EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Amplitude Modulation Question
I just started an amplitude modulator design in SigmaStudio, The 1st thing I would like to do it to setup different modulation wave forms and select the one I want to use with a switch. That signal is
-
ADAU1701 programming
Hello, i'm an Italian student working on its Master of Science thesis trying to achieve higher performances using feedback control and digital signal processing algorithms. Since my thesis is develope
-
ADAU1452 too long selfboot time...
With two FIR blocks of 8192-taps, the booting time is about 50s !! Reading the manual, it seems that it is supposed that the E2prom starts to be accessed at low speed that it is later increased (?). H
-
Sigma 300 (ADAU145x) Slew Volume Rates
Slew volume controls can filter noisy control inputs and minimize clicks. Often the desired slew rate can be found by experiment. However, in some applications it would help to know the actual slew ra
-
Convolution reverb on SigmaDSP
Hi there! Does anyone know whether it is possible to get convolution reverbs working on a SigmaDSP chip? I need to choose an impulse response from a list which should be used for the convolution in re
-
I2C address for ADAU1761
Hi Could you please tell me, what is the I2c slave addresse of ADAU1761? Is it 0x70 or 0x38? Thanks Audio Signal Processors SigmaDSP Audio Processors adau1761
-
ADAU1442 with Two ADAU1701
Hello, I am making a prototype for which my requirement is as given below: 1. SPDIF Input (1) 2. SPDIF Output (1) 3. Analog Input (at least 1 stereo channel) 4. Analog Output (at least 3 stereo channe
-
Volume controls on ADAU1701
Hi All Just a quick heads up about a problem I found controlling the SigmaDSP volume controls from the I2C port. If you capture what SigmaStudio does as it changes the volume settings, you can see it
-
EVAL-ADAU1442EBZ SPI Communications mode configuration help reqd.
After reading a couple of earlier postings about getting this board to run at 96 or 192kHz, fs I learned it is first necessary to configure SPI communications. My plan of approach is to first establis
-
Multichannel Audio Codecs for SigmaDSP
I'm using the ADAU1451 in an upcoming design and am picking out audio codecs to use alongside it. The SigmaDSP's serial audio ports theoretically support 8 or 16 channels each, but it seems like none
-
Interfacing ADAU1701 with AD1955 (2)
As a bit of a continuation from Interfacing ADAU1701 with AD1955 Has anyone successfully used an ADG3304 for I2S level translation from an ADAU1701? Or could anyone offer an educated/experienced guess
-
Questions prior to evaluating the ADAU1452
Hello, We are looking for an alternative to our current DSP solution. The ADAU1452 looks good but the development of the Sigma series seems to go faster than the documentations. Our questions are: 1.
-
Use ADAU1452 in embedded system - remote control via SigmaStudio (TCP/IP?)
Hi there, I see that SigmaStudio has TCPIPADAU1761 and one for ADAU1421, also there is TCPIP1940 interfaces available. How would they be used in a project? I am trying to acomplish the same for my ADA
-
ADAU1450 routing matrix
Hi, Are there any know issues with the routing matrix of the ADAU1450 module? The reason for this questions: Actual configuration: ADAU1450 and sigma studio 3.11.2. There are no output signals at S_DA
-
ADAU1452 GPIO
In the Evaluationboard User Guide ( UG-636) is written, that GPIO MP5 is on TP38. If I look on the schematic of UG-636 : TP38 is analog input channel ADC1LN. Is the table 4. Multipurpose pins , GPIO's
-
ADAU1446 I2S sample rate
Hi! We have a custom board with a ADAU1446 SigmaDSP and a AD1939 CODEC, both running with a master clock of 12,288MHz and sample rate of 48kHz. We would like to connect a Bluetooth board/chip over I2S
-
ADU1446 sleep mode
Hi! We have a custom board with a ADAU1446 SigmaDSP (selfboot from EEPROM), a AD1939 CODEC and a PIC microcontroller. -Is there any possibility to run the DSP in a sleep mode (less then 40mA) when aud
-
Using ADAU1452 with embedded linux system over SPI / I2C
Dear Ladies and Gentleman, we have a project where we want to use the ADAU1452 as a DSP in a power amplifier. Currently we use ADAU1442. I found the kernel module https://wiki.analog.com/resources/too
-
Adding OffChipDelay functionality into CrossCore application
Hi, I am going to add a OffChipDelay functionality into SigmaStudio schematic and CrossCore application. I have already read <Off Chip Delay (External Port)> (https://ez.analog.com/message/158406#1584
-
I2C triggers I2S issue
Hi forum, I am working on a product that carries an ADAU1761 chip and an external MCU. The two chips communicate through I2C protocol. I am witnessing some weird behaviour however: I am have set my DS
-
ADAU1772 output analog filter
Hi, I would like to know if it is a good idea to add an external Low Pass filter to the ADAU1772 at analog output? I understand that a High-pass filter is necessary to remove the DC from the output, b
-
Gain Envelope Anomalies
A question / bug report: The 'Endless Loop Generic Gain Envelope' function in Sigma Studio seems to have some 'undocumented features.' 1) One would think that a setting of 0dB in the gain envelope GUI
-
ADAU1761 at non-audio sample rate (i.e. 51200)
Assuming i used a 26.2144MHZ MCLK instead of 24.5760MHZ, is there any problems with running the ADAU1761 at 51.2 kHz instead of 48kHz? The filter coeffs would be designed at 51.2 kHz. Audio Signal Pro
-
ADAU 1442: Problems to set FS 96/192kHz
Hello it seems that SigmaDSP doesn't set the ADAU 1442 to the desired 96 or 192 kHz. If anything is set to 96 kHz, the 1442 outputs send every 24-Bit Data twice, so the real resolution stays at 48kHz.
-
PCB considerations - Sigma ADAU1452
I'm starting to play with the ADAU1452 eval board. While contemplating my end product, I'm curious about some of the requirements. My first question is, and I apologize if this is too freshman, is it