EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Crystal not oscillating-things to check?
So, I've built my first board but I'm seeing no oscillation on the OSC pins, what things can I check to find the problem? I'm seeing around 1V DC on the OSC pins, is that about right? I've followed th
-
ADAU1701 analog input and I2S input select
Hi, I am a beginner and I plan to use the ADAU1701 in an active speaker. I bought the ADAU-MINIZ development tool. In my design I would like to use an ASRC like the PCM9211 (Bluetooth with RN52 module
-
Can EVAL-ADAU1761Z be used to stream audio?
Hi Is it possible to set up the EVAL-ADAU1761Z (evaluation board for ADAU1761) using SigmaStudio and then stream audio to it from another PC application - e.g. play music through a selected output on
-
Audio filtering for radio communications using ADAU1700/1
Im working on a project that would benefit from DSP on transmit and receive in a radio communications transceiver. The test board we have, has 4 pots connected to 4 analog inputs. We want to use 2 cha
-
ADI Sigma DSP for echo cancellation
Hi, I am choosing a sigma DSP for echo cancellation project. Currently I am comparing ADAU1761 or ADAU1401A. May I know what is the Acoustic echo tail length coverage for these 2 devices? Thanks. adau
-
Internal impedance for ADAU1761and ADAU1401A BCLK port
Hi, Do you have any idea on the value of internal impedance for ADAU1761 and ADAU1401A BCLK? According the MEMs Mic application note that we received, we need to match the impedance between BCLK and t
-
ADAU1701: external frequency change detector
In my design (ADAU1701 self-booting) I have a switch that selects sample rate by changing an external oscillator's frequency. I need to generate a reset when that switch changes so that -1701 can load
-
How to upload the data from Sigmastudio unto the board I built ?
After building the board can you tell me how to upload the data from Sigmastudio unto the board I built ?, the schematics in the link dose not show any USB interface to the computer http://www.analog.
-
Too Much Noise in a SigmaDSP-Based Mixer
Hello, Our new mixer prototype described at https://ez.analog.com/message/165262#165262 suffers from noticeable output noise with its inputs turned down. To trace its source I modified the SigmaStudio
-
Which SigmaDSP Processor for my Application?
Hello, I need the following dsp functions in my new design and I started to wonder which processor would meet my requirements. I need at least two Linkwitz-Riley-Filters in 8th Order (48db/Oct) and at
-
1452 program¶meter ram
Hi, I use 1452 on my target board.In order to check whether the data 1452 received is right,I use the microcontroller to read the program ram and the parameter ram after sending the program data and p
-
COMPILER ERROR
COMPILER ERROR Edit Notes Added category and text to description [edited by: GenevaCooper at 9:54 PM (GMT -5) on 5 Jan 2023] COMPILER ERROR software
-
Booting a SigmaDSP in assembly (multiple bytes).
I am working with ADAU1772 and I got no Evaluation Board, I want to program my DSP using FPGA. I have read this tutorial: Booting a SigmaDSP from a microcontroller with no C compiler in FAQ but I stil
-
ADAU1702 hysteresis settings
I don't understand the auxiliary ADC hysteresis settings: FIL[1:0] 00 4-bit hysteresis (12-bit level) 01 5-bit hysteresis (12-bit level) 10 Filter and hysteresis bypassed 11 Low-pass filter bypassed S
-
ADAU1701 External Delay: Idle Thoughts on Boxing Day!
I've been experimenting with concepts of using the serial data outs for SPI control of other ICs, where an ADAU1701 is used in self-boot mode and there is thus no MCU. This is because my designs are s
-
Creating Windows program to control parameters
Hi, I am creating a DSP program that will reside inside a consumer product. Once the firmware is uploaded via SigmaSudio, I which to create a Windows program that allows for the user to only control c
-
ADAU1701 + S/PDIF in + I2Sin/out+ internal ADC/DAC + external DAC
Hi there, we are planning a small DSP board using the ADAU1701. Features should be: internal ADC (2 channel) internal DAC (4 channel) external S/PDIF receiver (maybe with transmitter to) external DAC
-
ADAU1761 I2C only works after programming device
I've done a bunch of work with my ADAU1761 board and now I'm ready to have my microcontroller program it. I've read the presentation/guide on how to do it from analog. My codec programs fine when I us
-
5.23 conversion sample code
Is there sample code for the conversion of 5.23 to the hex value(s) I have to write over I2C for my ADAU1761? I'm just getting into trying to program it from my PIC32 and I'm not really sure where to
-
5.23 Convert to Hex for I2C program of ADAU1761
Is there sample code for the conversion of 5.23 to the hex value(s) I have to write over I2C for my ADAU1761? I'm just getting into trying to program it from my PIC32 and I'm not really sure where to
-
ADAU1761_ About SigmaStudio
I have been tested using the EVAL-ADAU1761Z and ADUSB2Z. 1, I've saved the SigmaStudio project using the "Save as ..." . However, change information of Automatic Startup will not be saved as shown bel
-
EVAL-ADAU1442 GPIO with 96kHz
I am having trouble with the read / write registers for a volume control using the EVAL-ADAU1442EBZ board and GPIO expansion - everytime I turn off the device, the volume is reset to 0dBFS - the previ
-
Error while compiling for ADAU1452 under Sigmastudio
Dear all, I'm trying to develop an audio mixer application with ADAU1452. My project uses an input matrix (22x24), 12 processing channels and an output matrix (26x14). When I try to compile the projec
-
Writing to EEPROM 24LC16BT from USBi
In short, it's not working. Here are the steps I've taken Open simple file SS 3.11 Link Compile Download OK. The 1701 passes signal and it appears to work fine. Right click Hardware 1701 Write Latest
-
Sigmadsp ADAU1451 S/PDIF receiver Sample rate(SR#: C14LS00381)
we want to use Sigmadsp ADAU1451 , base on the SPEC Rev.Pr0(2011) the S/PDIF receiver support 192KHz Sample rate,but SPEC Rev.C(2013~14) point out it is only support 96KHz.what happen?why they are dif