EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
any suggestions for SigmaStudio on Win 7 32 via Vmware Fusion for Mac
Hello Trying to program the adau1701 using the USBi interface with SigmaStudio v3.12 on a virtualized install of Win 7 32 bit running on a new iMac using Vmware Fusion for Mac. Sigmastudio at first re
-
adau1701 boot from arduino
Dear friends I'm in trouble and would like your help to solve it. I developed a hardware with adau1701 and it works perfectly using the SigmaStudio and USBI interface both SelfBoot mode using external
-
ADUSB2EBZ header connector part number and pitch
I am about to finish the PCB layout of my crossover based on ADAU1702. I need information on manufacturer Part number of 10 pin [2 X 5] programming header and its pitch detail. Audio Signal Processors
-
ADAU1452 Filter control/parameters
I'm using a general 2nd order filter (with automaticcalculated coefficients) block on Sigmastudio 3.13. On this block I'm able to select the filter type. Among filter types of interest for my project
-
Beamforming ADAU1781
Hi everyone, I would like to use the fixed beamforming cell with my ADAU1781 evalbord. With the two MEMS microphone provide on the evalboard. I didn't found informations about this cell. Is there a de
-
SPI Routing / Eprom Multi-DSP ADAU1452
Hello! we want to use 2 (probably 3) ADAU1452 in a multi-DSP design. There are some questions remaining after looking at the forum and also USBi AN: - Do we for SPI communication connect the SPI Maste
-
I have a Question about detail Limiter control
Hi everybody My name is Park Cheong Su I have a Question about detail Limiter control this is My Question List 1. How to get Release Time Control formula in Limiter? 2. How to get Attack Time Control
-
ADAU 1701
Hello Guys, I do write 3way Xover program on ADAU 1701 Miniz. I do want to write and read-back as many programs as I can, but i couldn't figure it how. I also do want add one switch to save and read-b
-
pll settings or DSP at 100MHz ?
ADAU1701 MCLK=24.576 pll settings are mode0=0 mode1=1 fs=96khz. yet the adau puts out 192khz when the frame sync is set at internalclck /512.. does the dsp run at 100Mhz ? the loop filter avg voltage
-
ADAU1761 POR
Hi, I got one customer who used ADAU1761 for beamforming mic array for BT handsfree application in car infotainment system. However, they faced an intermediate issue as shown below: Current condition
-
Change delay and Volume while dsp is running
Hello, my question concerns the capability of Sigma DSP's to change algorithm parameters during programm execution. In particular I would like to change delay times and volumes to implement a phased a
-
Register Window for ADAU1452
Seeking a summary of the function of each register, and which ones are changed more frequently. Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
ADAU1701 Starting problems
Hello Analog Devices and followers, I'm a complete DSP NOOB and wanted to start exploring the world of dsp and digital audio and decided to build my own pcb around the ADAU1701 dsp. I studied several
-
Dynamics Processors
Request the Compressors processors's algorithm Information. dynamics processors
-
Is there a way to edit/modify the library algorithms in SigmaStudio?
I need to control the various parameters in the Noise Gate and Compressor library modules using an external pot. I understand how to read the pot position data in SigmaStudio...but the Gate and Compre
-
two adau1701 in serial mode with controller
Hello Now works fine for such a scheme: But i want to use one more ADAU1701, and instead ADC input use digital input and dsp power of second dsp : audio path: 1 analog in to adc IC1 and after go to di
-
I2S resistors requirement?
I understand that low-value I2S resistors are often used to limit rise/fall time of signals, and therefore reduce high frequency emissions. They're present on most, if not all of the EVB's. Is there a
-
Auto EQ Update
Hello, I'm curious if there are any plans to update the Auto EQ function within sigma studio. I like the functionality this tool provides, and the core function seems to be accurate and work well. But
-
adau1452 spi master to access peripheral hardware
We are planning our upgrade to ADAU1452 hardware from ADAU1701 hardware and would like to use the SPI Master port to offload the following functionality from our host uC to the ADAU1452: 1. Write occa
-
CAR AUDIO PROCESSOR
Hi..I'm a newbie in this field. My name is Tomo Ong. We're planning to make a DSP car sound processor using this ADAU144x (or better) And we would like to custom some of the parts if possible. For exa
-
AU1450 Crashing with SPI??
Hello, My AU1450 is working great EXCEPT that it crashes once in a while (every 5 to 10 minutes, maybe) when I'm writing control coefficients via the SPI slave port. The SPI control works; I can load
-
ADAU145x software safeload address changes, not included in header file
See page 80 of the 145x datasheet. It says that the software safeload addresses are determined by the compiler, so they may differ from the "defaults". This is indeed true... and it says to look at co
-
Output "with pullup"?
I've been puzzled a bit by the GPIO modes of the MP pins of the ADAU145x... Input (0b000) is clear: output register is ignored, input registers shows pin value. Option 0b001 is a bit vaguely described
-
sigma studio for linux
Hi there, I have tried to run sigma studio on Linux (using Wine), whilst it installs, it fails to run ! See [1] below. Is there any way to generate a firmware for a sigmaDSP chip without sigma studio
-
adau1702 straight through using Linux
Hi there, When I try to probe the adau1702 codec from Linux, it complains that it can't find the firmware "adau1701.bin". If you inspect the kernel driver for the adau1701 https://github.com/torvalds/