EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Several questions circuit design ADAU1701
Hello, Several questions circuit design ADAU1701: 1. I had to switch the settings of the two compressors. I decided to put two and switch between them. But nothing happened, output or silence or a whi
-
Software output/flag
Hello, Is it possible to somehow create a digital signal flag in my schematic that would replace a hardware output on my ADAU1442. My goal is to use that software flag and read its state from the DSP'
-
How can I get the example source code for control DSP ADAU1701 via microcontroller
Hello all, As I will design the system with APP and MCU to control DSP ADAU1701, and request MCU can real-time to update the DSP parameter to change the Low/High pass Filter(crossover Freq, Gain, Q Fa
-
Cross complie question
Hello Support. I have developed an application on the AD1940 demo board which works very well. However, I have now realised (with 20/20 hindsight) that the application would have been better developed
-
Serial port audio Input to ADAU1761
Hi all, I am integrating ADAU1761 to BeagleBone Black. The audio input to adau1761 is from the serial port input (DAC_SDATA). My questions are: 1. Should I design a system in SigmaDSP tool ? and creat
-
SigmaStudio Compiler Output result of ADAU1452
Hello, I have a question about Compiler Output result of ADAU1452. For example, I can see the Compiler Output result as the attachment file. >PM RAM used: 00000 (of 8192) Why is this value zero? What
-
mono-stable trigger
Hello bob & all, Please advise me a efficient way to design a mono-stable trigger in ADAU1701. Basically, the durance of ON state is about 0.5S. Thanks in advance! BR, Jackie Audio Signal Processors S
-
Compile Error in Project with Different DSP types
I tried to create a project using an ADAU1452 and multiple ADAU1761 however I get a compile error. The error seems to be around a Mono Switch Nx1 block assigned to the ADAU1761 though there may be oth
-
where can I get a table of opcodes ADAU1761?
I want to modify the algorithm by changing the binary file, please tell me where can I get a table of operating codes ADAU1761? Audio Signal Processors SigmaDSP Audio Processors adau1761
-
MLSSA and Auto EQ Algorithm
Hi Guys, Looking at these two algorithm is there a maximum number of data points? I ask as lets face facts MLSA is dead as a measurement system and whilst i have a deep love having worked on it for 18
-
ADUSB "USBi" Blue LED Not Going Off
Hi, I have been using the ADUSB2Z "USBi" interface to program a board with an ADAU1772 on it. I have a whole box of these board, produced with a pick and place machine. I have been pulling my hair out
-
31 band Graphic EQ
Does anyone have any thoughts on the best way to create a 31 band Graphic EQ? I am using the ADAU1452 and have currently done one with the Second Order, Double Precision, Parametric EQ but this only s
-
ADAU1761 PGA input noise
Is there a specification for the equivalent input noise of the PGA (differential mode)? If not, can someone with an eval kit measure it for me, say at +20dB and max gain? Thanks! Audio Signal Processo
-
SC584, ADAU 1979 configuration
Hi, I am new to ADSP SC 584 processor. I am trying to configure the A2B Master node and Slave Node on Eval board using TWI Communication. How can I configure the ADAU 1979 and ADAU 1962 registers. Can
-
How can I change the compressor limiter settings via the Aux ADC?
I love the compressor and noise gate blocks in SigmaStudio but I need to change some of their parameters using an external pot by using the AUX ADC. How can I get access to these blocks to pipe-in the
-
ADAU1701 SPI timing
I have been using a microcontroller for quite some time to boot the ADAU1701 in SPI control mode, download DSP code, and read/write parameters. This worked well at an SPI speed of 1MHz. We recently tr
-
single or double precision filter
Hi, The single precision filter has a ploblem. Examples are as follows. Here, f = 30Hz, Q = 1.41, Boost = 1dB 1. The level12 readback data is -48dB. I add a DC filter(DCB2), and the level3 read back i
-
ADAU1452 exposed pad not connected symptoms
I have a question regarding the exposed pad on the ADAU1452. I have assembled five boards with this part, and the DSP is apparently not running - it isn't even getting warm with power connected. I sus
-
How can obtain a Algorithm Designer?
In one of old SigmaStudio resales (3.7 if remember correctly), there was left in the installation the "Algorithm Designer" block, accessible trough DesignerNew.dll add-ins. It is very useful if someon
-
DSP Engineers, and where to find them?
Dear community, For a product my company is developing, we are using the ADAU1761 codec and two Wolfson MEMS microphones to eventually do speech recognition. Unfortunately, the audio quality received
-
RMS table in Sigma Studio
Hello On component RMS TABLE there is parameter called RMS TC. How this parameter influence the function . I have tried several values for this and didn't noticed any change in behavior. What are the
-
Polyphase Filtering in SigmaStudio
Hello, We have a System with a ADAU1442 DSP for a Loudspeaker and want to filter with FIR filters at lower frequencies. Is there a simple inplementation for polyphase filtering or for run a lower samp
-
How to access to the parameters values?
Hi all, I'm still in a stuck mode, trying to understanding the DSP world. I own a 21489 demo board. By the Sigma Studio I drawn a schematic and by the CrossCore ES I'm writing C code to control some i
-
Request for schematic review
I'm getting close to going out for proto boards. Can an engineer at Analog Devices (like Dave or Tyler) take a quick look at my schematic involving ADAU1761 and ADAU1452? Thanks! Ed Audio Signal Proce
-
ADAU1772 Sigma Studio script tool not working
I am trying to use the script tool to control a dB Volume Slider value for the 1772. Here is the schematic and script I'm using: When I run this script, the slider value does not change. I ran the sam