EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Can't set GPIO after performing safeload.
Hello there, how are you? I am developing an application with PIC32 + ADAU1701. I am running short on IO pins of the PIC32, so I decided to use some of the MP pins of the DSP as outputs to expand the
-
Can I run ADAU1701 and AD1938 codec at different sample rates?
I have an ADAU1701 clocked by a 12.288MHz oscillator, which I am running at the 48kHz rate for the on-board DAC and ADC. I have a AD1938 codec with serial data pins connected to the ADAU1701. The AD19
-
ADAU1761 INPUTS
Good day, dose the input block in sigmas studio represents the inputs on the (ADAU1761),for example, input 1 and 2 is linked to in put left of the (ADAU1761) and input 3 and 4 of the input block in si
-
Envelope Generator (ADSR) block for ADAU1701
Hi Guys, an Aida DSP user builds analog synthesizers, he is curious about the possibility to use ADAU1701 to realize some of the common blocks found in popular old analog synths. One of the building b
-
How to set the clkout sync with BCLK on ADAU1451?
Hello Guys, I have set the CLKOUT 12.288Mhz and Fs is 48kHz. However, my salve device can't accept MCLK is not sync with BCLK situation. How to set MCLK sync with BCLK? By the way, the offset of MCLK
-
Several adau1701 and E2prom in the same SigmaStudio project
Hi I am working on a 1701 project and i would like a confirmation that my concept is doable. Lets say that i have an I2C bus with two 1701 , two E2prom and an MCU, all in different addresses . Can i c
-
ADAU1452 DM0 delay issue
There is a problem in the way sigmastudio allocate DM0 memory for DM0 delays. Here is an example schematic: It's a simple DM0 delay and a simple DM1 delay. Here is the modified and commented compiler_
-
Recommended land pattern for ADAU145x?
Surprised it isn't on the datasheet. Is there a simple drawing of a recommended land pattern available?
-
ADAU1450 - production programming tools
Hi, Can someone suggest me some production programming tools for ADAU1450? TKS Best regards Patrizio Audio Signal Processors adau1450 SigmaDSP Audio Processors
-
What is the proper way to use the beamforming block with more than 3 microphones?
I am using the Griffith's Jim Beamforming block. I would like to use it with a linear array of 6 microphones. This post SigmaDSP Two Microphone Beamformer implies that the block can be cascaded, but I
-
Set Reset Edge Triggered Latch
Hi . I Need a method to Set a LATCH to "0" when Signal A goes below an adjustable threshold. and only reset it to "1" when a Different signal Goes above a Different threshold. The problem I appear to
-
SPDIF/SRC freezes on DC offset
I have a problem using the SPDIF input through SRC. When the SPDIF source is removed one or other freezes on a random DC offset value. In my design this is passed through to the output which is drivin
-
Adaptive FIR Fx-NLMS, which evaluation board?
Dear Community, I would like to implement an adaptive FIR filter with 1024 coefficients, to be updated by a normalized, filtered-X LMS algorithm (Fx-NLMS) at a sample rate of 2 kHz. For this, I am loo
-
Is it possible design FSK modulator/demodulator on SigmaDSP?
Hi All I would need design about 2MHz FSK modulator/demodulator with analog input/output on SigmaDSP processor. Is it possible? If yes, where is starting point of documentation like hardware manual, s
-
Mux slew rate change Sigma Studio
Hi guys, I'm controlling a mux with slew rate with a microcontroller and I wonder if there is a way to change its ramp time. I'm using Muxes/Demuxes->Multiplexers->Switch->Clickless SW Slew->1 Ch. Not
-
DSP Evaluation Kits - High Sampling Rate.
Hi, I am working on a prototype of an Ultrasonic device, using the ADAU1701 evaluation board. Due to the updated requirements, I am currently interested to test several Phased Array algorithms. As a r
-
USBi controlled outside Sigma Studio
Can I control the USBi (ADUSB2Z) board using my third party program (windows c# application), and NOT SigmaStudio... This is intended to work after DSP is programmed by Sigma studio. I, then, close th
-
I have a Question about Peak Room in Limiter
Hello everybody~! I have a Question about Peak Room in Limiter ADAU1452 Limiter is have peak Room? if Limiter is have peak Room What is peak Room value in Limiter? help me... Please..... [My test resu
-
About compressor parameter setting
Dear Sir/Madam, I use a MCU to control the adau1452 thru SPI interface. I want to know how to calculate the parameters of peak and rms compressors. For example,I use a RMS full range compressor,how ca
-
SigmaSudio connection to Sharc Evaluation board fails
Hello I try to Link CompileDownLoad ADI examples or my simple designs using SS3.12 to Shard Eval boards (with 489 and 469 Sharc processors). I choose related loader and boot target in Config Tab. But
-
ADAU1442 , ADAU1452 setting issue on Sigmastudio
Hello, My customer ask ADAU1442 , ADAU1452 setting issue on Sigmastudio. 1, ADAU1452, using selfboot mode, I advise engineer as below step to export files from DSP. Now customer export hex and bin doc
-
Prepare LDR file after using SigmaStudio for SHARC
I am using SC589 EVK and sigmaStudio for SHARC to design the audio signal flow. I want to know (1) how i can prepare the LDR file that need to be program to the SPI flash. (2) On the SC589 EVK, what p
-
Change USBi to ADAU1452 comms from SPI -> I2C
In hardware Configuration window of the project, USBi automatically selects SPI 0x1 ADR0 for ADAU1452. But I would like to change it to I2C. When I use drop down menu to select the range of available
-
ADAU1452 and SigmaStudio - Loops and Subroutines?
I'm planning to implement four instances of an audio chain in the ADAU1452 (along with two ADAU1961 or ADAU1761 codecs). Some aspects of the four audio chains will be identical, like certain FIR filte
-
Automatic EQ Impulse window Not Initialized
I'm currently working on a project with an ADAU1701 board. I recently posted about a Comm Failure issue but using a different computer seems to have avoided that. Now I'm trying to utilize the Automat