EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Evaluating dsp resource usage, and external eq control
Hi I am running SigmaSudio, with the sharc add on and cross core. Is there any way for me to evaluate my dsp resource usage without the development board? I am looking to build a very large progect an
-
basic delay using sharc internal memory
Hi I am trying to build a basic delay. Everytime I load up a normal SIgmaDSP, I can utilize the maximum delay ram, and get a good result. Every time I load up a sharc DSP, I cannot get any result. The
-
Read Audio Levels in DSP
I am using Sigma Studio with the ADAU1452 DSP. I've been trying to find a block in Sigma Studio that will allow me to read the current audio level using the SPI register interface at runtime. There is
-
ADAU1772 core_fs bits
Hi, I'm refering to ADAU1772 data sheet rev.C and SigmaStudio 3.11 to confirm the operation and noticed that if I creat project file, the core_fs bit is set as 96kHz. And I can't find a control to cha
-
ADAU1772 Noise with parametric EQ + dB Volume slider
Hi I tested below signal flow with ADAU1772 but somehow pink noise like sound outputs from ear-phone. If I remove "dB Volume Slider" and recompile it, noise is also disappear. Is there a limitation of
-
Crash when trying to change filter type
I try to click on the filter type button for the last filter on the right, and SigmaStudio 3.11 64-bit crashes: --------------------------- Application Exception --------------------------- InvalidArg
-
ADAU1701 GPIO as 4 Input Mux Switch
Hello everybody, I need to cost down by eliminating the uC in my system and one of the functions, I believe I can transfer to the DSP is the mux switch. Can someone help me realize this switch Mux imp
-
Slave to TDM Clock Domain
I want to bring in a TDM8 clock domain (BCLK and LRCLK) to domain 2 (for example) on the ADAU1442 Sigma DSP. I then want to set the Start Pulse Select value to "fs from serial input pair 2" so that th
-
Program Load
Hi Guys, I have just gone to program some boards today with the latest version of sigma studio and its different to the older versions. In the old version you would write to eprom from the config scre
-
How to calculate the coefficient of "bass boost" module in ADAU1701?
Hi everyone, I'm using ADAU1701 and would like to control it with the MCU as the host.As I am going to use "bass boost" in my schematic,but I can not figure out the formula to calculate all the parame
-
ADAU144X Read Program Data with I2C
Hello, I'm using a ADAU1446 DSP. I can program it using I2C and a PIC32 mcu, it works correctly. When I'm trying to read back the data, it fails for the program data. I can read all registers from the
-
ADAU1452 Throughput Delay
Greetings, I'm hoping to find some information on the expected delay from an I2S Input to output of the ADAU1452 Sigma DSP configured for: MCLK = 24.576MHz, PLL divider settings to produce a 294.912MH
-
Clocks for ADAU1701 and Codec CS4272
Hi, when the ADAU1701 is confugured as a master, getting its MCLK=12MHz from OSCO and MCLKI there are 2 possibilities in the datasheet to get the clocks to the codec CS4272. First is to use an additio
-
cascading 2 1445 dsps
Hello, My application requires daisy-chaining two ADA1445 dsps. I'm using 4 ADAU1974 ADCs for input, and a single ADAU1966 DAC for output. I am connecting the serial data outs from the ADCs straight i
-
ADAU1761 design: Signal Detection Cell is used to monitor the incoming audio signal
Dear sir, In my customer's ADAU1761 design, they would like to use Signal detection cell to monitor the incoming audio signal. Once no audio signal is present at the input for a given amount of time,
-
Exactly what i2c boot content is required for the ADAU1761?
The data sheet for the ADAU1761, page 45, paragraph STARTUP states: The following steps should be performed every time a new program is loaded... Set the DSPEN bit in R61 Set DSPSR to 1111 in R57 Set
-
ADAU1701 Leaky Mute.
Hello, I wish to use a GPIO controlled mute switch and have used the 'single slew ext volume' block to do so. This sort of works but allows a distorted (attenuated but audible) signal through when mut
-
controlling program flow
Hi, I understand the way a SigmaDSP chip works, doing all it's program within a frame of the audio sampling frequency. My question is whether there is a way to control the order in which instructions
-
Signal Detect alg. trigger time value format
Hi does anyone know what format the TRIGGER TIME is in for the SS LevelDetectors/Signal Detection block ie the one below https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/leveldetec
-
Creating a simple I2S path through an ADUA144X eval board
I'm really in need of some help here. I'm using the Sigma Studio s/w to create a simple digital audio path through the ADUA144X eval board. I need to generate a tone (on my board I have a 440Hz tone)
-
Pot on ADC to select index filter
I had this working swell with a pushbutton on a counter. Now I want a turn a pot and select different filters, sort of like "presets". Clearly I am doing something wrong. What is it? The GPIOs are to
-
Frequency dependant gain stages
Hi, We have a question with regards to the ADAU1701 and Sigma studio that we hope you can help with. We are trying to simulate a constant current output from a voltage amplifier (power amp) when drivi
-
Changing filters in real-time using I2C or SPI
Hi, We have the ADAU1452 eval board. We use Sigmastudio to build and upload some filters and store these in the EEPROM. It was very simple to get this working. But… We want to dynamically adjust filte
-
About external delay (SPI RAM Delay) in ADAU1452
hi, About "external delay" in ADAU1452,how to use the module(SPI RAM delay )? How about Setting the Master Control port Properties? Best Regards, yang. Audio Signal Processors adau1452 SigmaDSP Audio
-
Output range of Sawtooth at ADAU145x
Dear support team, Could you tell me output range of Sawtooth module,please? I think that output range of Sine tone module is -1~1. But, range of Sawtooth module may be 0~1. And could you write the in