EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1451 I2C data hold time
Dear Sir, According ADAU1451 datasheet description as below: But it's seem against the I2C spec. description as belo Our customer use 400KHz I2C, datasheet define “data hold time is >= 0.9us”. But I2C
-
about a code compatibility on SigmaDSP
Hello all, I have a question about a code compatibility. I created a project file on Sigma Studio ver 3.11. And now I am trying to run the project file on Sigma Studio ver 3.12. But I doesn't run on i
-
Comm Error
All, I've been using the ADAU1701 processor in a couple different setups, all are based on the FreeDSP layout. I have recently been getting intermittent (say 90% of the time) "Comm Error" messages whe
-
Comm Error
All, I've been using the ADAU1701 processor in a couple different setups, all are based on the FreeDSP layout. I have recently been getting intermittent (say 90% of the time) "Comm Error" messages whe
-
About compressor parameter setting
Dear support team, I use a MCU to control the adau1452 thru SPI interface. I want to know how to calculate the parameters of peak and rms compressors in sigma studio. For example,I use a RMS full rang
-
ADAU1761 DIGITAL MIC ISSUE
We meet a issue at ADAU1761 digital mic application. I have build a project recieve digital mic signal successful, but I found the DSP have recieved two channel signal while I just connect single PDM
-
Adau1451 problem with the analog volume control.
Hello , the problem lies in the analog volume control . Made processing SigmaStudio 3.12 as follows: https://ez.analog.com/cfs-file/__key/communityserver-discussions-components-files/396/3652.7aeb9cb6
-
ADAU1761 boot from uC
Good morning! I've been attempting to boot a ADAU1761 dev kit using a Cypress PSoC5LP dev kit, but have had no luck. I'm following Wilfrido Sierra's tutorial, <How do I create the microcontroller code
-
ADAU1772 IBIS model - is there an updated version being released?
Hello ADI Tech Support, The IBIS model for the ADAU1772 is missing a lot of the parameters that the Cadence Sigrity tools expects. Is there a new IBIS model in the works for the ADAU1772? Thanks, Chri
-
Problems with SW connection Sigma Studio to EVAL-ADUSB2EBZ
We face a problem with an eval board (EVAL-ADUSB2EBZ) at the moment. When starting sound setting in Sigma Studio, the data transfer is working, which is shown by the blinking yellow LED. Afterwards th
-
DSP monitoring register
Hi, Is there a default method to monitor if a sigmastudio DSP (e.g. ADAU1452) is running properly after booting (via I2C)? I would assume (or hope for) some register that indicates the DSP is properly
-
ADAU1452 Eval @ 96 or 192kHz
I'm investigating the use of the ADAU1452 for a 96kHz or 192kHz project, and am wondering if the eval board would be helpful, given the (baffling) restriction that the CODEC is stuck at 48kHz that's b
-
Question about using custom code to program the ADAU1452
I have the EVAL-ADAU1452MINIZ and am hoping to be able to run custom code on it. It seems like running the code directly through SigmaStudio is not possible. I was wondering if the export system files
-
MTK platform + ADAU1722
Hi, We have a new design, MTK platform, end product is headphone. If audio quality issue, want to add a codec/DSP(ADAU1772) to do some algorithms. But MTK i2s output have huge jitter, on 64fs@48K samp
-
Maximum number of DSP 'streams' (input/output)
I remember reading that at least some of the processors (1701?) could only handle four DSP streams, even though there were more than four outputs available. Is this the case with all DSP families, inc
-
Data format to ADAU17x?
I'm sure this is an easy one but I'm not finding the answer by searching for it. I have an application that uses an I2C connection from a SiLabs Gecko to send DSP configuration stuff (I had asked a qu
-
ADAU145x Superbass
Hi, working on a 1452 device running at 192kHz. Start pulse is set to Base_FS x 4 and system sampling rate is set to 192kHz. MCLK is 24.576MHz, pre-divider 8 and feedback divider 96. SigmaStudio Versi
-
ADAU1772 48KHz processing by underclocking?
I have some questions regarding sample/clock rates in the ADAU1772 with the goal of processing audio at a 48KHz sample rate and connecting bi-directional audio on the serial port as a slave at 48KHz,
-
ADAU1452 clock generators - How to choose N and M
I'm using a 12.000 MHz oscillator input to ADAU1452 XTALIN/MCLK, and need to operate at 32.000 kSamples/second. With Divider at 4 so Input to PLL is 3.000 MHz, and Feedback Divider at 96, so System Cl
-
ADAU1452 stand alone - operate without a PC
Processor: ADAU1452 I am using the Evaluation board EVAL-ADAU1452MINIZ. My code has been saved in EEPROM for self-boot operation. So upon Power-up or Reset, it starts running the code successfully. Ho
-
[Bug Report] Sigma Studio FIR filter crash
When loading large FIR filter tables from external txt files in SigmaStudio (I've tried e.g. 4096 and 8192) the program stops responding and reports a crash after a long time (many minutes). I've trie
-
Need help on energy based selector/mixer
Hi, I have two analogue mic inputs. One is a noise insensitive mic with a bad frequency response and one is a conventional mic. The application is speech transmission. The noise insensitive mic will b
-
Question about H/W accelerators
Hello all, I have a question on a line below. (chapter "Hardware Accelerators" on the data sheet p.78/180.) "The slew accelerators provide for click-free updates of parameters that must change slowly
-
VCO Phase Control/Modulation on ADAU1701
Hello all, is there a way to control the phase of a VCO block, in order to have PM (Phase Modulation)? Right now, I am able to create projects with FM which are working perfectly but I would need also
-
Sigma Studio - Dynamics and time constants (ms vs dB/s)
I am developing an app using ADAU1452 and Sigma Studio. I am using a Compressor block (for rms and peak compression/limiting). I have seen time constants are in "dB/s", but i would like to work with "