EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
How to use the Sigmastudio to design a medium-frequency EQ by using the external potentiometer control?
Dear Sir/Madam, i am using ADAU1702. I need to design a medium-frequency EQ , you can use the external potentiometer adjustable frequency range 240Hz-6kHz,boost can enable external potentiometers for
-
ADAU1761 - MicroControler - Index Selectable Filter problem
Hi everyone, I program my DSPs using a microcontroler for bootup. When I try to select my Filter ( in the Index Selectable Filter block) with the index using a DC source, the index 0 and 1 work fine b
-
I need to implement adaptive filter algorithm in EVAL-ADAU1401AEBZ. But does not have nlms block. Please suggest how to start with it as I am freasher in this field.
I need to implement adaptive filter algorithm in EVAL-ADAU1401AEBZ. But does not have nlms block. Please suggest how to start with it as I am a fresher in this field. Thank you in advance. Vidhya
-
Calculate Coefficients of Chebyshev and Notch-Filters
Hi everybody, i have a question about the calculation of Chebyshev or Notch cofficients b0, b1, b2, a1 and a2. Where can i find the calculation? I've been looking in the SigmaStudio-Help but i found n
-
SigmaStudio for ADAU145X
when the multiple bands level detector component of ADAU145X can be add into Sigma Studio ? Is there any component that can set the Slew rate up/down Gain independently?
-
Sync SPDIF Tx rate to SPDIF Rx rate
Hi, I am planning a new product to use a SigmaDSP, the majority of the input/output will be analog (8 channel TDM converters). I will also use the SPDIF input as an extra stereo channel and I want to
-
How to change Input's active channels programmatically?
When we create Input cell it has only two active channels, but we need four input channels. How we can do it? I think, we should use "setControlValue" ss.ObjectSetProperties("setControlValue", "Input1
-
Create objects via ISigmaStudioServer
Hello! Can you help me with my problem? I want to create objects hierarchy programmatically via ISigmaStudioServer. But, INSERT_OBJECT has following signature: bool INSERT_OBJECT(string objectTypeName
-
How to terminate an unused input in SigmaStudio schematic
Hi, I am working in designing a schematic in Sigmastudio based on ADAU1761. There are some components needing several inputs for working, however, if we are just using part of its functions, then some
-
Map Pot rotation angle to index filter curve selection
I'm using an 11 detent pot to select filter curves. As you may know, the first detent above full CCW or below full CW is only a small change in resistance, much smaller than the other steps. I need to
-
Caution Regarding the Sigma Feedback Module (w/ a happy ending)
This ‘bug,’ or whatever, reared its ugly head during the development of a monaural audio processing system. These notes reference the ADAU1701 Development Board running under Sigma 3.11. Results descr
-
Information about Filter Type in Export Files
Hi everybody, i have a question about the export files. I want to recalculate the parameters Frequenc1, Boost, Gain1, Ripple etc. of 2nd Order Filters by using the coefficients b0, b1, b2, a1 and a2,
-
ADAU1451 - memory load verification
I am working on a project with ADAU1451 and need to verify if program and parameter memory are loaded correctly. Interface is SPI, speed is 2.625 MHz, mode 3. I am trying to read the memories after wr
-
Which is the latest Evaluation Board?
I have a Evaluation Board EVAL-AD1940MINI, need to know which is the latest, for my thesis at the University of DSP.
-
ADAU1442 and linux network stack (TCPADAU1442)
Hello, we are using the ADAU1442 in an embedded system and want to control the chip / unit via TCP and Sigmastudio using a TCP communication protocol. We are also using the ADAU1452 and want to do the
-
About ADAU1452 self-booting from E2PROM in I2C mode.
Hello, I have a question. I am creating my own board using ADAU1452 I am trying to self-boot ADAU1452 from E2PROM in I2C mode. At the same time I am using USBi. Can they use the same I2C line? Thank y
-
Custom IIR block on Sigma Studio
Hi everyone, I wish I could have an all pass filter block with voltage control on frequency on Sigma Studio Library for a guitar phaser project with Aida DSP. So I've made a 1st order IIR filter path
-
1452eval board as TDM slave?
I'm looking to interface an XMOS AVB endpoint with an adau1452eval board. The goal is to get 8 channels of audio into the dsp from an AVB link. It seems that my only option is to use TDM8 with one of
-
ADAU1452 SPI burst mode writing, wait time between successive word
Hi, The ADAU1452 SPI burst mode writing, should we add wait time between successive word transfers ? In the initialization sequence, when the host writes data via SPI in the burst mode, the ADAU1453 d
-
ADAU1701 Processing Latency?
I need some info on ADAU1701 Equalizer that I could not find in datasheet. Also I'd like to get eval board for that chip, i think it is EVAL_ADUSB2EBZ. the info that i'm looking for is processing time
-
ADAU1701 max ratings/protection on adc
Dear all, i'm using the adau 1701 with an 18k external serial resistor for the build in ADC, resulting in a 2V RMS input to the specified 100µA input fullscale. What happens if i would give more than
-
Will there be a Voltage Controlled Delay for ADAU1452 DM0 and DM1 available ?
Hi Analog, I often work with the Multitap Voltage Controlled Delay Block. In the ADAU1452 there are now 3 types of delay available: DM0, DM1, External SPI. Only one of them is available as voltage con
-
Problems with ADAU1772
Hello, I have finally received prototype PCBs for a new design using ADA1772 and ADAU1446. The DSP chip is acting as the master and providing the MCLK for the CODEC. In attempting to setup the signal
-
Powering down ADAU1761
Hi all, we have a project using ADAU1761, and we need to power it down to the mimimum when the device is "off". As our current design cannot shutdown the power, we are forced to use registers etc to a
-
Re: ADAU1452 Dolby/DTS
Hello Dave, my customer has a 5.1Ch input source and will like to pump into the EVAL-ADAU1452MINIZ via S/PDIF. However 5.1Ch input source being an encoded signal source (and not already in Dolby/DTS f