EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
compressor
Please see pictures, can you tell compressor threshold and the data relationship, my threshold change, how to calculate the appropriate data is sent to DSP ?We will develop the PC interface,thanks!
-
Hey i guys, i cannot program the eeprom?
I am trying to make a dsp guitar effect using elekator adau 1701 and arduino board. I was succesfull to setup the component which was instructed in the elekator product site. So, now i am trying to pr
-
ADAU1761 parameter changing *without* Sigma Studio
I have an application where the audio device will be taking steps to equalize itself. The current method we use as a demo is to use Sigma Studio (3.something) to adjust the sliders and generate compil
-
adau1452 avc block adjust freeze level and max. gain
How can I adjust the AVC block adau1452 with higher values for freeze level and gain level? The values that I can be set too low for me and I want to have a greater range avc. Or, there is also anothe
-
Adau1452 block numeric format resource
Hi guys, I just upgraded from the 1701 to the 1452, and an having to rebuild all my blocks. Is there a reference, by block, for what numeric format each block requires as input and produces as output?
-
plot microphone magnitude using SigmaStudio
How can I plot the input magnitude of a microphone that is connected to an ADAU1761 eval board? The stimulus and probe do not seem to be plotting the throughput data, just filtering/parametric type ch
-
32 Bit Audio with ADAU1442
Hi there, I have a modular system with an ADAU1442 as signal processor. I would like to use an ADC and a DAC with a bit depth of 32 Bit. I know that the processor con process 24-, 20- and 16 Bit Data,
-
FIR Filter coefficients for voice
Hi All, I would like to use a FIR block into a ADAU1761 for removing the background noise, how/where could I calibrate the right coefficients? A simple pass-band filter isn't enough because the noise
-
1701 Index filter missing 0 state from pulse counter
Hello, I'm having trouble with this index selectable filter schematic. Bob helped me make a pulse counter that will count up to a value, and once it reaches it, the next pin toggle it starts at 0 and
-
ADAU1381 - hangs after the settings have been loaded
Hi, My customer was able to get the DSP to accept the settings from Sigma Studio by manually creating the header files. Now he has a new issue: About 30% of the time thew DSP seems to just hang after
-
TCPIP1940 protocol specification
Hello all, is there a document describing the protocol being used by TCPIP1940? I looked to this page https://wiki.analog.com/resources/tools-software/linux-software/sigmatcp, but this is clearly not
-
how to realize Multiply Accumulate in SigmaStudio
hello everyone, I want to realize the function of VAD (voice active detection). In matlab, I use the model of Multiply Accumulate calculate the energy of a frame. However, I can't find the corresponde
-
Crossover performance
Hello, When there is no input noise after crossover is seen. The noise level keeps up and down. It occurs if only filter type is set to Linkwitz-Riley 48. n the signal path without crossover, noise is
-
adau1761 - initializing spi problem
I am working with ADAU1761, initializing it over spi port from a microcontroller. Initializing spi communication mode is done according to the datasheet (pulling CS low 3 times after power-up, or doin
-
Audio delay (0-160ms) problem with ADAU1761
Dear All! I would like to delay (0-160ms) on a differential sound line with ADAU1761. But when I tried to set more than 86ms, the Sigmastudio says the RAM address exceeds:4096. I read about it. I foun
-
Something dragging FILTD down.
Hello all, finally managed to get my ADAU1701 board sort of up and running and programmed! The problem is after around 10-20 seconds of being powered up the voltage on FILTD starts to get dragged down
-
Limiter with "Zero" attach time?
Hi Experts, I am encountering a serious problem in my sigma DSP project. Can I get zero attach time limiter in sigma studio for ADAU1701 ? There are 2 type limiters in sigma studio, one is RMS limiter
-
Hilbert transform for ADAU1452
Dear support team, I want to get a Hilbert transform for ADAU1452(like it for ADAU1401). Do you have a schedule of making it? If you don't have it, please tell me how to make it by standard modules, p
-
ADAU1452 Licensed Algorithm Support In Sigma Studio
Hi there, I have been using the Dolby Pro Logic II algorithm with the ADAU1442 in Sigma Studio. Recently I acquired an ADAU1452 and wanted to run the Dolby algorithm on this too. I have noticed in Sig
-
ADAU1701 working at 176.4K/192K with trouble
Hi all, my project is using one ADAU1701 to do audio processing. SoC play/decode audio file, output the CLK/Data, feed them into ADAU1701, and after the audio processing, ADAU1701 output CLK/Data to a
-
Up/Down Pushbutton Crossfade Control
Hi, I am currently using an ADC configured GPIO on an ADAU1446 to control a crossfeed block with a potentiometer. I would like to change this to a two-button up/down control with maybe 10 discrete ste
-
Level dependent filter
Bob should be able to hit this one out of the park. I just want t o switch between a flat curve and a curve with 20Hz high pass filter based on signal level. Should be simple right? A signal detector
-
SigmaStudio 3.12.1 available?
When will SigmaStudio 3.12.1 be available? Kind regards, ST
-
ADAU1761 i2s input limit
In the datasheet for ADAU1761, it is not clear to me if the following configuration would be possible: 1 analog input channel 1 stereo i2s input 1 mono i2s input 1 stereo i2s output What is an ideal i
-
Initialization sequence of ADAU1452
Dear support team, I have a question about hibernate bit(0xF400 0bit) in initialization sequence. In Datasheet P.26, "Recommended Program/Parameter loading Procedure" said that "When writing large amo