EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
adau1452miniz board, AD1938 codecs 192khz possibility question
Hi guyz! Many thanks to AD people, now I have 1452miniz board and can continue development of the assistive device for the blind. Now I am reading the board's datasheet and meet the following passage:
-
First impressions and dynamic topologies for the ADAU1452
Hello, I just get the evaluation board I bought as soon as I discovered the ADAU1452 that seems to be what I've searching for. I tried to find a kind of "number crushing" DSP with audio input/outputs
-
Is it necessary to load the contents of DATA RAM while initializing ADAU1761?
In our current design, an MCU is there to initialize ADAU1761 through I2C, with all the necessary register contents. We found the following 2 questions: 1/ In the current DSP initialization table, a D
-
Too much THD with MIXER on ADAU1701
Hi Everybody! My design is for a subwoofer system consisting of a mixer stage mixing the stereo input feeding an equalizer, with LPF further down feeding the compressor/limiter. When tested using AP e
-
16KHz sample rate ADAU144x
I have a question How do I set up the ADAU1442 so that it generates a 16KHz sample rate Audio Signal Processors adau1442 SigmaDSP Audio Processors
-
Auto-select the mux input with signal (help)?
There maybe something on this already in this forum, if so I apologies for the repeat but I couldn't find it. My application is this: I have two stereo analog inputs that run into an indexed multiplex
-
ADAU1445 ASRC help needed
Dear All, Please guide me in configuring parameter in sigma studio for routing "SDATA_IN5" thro' ASRC for ADAU1445 based project. Regards Ankur
-
Ad1940 can use c language to compile in sigmastudio
Hello: I am running sigmastudio between AD1940 evaluation board.I want to ask about that, sigmastudio you can compile our own written by c language, as well as how to compile, can you send me a copy o
-
ADAU1701 WP pin always high?
Hi, On a project I'm doing with the ADAU1701, I'm implementing a touch-controlled volume push button with the GPIO's pins of the chip. The design will not save the volume that was setted when powering
-
About the unused pin of ADAU1761
Hi all, When the following pins are not used, please let me know a setup which you recommend. 1) JACKDET/MICIN 2) DAC_SDATA/GPIO0, ADC_SDATA/GPIO1, BCLK/GPIO2, LRCLK/GPIO3 We are using it with the ini
-
ADAU1442 XLR AES/EBU Transmitter and Receiver
Hello, I want to use ADAU1442 to finish XLR AES/EBU Transmitter and Receiver. But I not found any about XLR informance. Could I use the ADAU144X to finish this function ? Thank you. --Paul Audio Signa
-
GPIO problem w/ ADAU1761
I'm trying to do something that I thought would be simple. I've been using SigmaStudio and the ADAU1761 for several years and I thought I understood how everything works; it looks like I'm coming up s
-
No audio when using ADAU1701 with I2S in from ADC
I am using an ADAU1701 as master and have a Wolfson WM8786 ADC in I2S mode (have also set the DSP to that of course). I can see that the ADC is generating bits and the DSP is generating the word clock
-
Stand alone audio processor with 16x2 LCD ?
Hi, I've seen ADAU1452 can be SPI and I2C master, it can drive GPIOs and do self boot from EEPROM, besides it has lots of memory and can implement State Machines with SigmaStudio 3.10.4. I'd like to u
-
ADAU1442 - Can I output two TDM16 streams?
I'm processing 16 stereo channels. Can I output those as two TDM16 streams using the ADAU1442? I think the answer is no, because there aren't enough output channels. I also want to verify I can input
-
ADAU1966 comparable ADC
Does anyone know if ADI has plans for an 8-channel or 16-channel audio ADC with a TDM output anytime soon? The ADAU1966 looks awesome. I would love to have a sister device to use on an analog front en
-
ADAU1452 register setting for 96kHz fs DSP Core operation
Hi There is thread that explain 96kHz serial port operation for the ADAU1452. https://ez.analog.com/message/139867#139867 But I'd like to make sure the register setting include core. If my MCLKI is 24
-
ADAU1761 I2S slave mode with non-synchronous MCLK
Hello All I have a quick question about the use of the ADAU1761 I2S port in slave mode. I have tried the following experiment using an ADAU1761 and ADAU1701 evaluation kits. I created a simple project
-
ADAU1701, setting the Serial port left-justified, the output data is rarely incorrect
Please let me ask you about ADAU1701. If you know any solutions or information, would you please let me know ? When setting the Serial data output left-justified, there is a case that the only 1st bit
-
Problems with DC Blocker for ADAU1452 in SigmaStudio 3.10.4
Hi there, obviously there's a problem with the DC Blocking Filter for the ADAU1452 in the latest revision 3.10.4. If I only use one single DC Blocking filter for one channel in a project, everything's
-
How to generate MISO output signal from ADAU1701 for SPI control mode?
good day everyone, I am using ADAU1701 and arduino for SPI control mode. My question is, How can I generate output signal from MISO (COUT) pin of ADAU1701 using sigmastudio? ADAU1701 is in SPI control
-
"Add" Features Does Not Simulate in Sigma Studio
Hi Everyone, I'm using the Stimulus and Probe blocks in simulating the behavior of the ADAU1772. All works fine until I try and split part of the signal with the T Connection 1772 and then after some
-
ADAU17xx power down
In SigmaStudio there is an option to power down the ADC and DAC part of the ADAU1701 Does that actually mean that they are completely shut off so they don't draw any current? If not, is there another
-
Self-Boot ADAU 1442
Hello! If I flash the DSP using the Programmer it directly works fine. Flashing the EEPROM gives no error and using the "read EEPROM to Display" shows also that there is something written in it and it
-
Sigmastudio projects and intellectual property
Hello, I'm currently working on Sigmastudio project for audio signal processing for a product. This signal processing, will be later transmitted to an third party factory who will work out the hardwar