EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
1452 safeload
Hi, I use 1452 on my target board.I find something wrong with the safeload mechanism of 1452.If I use the module:Filter->Second Order->Double precision->EQ, the host can't write the parameters into 14
-
How do I multiplex 4 separate microphone channels on a ADAU1761
Hi, We are working on an application where we need to process the signal from 4 separate microphone channels by multiplexing the stereo ADC contained within the ADAU1761. I have a copy of SigmaStudio
-
1452 ASRC noise
Hi, I use 1452 on my target broad.The testing project of ASRC is attached.When I need the input from ADC ,I set the gain of ASRC to be -100dB and the gain of ADC to be 0dB. When I need the input from
-
Interfacing IR Receiver to SigmaDSP GPIO
Hello, With nothing concrete coming from AD on adding the IR library, I am opening this topic for discussion to all: How best can we interface the IR receiver (with or without a de-modulator) using th
-
ADAU1452 and ADAU1451 different setting interface in SS
Hello Support Team, I am useing ADAU1451. However, the setting interface is different between what I uesed EVB-1452 in SigmaStudio. We thought that is only different Memeory but HW is same. I would li
-
ADAU1452 CLKOUT capabilities
Dear, I plan to integrate an ADAU1452 DSP. In the data sheet is a passage about CLKOUT capabilities of the DSP. "The CLKOUT pin can drive more than one external slave IC" I would use the CLKOUT to dri
-
Few questions about the ADA1701 SigmaDSP
Hello board I was just had a few questions about the ADAU1701. I am wanting to design a loudspeaker management processor. In essence full range audio in and crossover control out so split frequency ou
-
IIR filter crashes on the fly
Hi, My set-up consists of three POTs (Q,F,Boost) connected to the ADC of a uC. The analog values are converted to an index that corresponds to Frequency, Q, or Boost level that are used to calculate t
-
ADAU1701 with I2S slave in, I2S master out?
Hi all, I have been using the ADAU1701 with a reasonable amount of success, but I just ran into a snag.. I have already managed to get the ADAU1701 to output (as I2S master) to an external DAC. Howeve
-
EVAL-ADAU1446EBZ/EVAL-ADAU1772Z Board Gerber Files
Dear Sir. We are using ADAU1446/ADAU1772 board in a design. Can you provide the gerver files for the ADAD1446EBZ and ADAU1772Z evaluation board please. thanks.
-
EVAL-ADAU1761Z to run all ANALOG AUDIO INPUTs?
Hi dear colleagues, I had just ordered and received a set of EVAL-ADAU1761Z, and plan to use all the on board analog audio inputs (IN1, IN2, and IN 3/4) as the Mic1, Mic2 and stereo audio input respec
-
problem with setting the SDATA Mode to Master
Hi forum, I am trying to make a 1761 codec to act as the master on the BCLK (I2S bit clock). I am setting it in Sigmastudio and I can see the bit 0 in register 0x4015 changing from 0 to 1. When I expo
-
PITCH TRANSPOSER
Dear support team, I want to use Pitch transposer module. But, I can't understand relationship slider and Max shift. I checked wiki, but meaning of Max shift is TBD. Pitch Transposer [Analog Devices W
-
ADAU1761 I2C burst read sequence
Hello, This is my first experience with ADAU1761. I have uploaded the firmware and registers using I2C burst write SAM D20 and I have a sound at the output, just as it is supposed to. However I would
-
Is there a Support Team???....
And if so, they are really monitoring this forum?... After a few days waiting from some help in vain and after observing the same behavior with other fellows, I am in trouble choosing one of following
-
ADAU1442 optmized filter MIPS
Hi, If the optimized filters subroutines exceed 50% of MIPS, as shown in attached figure. Can I run the ADAU1442 in 96KHz? Audio Signal Processors adau1442 SigmaDSP Audio Processors
-
1701 (DAC?) noise
I'm trying to locate the source of this noise. As soon as I put a small signal like low freq on this output, it is gone. it is only there with no input signal. I programmed a volume slider before the
-
ADAU1452 External Delay issue
Dear support team, I am trying to use the 23K245 SRAM with the ADAU1452 in self-booting mode and need your help in order to solve some issues. 1) The first issue is related to the SS_M0 (pin26). Appar
-
licensing for analog Device Virtual surround
Sigmastudio has included Analog Virtual Surround on the standard tool bar ,but on the Analog Device SigmaStudio website it states that analog virtual Surround is a licensed algorithm. What is the actu
-
Using external spdif tranceivers with ADAU1452
Hello, My questions pertains to clock connections on the ADAU1452 when using external spdif transceivers. My design requires 2 spdif inputs and outputs to be processed by the ADAU1452. I have elected
-
Question about Tolerance block and State Machine block
For my project I need to boost weak signals and to attenuate strong signals The volume from the input should be in a certain bandwidth. I made the attached scheme for testing, put the max allowed volu
-
forcing ADC_SDATA to act as a PWM
Hi forum, I am trying to force the I2S digital output (pin 26 on an ADAU1761) to output a PWM signal. In order to succeed this I am forcing the I2S output to certain DC values by using DC sources in S
-
Readback gain reduction of Dynamic Processor with ADAU1452
How is it possible to access the gain reduction of a "Dynamics Processor" with a microcontroller ? I need a readback possibility of the actual Gain value. DSP is ADAU1452/1442. Any ideas ? Bernd Audio
-
ADAU1761 i2c address issue
Hi I am using ADAU1761 and i have connected both ADDR1 and ADDR0 to GND. According to the datasheet (Table 21), the ADAU1761 12c address for writing to a register might be 0x70. and for reading might
-
ADAU1401 EQ setting (SR#: C14K100362)
Dear FAE & AE Team: We design a audio system based on ADAU1401 with 10Band EQ inside. We have design a GUI system; user can change any parameter in DSP register. When drag the thumb in sigmastudio to