EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Multi-Rate Project on ADAU1452
Hi there, Is there any way to set up a multi-rate project in Sigma Studio using the new ADAU1452? Thanks for any help getting started. Kind regards, Chris Audio Signal Processors adau1452 multi-rate s
-
How to determine which frequency band has highest magnitude
Hi all. I'm using ADAU1701 and SigmaStudio 3.10 beta. I want to design a Index Selectable Filter to cut off the audio feedback from different sources, eg: microphone, hoots and howls, Different source
-
Is it impossible to set Fs=192kHz for EVAL-ADAU1452MINIZ?
In EVAL-ADAU1452MINIZ User Guide UG-636, I found the line below. " The AD1938 is configured to run at a sample rate of 44.1 kHz or 48 kHz. It is not possible to change this setting. Even though the AD
-
AES EBU & SPDIF
Hello, i was just curious if i can just use the spdif I/Os of an ADAU1446 for direct connection to and from AES/EBU equipment. For what i've understood, the two formats are quite similiar, with the ex
-
SigmaStudio Bugs
SigmaStudio Version 3.9 Build 2. Rev 1246 7/24/2013 Computers used both 64 & 32 bit Windows 7 Sometimes when Im working with SigmaStudio, the software bugs out and I loose the ability to open graphs o
-
What is the rise time of bclk output in ADAU1442?
I would like to know what the rise and fall times are for the BCLK outputs on the ADAU1442 so I can determine the length of traces I can use and whether or not to buffer them Thanks Gerry Audio Signal
-
CRC on 1446
Hello, i've read that were some issues with the CRC generator on ADAU1442/6, https://ez.analog.com/message/10660#10660 I've read also the solution proposed by Brett, which consists in clearing the rem
-
Allowable Sample rates for the ADAU1701
Hello All The ADAU1701 has a maximum sample rate of 192kHz. However the datasheet does not specify a minimum sampling rate (that I can see anyway). If I use a lower crystal input frequency or select a
-
IIR cascade FIR, incorrect phase response display
Hello. I'm using chip ADAU 1701, fs=48000. Sorry, I am a newbie in filter designing. I would like to design an IIR Notch filter at 1kHz. I used "ScopeIIR" software to get the IIR coefficients. Then, I
-
IIR cascade FIR, incorrect phase response display
Hello. I'm using chip ADAU 1701, fs=48000. Sorry, I am a newbie in filter designing. I would like to design an IIR Notch filter at 1kHz. I used "ScopeIIR" software to get the IIR coefficients. Then, I
-
Stable SPDIF I/O at 44.1kHz on EVAL-ADAU1452MINIZ EVM?
I am measuring the SPDIF I/O performance of the ADAU1452MINIZ EVM. My measurement system can record the exact output (with delay) when using SPDIF loopback at 44.1 and 48kHz. I set up the EVM (with Si
-
idle tones at 6k and 12k with ADAU1701 and firewire soundcard combi
Hello, I'm measuring 6k and 12k idle tones on all audio outputs only when my ADAU1701 board gets it's clocks from an OEM Firewire soundcard. As long as I use the on board clocks, audio is clean. The h
-
ADAU 1701 control with Arduino MCU and Keypad
Hello, I hope can get help here...I want control Class D amplifier with ADAU 1701 DSP controlled by Arduino MCU with Keypad look picture. in Webstores I can buy different ADAU1701 development boards.
-
Using WM8805 with ADAV4601
Hello, WM8805 is an SPDIF transceiver from Wolfson. I want to use it in hardware (HW) mode with ADAV4601. In HW mode, the datasheet of WM8805 mandates use of an external crystal/ clock of 12MHz only.
-
ADAU1761 serial port doesn't work.
I'm implementing simple design based on ADAU1761. The source for ADAU is ASRC. MCLK is 24.576MHz for ASRC and for ADAU. Output serial port of ASRC also clocked from MCLK, i.e. it is synchronous with A
-
Using ADI Plug-In Algorithms in Sigma Studio
Hi, I'm interested in evaluating the ADI SuperBass Plug-In Algorithm for SigmaStudio. How do I get setup to do that? I'm using the ADAU1701 SigmaDSP and possibly will be using the new SigmaStudio for
-
ADAU1701, does the RESET input have hysteresis ?
Hello, After reset and boot sequence, the ADAU1701 processor sometimes does not work normally, I found. If the RESET ramp rate is slow, could it cause problem? ADAU1701, does the RESET input have hyst
-
High pass filter issue for sigma3.9 version.
Hello , I am use Sigma Studio to setting sigmaDSP , but I have some question. High-pass first-order differences between the different versions in SIGMA Studio, Calculated according to the formula desc
-
Read EEPROM from EvalBoard 1701!...
Hi Guys, I lost my set up on SigmaStudio, and I want to read my setup thru Evaluation Board by SigmaStudio. Is it possible? Thank You eeprom adau_1701 evaluation_board
-
Algorithm to suppress self-excitation?
Dear Sir You know there exists self-excitation in Microphone-Speaker-Microphone application. I add a 5-band EQ, the center fre are 50, 150, 400, 1K, 5K. I try to lower down some center fre to suppress
-
block addressing
I'm referring to this post https://ez.analog.com/message/32330#32330 about "grown" blocks addressing and i'm facing the same problem. In detail, i would have the addresses of a grown simple block, in
-
ADAU1446 Hilbert transform response
Hello, i'm using the Hilbert transform block on an ADAU1446 for envelope calculation. It really has a phase difference of 90° between its outputs, but you cannot call any of the two output a "zero deg
-
how can i use the algorithm of pitch transposer
hello 1. I plan to use the new IC of ADAU ADAU1452 ,but i can't find the algorithm of pitch transposer, if i want to the algorithm, how can i do? 2. If i want to use the algorithm of Parametric EQ wit
-
Sigma Studio installation problems with Windows 8
Hello I am trying to install Sigma Studio onto a Windows 8 machine and whilst running through the "copying files" part of the installation I get the error message:- Error 1320. The specified path is t
-
Are there logic operators available for the GPIO inputs of the ADAU1445?
Hi, We use the ADAU1445 audio processor for intercom - and audio purposes in a video camera system. At startup of the system we load the processor software via the I2C connection. For test purposes in