EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
How do I achieve a good loudness function with ADAU1701?
Is there a function for programming a loudness function in the ADAU1701 that varies bass respones depending on input level? Audio Signal Processors SigmaDSP Audio Processors adau1701
-
USBi problems with Windows 10
Is anyone else having problems using USBi on Windows 10 64-bit? I am using the EVAL-ADAU144xEBZ Demo Board but SigmaStudio fails consistently with Comm Errors. I have tried the same arrangement on Win
-
Delay noise when controlled by aux adc
Hello, i've just found that, when i try to control a delay time parameter through an auxiliary adc input with a potentiometer connected, i get a noisy output; i don't get any noise when i control the
-
Adau1452 Phase Vocoder/Pitchshift
Hi Would it be possible to implement a phase vocoder in SigmaStudio with the existing blocks? I am not sure how to do the complex math, or if a Hanning Window function is avaliable. Guitar Pitch Shift
-
Question on ADAU1452's internal LDO unit
Hello all, I have 2 questions. Question1 On the datasheet p.18, VDRIVE description says that the "STD2805" PNP pass transistor is recommended. Also, on the datasheet p.32, "Voltage Regulator" section
-
How to use I2S as input/output in Sigma Studio 3.13
Hi, i am a new user in Sigma Studio . my EV board is using ADAU1701 . i will use I2S instead of ADC input . my question is : 1. how can i enable and select I2S as input ? 2. how can i convert the in i
-
Pin detailed information on ADAU1452
Hello All, Could you see the attachment file? I would like you to fill out all the blank by the end of Nov 3rd. See the instruction on the red tab on the top right corner of each specific cell. It is
-
About ADAU1452's AC specification on Serial port.
Hello All, I have some question. Question1 About tLIS, the description mentions as below. "LRCLK setup to BCLK_INx input rising edge" Could you tell me the exact definition of the rising edge please?
-
Gerber files for ADAU1772 eval board
Hello, i am working on a school project with the ADAU1772 eval board, can you provide me with the gerber files of this eval board ? Regards, Sergio adau1772 Integrated/Special Purpose A/D Converters a
-
Write a sequence and read it back from control port
Hello, i'm trying to write a sequence to eeprom through control port and then read it back. The sequence file contains a single read to aux adc 0 register (0xF5A0). The sequence is working properly be
-
EEPROM write fails in release 3.13
Hi Dave, I'm experiencing difficulty with downloading code to the on-board EEPROM. The exact same design loads fine when compiled under 3.12, but when compiling in 3.13 all attempts to load the code i
-
How to check if Aux ADC has changed from its initial status?
Hello, i'd like to build a function that would: - check if Aux ADC is in a rest position (or within a +-1 window) and output a 1 - check if Aux ADC has changed and output goes 0 and hold the value I c
-
How can I use ADAU1701 to create decode surround
Hi, We're working on a product which uses the 1701. It's our hope to be able to use the dsp to create surround stereo sources. I've seen that there is an analog devices surround block for sigma, but y
-
Filtered NLMS filter
Hi! I am interested in using FxLMS for the purpose of ambient noise reduction by active noise cancellation, and I noticed that the filtered NLMS filter had been added to SigmaStudio 3.13. However I ca
-
About Sigma300(ADAU1452) Architecture
Hello all, I've got a question on SigmaDSP's architecture. On the data sheet p.22, there is a line just as below. "By using a quadruple multiply accumulator (MAC) data path, the ADAU1452/ADAU1451 can
-
Frequency domain multiply -FFT and IFFT
Hi: I need to do a multiply after the FFT block, but see no frequency domain blocks at all for the ADAU1452. I saw a similar question posted in 2014, but no answer... I am using the current version of
-
Where is the Full-Range RMS Compressor?
I'm running Sigma Studio 3.13, Build 4 under Windows 10, and am in the menu tree for the ADAU1451. Under Dynamics Processors / RMS / Full Range (-140dB to +40dB) / No Ext Detector Input / 1(or 2)-Chan
-
Is there a way for adau1761 work with external analog volume control?
I am a newbie and find information hard to find. Audio Signal Processors SigmaDSP Audio Processors adau1761
-
Using an momentary push button, how do I turn adau1761 on and off?
It seems very basic but I am new designing these parts. Audio Signal Processors SigmaDSP Audio Processors adau1761
- [Bug Report] Text under MOSI ADDR1 in PIN_DRIVE tab for ADAU145x wrong
-
EVAL-Adau1761Z Two analog inputs and two analog outputs?
Hi all, Forgive a very basic question but I have never used hardware like this before and am quite stumped. I have an EVAL-ADAU1761Z, I want to run two separate mono signals into the analog inputs, do
-
Limit on User Comment text?
I have recently "upgraded" (and I use the term loosely!) from Windows 7 to Windows 10. Concurrently, I replaced Sigma 3.12 with 3.13. The Sigma 'User Comments' utility is a good way to keep a running
-
Need definition of maximum value blocks
Okay. I'm a little confused here. Under Sigma 3.13, I can find several circuit blocks with the term 'max' in their name. When I pull them onto the sheet and hit F1, I may or may not get a straight ans
-
How to use EVAL-ADUSB2EBZ as standalone SPI interface
Hi, How to use EVAL-ADUSB2EBZ as standalone SPI interface from PC to any SHARC DSP? i.e. What are the API's on the PC to configure the EVAL-ADUSB2EBZ for SPI? If it is possible, is there any document
-
No output when uploadet to EEPROM?
I got a little problem with my ADAU1701. I've made a sigmastudioproject out of my requirements and everything is working great so far with the "Link Compile Download" button. But as soon as i upload t