EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1452 - error in DM0 bank 3
Hello, can someone explain to me what it means "error in DM0 bank 3"? Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
ADAU1772, how should we deal with unused pins ?
Hi, Please let me confirm below. If we don't use following pins on the system, how should we deal with them ? 1. DMIC2_3/MP5 and DMIC0_1/MP4 pins On the data sheet and reference board, these pins are
-
ADAU144x MP pin initialization glitch
Greetings! I've been observing the MP pins of the ADAU1445. It seems that no matter what mode they're set to (in a program stored to EEPROM for self-boot), they always pull high for ~100ms when the de
-
Can someone help me?
Hello Everyone,Please look at pictures My computer is Windows 7 64 - bit systems, when I install sigmastudio to this error, can anyone tell me?
-
How to do a Line/Mic Gain adjust in SigmaStudio
Hi, I'm using an ADAU1701 and have a line\mic input feeding one of the ADC inputs. I'm using a rotary potentiometer that is being read by one of the Aux ADC inputs. I would like to use this as a gain
-
Powering down DAC in ADAU1701
Hi, Is there a way to power down the DAC in ADAU1701 without having to control it with a host microcontroller. In my application I'm using the ADAU1701 in stand-alone selfboot mode with no host microc
-
Request ADI Surround for ADAU1701
Hello, This was requested before and it was said that the algorithm takes too much resources to fit in ADAU1701. However, is it possible to port the algorithm without the EQ (Jazz, Movie, Rock etc.) a
-
What could cause of ADAU1451 BCLK jitter?
What could cause of ADAU1451 BCLK jitter? The ADAU1451set for external 24.576MHZ clock. Output port OUT0 set for 512 BCLK sample (TDM 16 channels). CLKOUT has no visible jitter. PLLFLT voltage is 2V w
-
Controlling compression curve of RMS(gain) in ADAU1442 via microcontroller
Hi, I'm using RMS(gain) component inside SigmaStudio to design my project. What I'm trying to accomplish with this component is: There is some stereo input which is the main source and is normally out
-
ADAU1701 Param update
Hi, I have setup a simple project that outputs mono audio + 19kHz sine tone on ADC1. I have correctly setup the systems samplerate to 192kHz. Audio and 19kHz outputs just fine untiI I try to change th
-
How to configure three SPI slave devices with the ADAU1452 master control port?
Hi! I've designed a PCB centred around the ADAU1452 DSP. There are two TI PCM1865 ADC's tied the TDM inputs and a Cirrus CS4385A DAC connected to the TDM output of the ADAU1452. The ADC's and DAC's ne
-
Strange behaviour of ADC1 on Adau1701 (causing 48K <> 96K switch)
I'm having a very strange behaviour of ADC1 on an Adau1701 standalone board that I designed. The 1701 runs in MASTER mode, so it generates the clocks (BCLK and LRCLK). The MP3 pin of the chip is used
-
SigmaStudio AVC "Freeze" not working
Hi I am trying to use the AVC block on a ADAU1761 .All works fine, except the Freeze. When the input signal is muted. The gain is still increase to the MaxGain Setting. Regardless of the Freeze Settin
-
ADAU1451WBCPZ DSP PLL Lock
For our new design we’re using the ADAU1451WBCPZ DSP. Unfortunately I ‘m experiencing PLL lock problem. The PLL lock way form shown below: We’re using external clock 24.576MHZ for the 16 channels outp
-
2 supported files for Sigma Studio
Dear Sir/Madam, Our customer had got the following software from you. ADI_SigmaStudio-Rel3.11-x64.exe ADI_A2B_Software-Rel11.1.0.exe But he could not find the following additional file and document on
-
Component request: Delay processing block with milliseconds (not samples) parameter
Hi everybody, is there the possibility to ask the team to develop a block of delay with the parameter expressed in milliseconds and not in samples? The question can seem strange, but it would be very
-
Normalizing dynamic range of 12 bit AUX input to match 24bit codec audio
Hello Dave - or other SigmaStudio oracles My design is built around an ADAU1452 with two AD1938 codecs for audio I/O. This part of my design works fine. I've also routed two of the AUX ports on the AD
-
Using GPIO to setup external hardware - how to?
Hello Which block should I use to setup constans logic value on GPIO configured as digital output? I need this for change external hardware config for example shutdown pin. A
-
Beginner: Adding external Ram to Processor in SigmaStudio
Hi I am a beginner to DSP/Programming. I am very interested in using the sigmastudio compatable processors such as the ADAU1452 and ADAU1450. Is it possible to use external ram from within sigma studi
-
Which processor is best for implementing the Adaptive filter Algorithm
Hello, Which Processor is best for implementing all the different types of Adaptive filter Algorithms for Noise cancellation like: - Wiener Filter - Recursive Least Squares (RLS) - Least Mean Squares
-
ADAU1701/1401 I2C addressing AFTER selfboot sequence
Dear friends! Still fighting with my super slow multi adau1401 project and here's my question. I'm trying to develop a board with 2 ADAU1401s and I want them selfboot separately from each own EEPROM.
-
ADAU1442 TDM4 no data output
Hello I try to use ADAU1442 with PCM4104 DAC with TDM4 (I2S) interface, but I have problem with serial output interface - no TDM Data on SDOUT8 pin. ADAU config: Xtal=24,576MHz PLL0,2=GND PLL1=VCC (3.
-
I'm interested in datasheet ADW80011BSTZ and ADW80012BSTZ
Unfortunately I couldn't find information about the chips.
-
Matlab code to SigmaDSP
Hello , I have written Adaptive filters algorithms in Matlab, is it possible to make it compatible to SigmaDSP? Thanks in advance, Vidhya
-
SigmaStudio AUTO EQ Error
When Sigmastudio update to Version3.12.3, found Auto-EQ as new module add in ADI algorithm box. But it runs error after compile a sample project, analog input --> Auto EQ --> output, both error in ADA