EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
How to measure the total time from input to output in the SigmaStudio?
Hi all, I have a question is about how to measure the total time from input to output when there is a buffer before the limiter? My question is: if there is no buffer before the limiter, the signal ca
-
adau145x watchdog?
The ADAU145x datasheet states w.r.t. the watchdog: The counter is reset to the maximum value each time the program counter jumps to the beginning of the program to begin processing another audio frame
-
Selecting TDM8 streams into DSP
I have a question about using and selecting audio from TDM8 streams. I intend to use an ADAU144x device with 8 of the Serial Inputs programmed to be TDM8 streams allowing selection of audio from 64 so
-
SigmaStudio defines Parameter Names, can this be changed?
Hello, A little background: - Using SigmaStudio xml file as an export to be read by our service and values are written onto the DSP. The Cell name is generated by SigmaStudio, for example for a switch
-
ADAU145x SAFELOAD word using SPI
Hello everybody, About safeload registers: They are 32 bits registers. So, if i using SPI to load 4 bytes (1 byte at a time), the increment will occur only when the 32bit is reached? The number of byt
-
how the Q of a filter in SigmaStudio works?
Hi forum, In SigmaStudio I am using a second order general parametric EQ filter. I am setting a f0 = 500 Hz, a dBboost of -12 and a Q of 5. I then plug in the probe and the stimulus on the filter and
-
How can I change the curve of an RMS compressor with safeload mechanism?
I need to change in real time the compression curve of an RMS compressor without click and pop noise, uploading data from a microcontroller. I've seen that using SigmaStudio, when I change the curve,
-
Can ADAU1452 use 2 control ports at same time?
Hello all, I have questions as the title. Could you see the attachment and give me an idea please? Best Regards, Yuta M Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
ADAU1701 rotary encoder position
Hello, I'm very new to Sigma Studio and Analog Devices DSP. I want to make an envelope follower with a settable decay and level control thanks to two rotary encoders. I would also like to implement so
-
Paste error when loading Hierarchy Board
Hello, i get the following error when i try to load a saved Hierarchy Board: When i hit OK only blocks are loaded with no wiring between them. If i try to rewire the board and save it (with a differen
-
Problems at safeload by I2C on ADAU1452
I'm developing a board composed of arm SoC and ADAU1452. SigmaStudio v3.12 is used to create block diagrams. On SigmaStudio, "Link Compile Download" has no problem, it works well. And when I change so
-
ADAU1701 bad run quartz
Hello, Faced with the problem, the quartz resonator is run badly. The load of 22 pF connected in series via a resistor 100 ohms (OSCO). Wiring diagram standard. Runs only the touch of a finger on the
-
About ADAU1452's I2C burst mode violation.
Hello all, I got a question. the data sheet p.36 mentions what a developer must avoid as below on I2C burst mode. ・Do not issue an autoincrement (burst) write command that exceeds the highest subaddre
-
ADAU1450 Sigma Studio Bug? Instruction cycles
Hi everybody! I don´t know if i´m wrong about program memory, but for the ADAU1450 and ADAU1452 they are the same number: 8192 words. However, when i compile the same program at the same sample rate,
-
ADAU1452 Data Memory 0 DM0 size
ADAU1452 is booting trough external controller from EEPROM. As DM1 is not large enough for actual project so DM0 shall also be used, but with this the compiled project size is getting very large (3x l
-
What's the easiest way to create a stereo pan control?
I was looking through the inventory of algorithms but did not see a simple stereo pan control. I'm guessing it has already been done. Any suggestions appreciated. -CT
-
ADAU1452's electrical characteristic of IOVDD Digital Input voltage
Hello all, I have a question on the table below. Here in this table, the IOVDD VIH (min) and VIL(max) are totally same value(1.71V). In my experience, there always be some uncertain level between VIH
-
ADAU1452 Power up sequence
Hello all, I have 2 questions on the power up sequence of ADAU1452. Question 1 On the datasheet p.25, the description of the step 8 says as below. "IF THE RESET PIN IS NOT ALREADY HIGH, PULL IT HIGH A
-
About ADAU1452 bulk capacitor placement
Hello all, On the datasheet p.176, the figure 83 talks about bulk capacitor as below. Could you tell me where exactly I should place these? should I make them close to power supply or something? Best
-
about ADAU1452's grounding
Hello all, I have a question. On the datasheet p.176 grounding section, it says as below. "Place all components in an analog signal path away from digital signals." Could you tell me what this means?
-
Question about ADAU1452 PCB layout
Hello all, I have 2 questions on the figure below. Question1 On the red box on the left side, the 100nF cap is placed near to the GND not the PVDD as recommended on "Figure 81. Recommended Power Suppl
-
ADAU1452 Selfboot from I2C Eeprom
Hello, i can use Master Control Port for Interface Write/Read operations with I2C Eeprom but i can't selfboot the DSP from I2C Eeprom. I think i set everything right and the fact that I2C Interface Wr
-
About ADAU1452's Exposed pad vias
Hello all, On datasheet p.176, it is described as below. The above seems just an example. Could you tell me how the "EVAL-ADAU1452MINIZ" has the vias? and how many? (as a hardware development referenc
-
double precision filter coefficients
I am trying to implement a chebyshev filter using the values from the Chebyshev tables here: (Figure 8.27) http://www.analog.com/media/en/training-seminars/design-handbooks/Basic-Linear-Design/Chapter
-
Bug? Sigma 'Accurate' peak detector release is slow
I've used Sigma Envelope Peak Detectors in a number of applications, but was intrigued by the "Accurate" one, which I hadn't paid much attention to before. It certainly looks the same as the more comm