EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Increasing ADAU1761 full-scale voltage range
Hello, I'm using ADAU1761, full-scale input voltage is 1Vrms. I'm using pseudo diffenential input and would like to extend therange to 3V. Is it proper to use only resistors before ADAU1761's differen
-
External delay in ADAU1452
Hello, I use Microchip SRAM 23LC1024 with ADAU1452. Now I have got a problem that when I use more than one external delay modules, an assembler error will come out. It's quite necessary for me to use
-
How can I make the ADAU1701 save the data after power down ?
I have a ADAU1701 eval board, and when I unplug the USB , I have to "run link compile" to reactivate the ADAU1701 How can I make the ADAU1701 save the data after power down ? Audio Signal Processors S
-
ADAU1761 strange I2S behavior
So I have an ADAU1761 that's been working pretty well, I have my filters and blocks all outputting to the headphone dac fine and everything sounds good. I started with a sample rate of 48Khz and have
-
Sigma DSP integration in micro controler - weird behavior
Hi, It's been a while I've been running into problems with the integration of my Sigma DSP with a micro controler. The problem is usually as follows: 1) When I try my Sigma DSP program real time using
-
Flanger module for Sigma DSP on Sigma Studio
Hi, I'm looking at Sigma DSP Wiki and found Flanger module on following site, but could not find the module on Sigma Studio. https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/adialg
-
Need help with dynamic programming basics ADAU1702
Hi, so I'm working on a project where I'm using a micro-controller to drive a display/menu system and program filter coefficients (using a 1702 based evaluation board) such as updating crossover, limi
-
USBi Required for 64 bit ADAU1702 EVAL?
Hello, I'm using the 1702 based EVAL board and I am having trouble communicating with the device over standard USB (using the 1702 communication channel I believe is for the board). I don't have the U
-
SigmaStudio V3.11 "Adaptive Mixer Dual"
Hello, I recently tried to implement a cross fade based on input threshold using the Advanced DSP algorithm titled "Adaptive Mixer Dual (graph)". When I had the DSP connected (link, connect, download)
-
uC vs. SigmaStudio booting a gaggle of ADAU1701s
Here's a second issue from a troubled mixer prototype. Posting my first issue resulted in some real help, so here goes: The mixer uses a dsPIC booting six ADAU1701s on two I2C buses (Snow White and ne
-
ADAU 1772 getting acknowledge after wrong subaddress.
Hello, In ADAU1772's datasheet it is written (page 41): "If an invalid subaddress is issued by the user, the ADAU1772 does not issue an acknowledge and returns to the idle condition." I have checked i
-
A -1701 FM MPX Demodulator
This is a just-for-fun project, for which no claims are made that it's optimal. I just drew it up in half an hour a few months ago, and then tweaked the thing until it worked. The incoming composite s
-
ADAU1701 General (2nd order/lookup) filter block sending two sets of parameters?
I notice that when changing the frequency value in one of these filter blocks, SigmaStudio sends two sets of parameters to the DSP; the old, then the new, to the same address. What is the purpose of s
-
Frequency Doubling
I'm using an ADAU144X at 192kHz in an application to double a 25kHz sinewave sync signal to obtain a 50kHz operating frequency. Multiplying the signal by itself and DC-blocking the output does the job
-
how to store a value on one of the interface registers of 1701
Hi guys, I am using a 1701 in standalone mode, with the use of an external EEPROM. I need to store some values in the interface registers of the 1701 so they can be written back to the EEPROM. After r
-
ADAU1772 is not working correctly after assembly programming.
Hello, I am loading ADAU1772 program in assembly following this tutorial: Booting a SigmaDSP from a microcontroller with no C compiler . In SigmaStudio I got project which is supposed to redirect inpu
-
Conference phone based on SigmaDSP
I am looking for idea of hands free conference phone where most critical issue is a feedback coming from loop between speaker and microphone. Are you able to provide any examples of removal of feedbac
-
ADAU1781 attenuates signal
I have an ADAU1781 on a board that I have designed. I am communicating with it over I2C from a PIC32. I seem to be able to set up the chip; however, after it is set up it greatly attenuates all signal
-
compressor parameters
Hi, I use 1452 on my target board.The compressor used is : Dynamics Processors->RMS->Standard Resolution->Lower Range(-90~+24)->Stand RMS.But I don't know how the parameters of the compressor calculat
-
micro-controller for ADAU1701 ?
I want to use a micro-controller to control the ADAU1701 , can you share an example I want to control a parametric EQ gain ,frequency Q Thanks Audio Signal Processors SigmaDSP Audio Processors adau170
-
Sigmastudio
Hi, My schema file is around 5 MB. I was saving it when Sigmastudio crashed (an exception raised) and closed. Now when I try to open my project, the tool crashs again and again. Is there any size limi
-
Can I program a RLS filter using SigmaStudio on a ADAU1401A (SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs)?
Hello all, I want to implement a RLS filter using the program SigmaStudio on a ADAU1401A. Is this possible? I don't find the right way to do it. Thank you in advance adau1401a Audio Signal Processors
-
wrong MCLK settings cannot initialise DSP
Hi forum, I recently tried to initialise a 1761 DSP codec. The Master clock settings were accidentally set to the wrong frequency, 12.286 MHz instead of double this number, on the DSP code extracted b
-
band limiter
hi forum, I am in need of a band limiter functionality in SigmaStudio. I need to limit/compress signals that exceed a threshold in a certain frequency range, leaving it unaffected when it does not exc
-
ADAU1452
What is the lowest frequency that is usable? The GUI refers to 20 Hertz. I would like to go from .5HZ to 20HZ. Is this possible. I am looking at creating band pass filters. Thank You, Philip Nielsen A