
Hi, I use the ADAU1772EVB to communicate with CSR8675 by I2S. The CSR8675 is configured as master mode and the 1772 is slave. The CSR configurations are shown in the screenshot and you can see the 177
-
ADAU1701 PLAY MSG
I propose again an old topic, hoping that with these new indications is possible to play simple messages with ADAU1701. Is there an application that can convert a waw files in formats that I enclose,
-
Control parameters in SigmaStudio without MCU
Hi all, I have used modules in sigmastudio to configure the DSP in ADAU1761. Now, I want to write C program to control the module parameters. I know that the files generated by sigmastudio can be inte
-
ADAU1772 EQ filter cannot shift 180 degree?
Dear ADI team: I was develop ADAU1772 project, and we have meet some issue need your check. There was two confusion: ① In ADAU1772 Sigmastudio system, the General Filter integrated several EQ filter,
-
Sequence for Noise Generator with ADAU1702
Buffer Dear all, using the ADAU170x and the white noise generator funtion, we would like to create a repetitive sequence: The generator will switch ON during 10 s and after switch off during another 1
-
NxM Mixer Bug
My Sigma studio version 3.14 Buid 1 Rev 1675 (11/28/2016) I use ADAU1452. In my case NxM Mixer expand to 25in x 25 out NxM Mixer does not work the first output. Others outputs works OK. Maybe module N
-
ramping up the ADAU1372z environment / sigmaStudio .
Dear Support, my customer have some problems ramping up the ADAU1372z environment. After installing the sigmaStudio SW and connecting the USBi bridge, they cannot see any clocks\data from the J4 conne
-
Inconistent Reading from ADAU1761 regiaters
We have several ADAU1761 devices each connected with individual SPI busses to an FPGA which is doing the configurations. The FPGA has the ability to trigger writes and reads to each individual 1761 de
-
Need to expand SigmaStudio State C beyond 9999999 bytes
Hello, We are developing a product using SigmaStudio 3.12 for SHARC and the 21489 DSP. We are planning on using an external SD RAM (512MB) for a pooled audio delay. Here is an earlier thread: Running
-
ADAU1452 Sigma TCPIP Protocol
Dear Sigma Studio Community, I am working on a fully integrated Audio DSP Solution with an ADAU1452. The Chip should be controlled via Ethernet connection (Wifi) from Sigma Studio 3.14.1. The ADAU1452
-
How to design a FM modulator using ADAU1401?
Dear all, I am trying to use ADAU1401AEBZ board to design a modulator. I finish the AM modulator already, and try to design a FM modulator next. I usually use a VCO IC to design FM modulator. Is there
-
About ADAU1761 and SigmaStudio
Hi I am using ADAU1761. The digital signal from the master controller is sent to ADAU1761 and DSP in ADAU1761 need to do some processing on the signal. Now I want to get the digital data output before
-
How to generate 40KHz signal using ADAU1401A?
Dear all, My project need to work at 40KHz. I am trying to use a simple test circuit to get a 40KHz sinusoidal wave first. I connect a source to the output directly. I set the sample rate to 96KHz. Ho
-
ABCD Comparator "Not Equals" Setting?
I would have guessed that the symbol shown means, "If A is not equal to B" -- but troubleshooting the logic of my project shows that it's really, "If A = B." Which is correct? abcd_logic not_equal bug
-
I2S input on ADAU1702
ADAU1702 I2S Slave configuration When the ADAU1702 is used as an I2S slave, the stream is not read in as should. The audio data is however not clearly received. This is a simplified design of our syst
-
ADI Surround Large vs. Small / Licensing
I see that the same data is written when selecting large or small. Is this an unfinished control, or ?? Help says that licensing is required, but the help is quite old. I assume that it's not. Can som
-
[Bug Report] SigmaStudio.3.13: Different parameter values in exported files
I would like to report a bug regarding the exported files from SigmaStudio. I am currently using ver 3.13. The DSP is the ADAU1701. I have seen in the Release note for 3.14 that the following is a kno
-
Karplus-Strong string synth docs?
I couldn't find any documentation for this block at all. Is there some? Example code? (ADAU1701)
-
Muting DSP Outputs using GPIO input
Hello, We have recently developed an amplifier with the ADAU1701 DSP, and one of our requirements is that once you turn it off, the output must MUTE completely extremely fast, under 100 uS (micro seco
-
ADAU1701 and I2S
Hi to all. I am running some tests with the ADAU1701 and i am little bit confused My master clock is 25MHz and it comes from an CM6631A configured to 24bit 96Khz. PLL mode is set to 256xFs. The CM6631
-
ADAU 1452 external SPI delay
Hello all, I'm trying to work with the external SPI delay for the ADAU1452 sigma studio. I used the 1Mbit 23LC1024 and everything is working as expected. To increase the delay I tried to find somethin
-
Divide an integer by 3
How to perform division by 3 of an integer number in SigmaStudio? Thank you in advance! Omar integer divide