EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 reading RMS detect display value from uC
Hi all, in a project with ADAU1701 and SigmaStudio 3.8 I use a MONO RMS Detect (Display) block as limiter. I need to read the signal and compression levels from an external microcontroller. I didn't f
-
Turn on 2 digital mics and 1 analog mic simultaneously with ADAU1761
I would like to use 2 digital mics and 1 analog mic together with ADAU1761 to do active noise cancellation and echo cancellation by beamforming algorithm in Sigmastudio. However, base on my understand
-
Two technical issue in ADAU1451 application: I2S in slave mode and SPDIF Tx can’t output 96KHz sample rate audio stream
Dear Experts. Our customer is choosing ADAU1451 in the new design, and they met two issue in ADAU1451 application, would you please help to check and give some advice how to fix the issue? 1, There ar
-
adau1452minz with SigmaStudio 3.11 loading eeprom
Using ADau1452minz and SigmaStudio 3.11 build 2 rev 1396. The adau1452 is amazing, and SigmaStudio is a very easy to use GUI. My project is sounding great!!!!!!! However, I have been unsuccessful at d
-
EVAL-ADAU1701MINIZ Could Analog Devices please supply the Gerber files for this board
EVAL-ADAU1701MINIZ Could Analog Devices please supply the Gerber files for this board
-
Wake on Audio SIgnal with turn off delay
I'm using a Signal Detection block to turn on a GPIO for external amplifier enable. Need to delay turn off for 5 minutes or so after signal stops. 5 minute Counter should reset with every signal detec
-
1st-order filter implementation question
Hi forum, I was wondering if there is anything wrong with the definition of the first-order filter in the help of SigmaStudio. I found the following definition for the first-order filter: However when
-
1452 with several ADC and DAC
Hi, I would like to connect several ADCs and DACs to the 1452, i will use all of them at the same clock frequency (48kHz) in I2S format. I would like to use the 1452 as a master clock for ADC and DAC.
-
How to switch between analog and digital inputs on 1701 using SigmaStudio
I am doing a project that requires GPIO based selection of digital I2S audio and analog audio input using SigmaStudio. DSP ADAU1701 self boot mode. I'm new to SigmaStudio Audio Signal Processors Sigma
-
Very Low Freq Noise when summing D/A outputs 1701
I only need 1 output so I used an inverting summer to add all the D/A together for better noise. Works at HF but I have a very low frequency flicker noise that comes and goes. Mute does not affect it.
-
stuffing SigmaDsp readouts into one integer
Hello everybody, i have to transfer some readings out of the dsp, but would like to limit bus traffic, so i was thinking i could stuff more readings into just one integer (i don't need the resolution
-
It's Pi Day -- Compute the approximate value of Pi with SigmaDSP
Engineers have a bad reputation for abusing things. For example, power supply magnetics designers often abuse (and sometimes blow up!) audio power amplifiers to test their wound components at odd ampl
-
SigmaStudio 3.11, issues with ADAU1381 sound engine
Hi, I have a project using ADAU1381 and need to generate the Sound Engine parameters for my application. I am using SigmaStudio version 3.11 along with the project provided in this Wiki Link: https://
-
Why does the blinking led example in AN-951 not work?
I am trying to get some custom hardware up and running and the blinking led example does not work. I can manually toggle the output pins by using the read/write registers tool but I cannot generate th
-
Simple question, whats the name of this T element and where do I find it
I was reading this note on how to use the compressor function, but it uses a T element to split the input into two. One goes to the audio channel the other the control side. I just don't know what the
-
ADAU1442 I/O channel truncation
Hi, we have an application where we need to interface 11x I2S lines and 1x TDM8 to the DSP (in and out). However, the TDM8 stream only contains two channels in its first 2 slots. Its other 6 slots are
-
ADAU 1761 control output volume by input
Hi, I am hoping someone can point me in the right direction. Firstly my application is in the audio band obviously, but for a non audio application. I have my demo board up and running. I am using the
-
Peak EQ bandwidth
Hello, When I measured Peak EQ bandwith in sigmastudio 3.11, I got a result as shown below. The real bandwidth measured is not identical to the bandwidth calculated. Is it a bug of peak EQ module pack
-
ADAU1452 external delay
Hello, We would like to implement an external delay for 4 different audio signals. I have seen in one discussion that it was possible to do it if we design a custom block or if we add C code function
-
Questions about decoding by single microphone or double microphone
We use the ADAU1761 evelopment toolkit for a decoding project, but we find some questions. We need your help. Questionsdescription is as follows: Background: we use the ADAu761 development toolkit for
-
ADAU1452 FIR filter size and delay time
At this moment we are starting a new project and evaluating several DSP options, one of them is ADAU1452. We are planning using it but we have some doubts User manual shows that ADAU1452 can perform 2
-
ADAU 1442 big project
Hello! I was doing a big project on adau1442. After he won 66% of the resources have a problem with the distortion signals. I created a test project to test this problem. What could be the problem? Pr
-
ADAU 1451 slave i2c port trouble
I have a board which I upgraded from an ADAU1701, to an ADAU1451. The ADAU1701 was working perfectly I just needed more horsepower. I connected the part with i2c control, using the slave port which is
-
Click noise reading data from DSP
Hello, how are you? I am working on a test equipment with ADAU1442 + AD1939. Everything works good, except that when I perform any reading operation, the DSP clicks and pops. SPI is running at 500Khz.
-
ADAU1442 + AD1938 ADC Noise
Hi there, how are you? I recently developed a car audio signal processor using two ADAU1701s. Now I am working on the testing jig, which among the many tests it performs, it is supposed to measure the