EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Impedance matching issues
Hi, I have a ~5V PMT output that has frequency components ranging from DC-30 kHz. I want to get rid of the frequency components from DC-10 KHz. So I am taking this PMT signal, terminating it with a 10
-
SigmaStudio gave 'reserved' value for Register bit field...
Version 3.11 Build 2. Rev 1396. Added ADAU1372.dll to C:\Program Files\Analog Devices\SigmaStudio 3.11\. Started new project, dragged ADAU1372 device into workspace, made many changes under various ta
-
Can we embed a 'dumb' parameter into the ADAU1701 code?
I would like to be able to pass a number into the ADAU1701 through the self boot code. I would like to be able to use a library cell like interface read/write where I should be able to enter the code
-
ADAU1761 -- Beamforming with Wind Noise Reduction
Hi, I got one customer doing BT Handsfree in the car environment. They have encountered one issue whereby the BT handsfree module is mounted below the air-con blower in one of the car model. They use
-
SPi slave port
Hello I want to design some sigma dsp project. In this project external MCU should write data to the spi slave port of sigma dsp (adau1450). For some reason I can't find a spi slave block in the sigma
-
ADAU1772 Filter Response Issues
I designed a 8th-order filter in Matlab and transform it into the SigmaStudio.In order to get the 8th-order filter I use four 2nd-order filter as follows. The response of filter get from the Probe hav
-
Popping Noise
Hi ADI Eng We used ADAU1701 as a DSP processor for an amplifier (80&200W) design, we heard popping noise when real-time adjust the shelf knob. We have tried two different DSP designed-block in below,
-
Self-boot from EEPROM with address lines not set to 000
Hello, By default the ADAU1701 eval board connects to the on board EEPROM whose A0-A2 lines are all tied LOW. On a custom board, is it possible for the ADAU1701 to 'self-boot' from an EEPROM whose A0-
-
ADAU1701 DAC clock driven from PLL or MCLK ?
I have a ADAU1701 design with the MCLK driven from a dirty clock from a spdif receiver. this affects the noise floor of the DAC severely. I hoped that I could clean up the DAC clock by decreasing the
-
ADAU1701 Filter Latency
hi guys I need your help. I designed a digital filter by Matlab and load the transform function parameters into the ADAU1701 board.The curve simulated in sigma studio is right,but I test the board use
-
ADAU1461 standalone
Hi, ich versuche mal meine Frage auf Deutsch zustellen. Ich Versuche mit dem ADAU1461 einen kleinen DSP-Amp zu bauen. Ich bekomme das Teil oder die Kommunikation nicht richtig zum laufen. Und habe irg
-
USB to I2C to communicate to ADAU1701 via SigmaStudio
Hi All, My EVAL-ADUSB2Z has stopped working so I was looking for USB to I2C options and found a number of different affordable options that provide USB to I2C communication. Can I use these to use Sig
-
In ADAU1452, Is Burst write a method to implement safeload mechanism or does it have any other use case?
In ADAU1452, Is Burst write a method to implement safeload mechanism or does it have any other use case? Audio Signal Processors adau1452 burst SigmaDSP Audio Processors safeload
-
Looking For External LED Array Driver
Hello, We want to use the "External LED Array Driver" in our design. Is it suit for ADAU1442? Could you please help to let us know how to get this driver model. Thanks. Audio Signal Processors adau144
-
Clock failure cause ADAU144x malfunction
Hello, i've noted that interrupting the system clock to an ADAU1442 can cause, as written on the datasheet, an unpredictable behaviour. Mostly i get the audio data outputs frozen, so bclk and lrck are
-
ADSP-21369 vs ADAU1451 sigmastudio
At the same clock speed is there any practical difference between these type of chips. as far as Sigmastudio goes. I.E. at 48K sample rate can the Sharc processor doing floating point, handle a bigger
-
ADAU1452 and AES3
Hello Community, we have a product that utilizes the ADAU1452. It would be a nice feature to have AES3 support, although it is not a main objective. The datasheet of the ADAU1452 states specifically t
-
Eliminating Crosstalk
I have an application that involves the removal of one audio signal from another. I know this is often referred to as 'Source Separation', however my application is a bit different. Source Separation
-
Faulty frequencies in Sigma Studio
I have chosen Fs to 48 kHz. All filters in the Sigma Studio have actually a frequency that is four times the value. A filter at 250 Hz has really a frequency of 1000Hz. So I switch the Fs to 192 kHz.
-
adau1761 capture sound from I2S to DSP
Hello! I want to capture sound from I2S to DSP. In the SigmaStudio like an input I use input 2 and 3. And out to DAC0 and DAC1. I can hear sound from I2S on the speaker. I want to know- which register
-
Bypass an Filter
How i can select an Bypass (realtime) to hear and compare the result with and without ADAU1701? Audio Signal Processors SigmaDSP Audio Processors adau1701
-
multirate processing?
Hallo, in the Release Notes of SigmaStudio "Support for multi-rate signal flow" is stated since 3.12.0 Beta. Where can i read more of this feature? with Regards ropf
-
Recording the output of ADAU1701.
Hello, I am working on a project using the SigmaDSP ADAU1701 evaluation board. After processing the signal(@60Khz) using the platform, would like to post process the output using Matlab. What is the s
-
ADAU1452 code download
Dear Sir, We are starting a project with ADAU1452 Dsp. Now we encounter a problem when we down the Dsp code(which from export file) through the external MCU. The system is setuped by ADAU1452 DSP and
-
Can I use the "Capture" feature of SigmaStudio without an eval board?
Reading a PDF of instructions for how to use the sequencer window, it seems that running link-compile-download should populate the Capture window with commands from the programming process. When I per