EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Eval - ADAU1701MINIZ global phase issue
Hi analog-admin and @Bob, The Eval - ADAU1701MINIZ works great!!! and the latency is 130 as @Bob explained me But , I am trying to add a global phase to the filter of 40 degrees but unfortunately coul
-
Global phase in Eval-ADAU1701MINIZ
Hi , I am working on a audio project with Eval-ADAU1701MINIZ sample rate 192kSamples How can I add a constant global phase to my card(lets say 30 degrees)? Is there some filter or other unit that does
-
External ADC/DAC on ADAU1701 - minimum required components
I'm wondering if I want use external ADC and DAC on ADAU1710, is it possible just keep the pins for FILTA, FILTD, CM, ADC_RES and ADC itself unused - or have they other function what it makes necessar
-
Having trouble with the Gain-Out Compressor
Hello, The new Gain-Output Peak Compressor is a welcome Toolbox addition. Although I've obtained a similar function by subtracting "before" from "after" signals around a standard compressor, this meth
-
The Nth Order Filter
This filter has shown up unceremoniously in recent SigmaStudio betas, and it's immensely useful. Previously, to make a sharp filter we had to cascade a number of first and second-order sections, Their
-
Concerned about crystal/clock swing level/ ADC noise issue.
Hello, I'm slightly concerned that the amplitude of my clock signal is too great. Attachment 'PIN41_27PF' shows the signal at pin 41 of my ADAU1446 (after the 100R resistor), measured using an inch lo
-
problem with 24 dB headroom available inside Sigma DSPs
Hi forum, I am facing this problem when using an EVAL-ADAU1X61EBZ. The manual of the ADAU1761 clearly states that there is 4 bit available internally that provide 24 dB of extra headroom before satura
-
Communication failure with ADAU1446YSTZ-3A
Using Sigma Studio 3.11 with EVAL-ADUSB2EBUZ to communicate with my DSP2 chip. I get an error message whenever I click "Link Compile Download" in Sigma Studio, which I have attached. The EVAL board li
-
problem with coefficients when simulating Sigma first-order high pass
Hi, I am facing a problem with the coefficients of a first-order high pass filter in SigmaStudio. I am trying to simulate the filter in Matlab. In order to do so, I am using the formulas provided in t
-
ADAU145x - Standard RMS compressor independent L&R
Hi, I´m using adau1451 and sigmastudio 3.12.2 The standard RMS COmpressor with independent L&R input not working in LINKED mode in which case the greater signal of L or R will drive the compression. I
-
ADAU1452 Panic Flag
Hello, I am looking for a description of the Panic Flag Register (ADAU1452). Best regards Mathias Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
EVAL ADAU1772 communicating with FPGA
Hi I just purchased an evaluation board from the ADAU1772 and need a bit of help. I want to the use the ADAU1772 to communicate with a FPGA to transmitt the data from the ADC to the FPGA and transmit
-
About ADAU1761 Noise issue
Hello, Our customer is debugging the ADAU1761, now find some question, expect your better advice. When input I2S signal, Playback of input end, and drag the progress bar for next or above item. Some t
-
ADAU1761 - Signal envelope attack and decay in db/s
Friends, I need to get the RMS signal value and controle the attack and decay in db/s. The signal envelope works fine, but I can't control the decay in db/s just linear. I would like to know if there
-
analog output from EVAL-ADAU1701MINIZ is not passing
Hi, I am passing a sine signal 400Hz from with generator through the EVAL-ADAU1701MINIZ with no filter but can't get an analog sine signal as I expect I heard the D type output amplifier has a digital
-
ADAU1701 I2S IN-I2S OUT @ 96kHz
Hi all, I've been testing a platform that consists of ADC-DSP set-up with DSP as a slave to the ADC. The ADC feeds the DSP with I2S at 96kHz and a MCLK of 12.288MHz. PLL setting on the ADAU1701 is 256
-
ADAU1701 Sigmastudio Limiter questionings
Hello support, Recently I checked several posts of the limiter and the main ones that I was looking for an information to help my customer were: https://ez.analog.com/message/215580#215580 that has le
-
ADAU1761 - How filter coefficients saved in microcontroller after SigmaStudio export?
Hi everyone, I have been running into a lot of difficulties to simply make my algorithm work by booting from a microcontroller. I finally was able to have something more or less working. My algo has 2
-
ADAU1761 - How would you maximize Signal-to-Noise ratio for small acoustical signals?
Hi everyone, I need to measure very low Sound Pressure Level signals (range -15 to max 30 dB(SPL)). I have designed a very good pre-amp with differential connection to the DSP ADCs, I setted the gain
-
loudspeaker protection?
I've spent over an hour looking for an article, how to, design note or whatever on a topic that I'm sure I saw in the past few month somewhere on the ADI system. It was, I think, about using frequency
-
ADAU1761 and SigmaStudio
Hi all, I use ADAU1761 with a BF707 development board. I use the codec only like dac and work perfectly. I send my data and the dac play audio stream. Now I would like to use a feature of ADAU1761 DSP
-
ADAU1701 Limiter issues at 192kHz
Hi, I have a Sigma Studio project running on ADAU1701, including a limiter which works at 96kHz but there is no output at 192kHz. Are there restrictions on the Limiter in regards to clock speed? rgds
-
EVAL-ADAU1701MINIZ cant get the microphone signal
Hi, I am new with Analog Device and I am using the Mic + Real time plot display I am using sigma studio 3.12 1. when I pass a sine signal to the input from generator I get an output to speaker but not
-
how to insert c code in ADAU1701
Hi, I am trying to create an 5th Order IIR filter and I cant find it possible Does someone knows how to insert an IIR c code(or MATLAB code) in the software? thanks! Audio Signal Processors SigmaDSP A
-
latency ADAU1701
Hi, I am using Sigma studio 3.12 and EVAL-ADAU1701MINIZ does someone knows what is the minimum latency I can get in the card?from mic to speaker with no filter and how can I measure it in the best way