EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1452 Volume control via Auxiliary ADC input does not work
I want to implement a volume control in a ADAU1452-project which shall be controlled by an Auxiliary ADC input. In combination with a SIGMA100 and SIGMA200 DSO this is very easy, as I simply have to c
-
How to operate regarding "Real Time Display".
Hello, Could you please let me know regarding "Real Time Display" of the Basic DSP library of the toolbox. I'd like to check a waveform on graph in the Real Time Display out in detail. Can we set more
-
Help file for Algorithm Designer
Sorry if I missed it if it is already posted somewhere. kk
-
Question regarding ADAU1446 DSP signal detector
Hi.... I'm using ADAU1446 audio DSP. Regarding signal detector block in the DSP, when we inject audio signal and read the detected value from the detector, we can get a 6digit hexa number like "0x5547
-
Can ADAU1701 support TDM and I2S mixed up input?
Hi Brett I read the datasheet and tried in the SS, I think the anwser is NO. But I want to confirm it --- Can ADAU1701 support TDM and I2S mixed up input? Thanks. BR, Jackie Audio Signal Processors Si
-
ASRC output rate setting for the ADAU145x ADAU145x
Hi, According to the data sheet for both ADAU145x, ADAU144x, there are register to set ASRC output rate and are selection like "DSP RATE" or "DSP Core Audio Sampling Rate" "Internal FS" What is the di
-
About interface read module for ADAU1452
Dear support team, I want to know some value of internal node of signal flow by interface write module. Because , the module is very useful for debugging at ADAU1401. But I can't found registers in AD
-
Filter with external level, center frequency, and Q controls (GPIO)
I am looking to create a filter (General 2nd Order for now) where I can edit the level, center frequency, and Q of the filter using external controls. So far, I have found ways to adjust either the le
-
Is there a cross table "algorithm x device" ?
Hi, I'm using SigmaStudio 3.9 in Win8. When I use a ADAU1701, I don't find the "flanger" or "Reverb" algorithms in the toolbox. Is this right? Is there a cross table "algorithm x device"? Thanks, Audi
-
fail to generate the "spi_params.dat" file
Hi, After compiling the project in the sigmastudio, I find that something is strange.I can't find the "spi_params.dat" file which must be generated according to the comlier_output file.What's more,the
-
Summing up knowledge base of Sigma DSP system
Hello, I'm an Elektor reader, and I'm here just to sum up and I hope to discuss with you my basic knowledge of the Sigma DSP system/enviroment. So you have this great Sigma Studio SW, wich lets you de
-
Project Update
Hi Guys, I just thought i would post an update on my project, this is the board assembled. Its been a steep learning curve but its all good. The board was hand built by me and reflowed on my own equip
-
Can I design a variable frequency filter for a Wah Wah effect?
Hey guys. I am trying to design a Wah Wah effect for guitar using the 1701 evaluation board. The textbook I'm using shows a signal flow graph that has a time varying band pass filter with variable cen
-
about ADAU144x DIN5(Pin91)
Dear support team I'm using 1446 and 1442, their DIN5 (PI91)with any signal input, an error occurs. The performance of the hardware is not working properly, the level meter indicator bounce. However,
-
About CLKIN wave form for ADAU1442 and ADAU1452
Dear support team, We want to know specification of CLKIN for ADAU1442 and ADAU1452. We will use 12.288MHz clock source for CLKIN.(not crystal) Q1: Is Input level of CLKIN same as digital input specif
-
ADAU 1701 CM pin, 47 or 10uf?
Hi, This question is about the CM pin (40) in the ADAU1701. Reading the datasheet (Page 13), on the CM pin description, they say you have to connect a 47uF decopuling cap: "1.5 V Common-Mode Reference
-
binary control
hello, I need to control 6 multiplexers by a single byte, where each bit in a control byte controls its own multiplexer. How can I accomplish that ? Thank you, Gennady
-
EVAL_ADAU1701MINIBZ with NO power supply?
Hi, I'm writting here to announce that I have just recived an EVAL_ADAU1701MINIBZ evaluation board, which in theory comes with the USBi board, the ADAU1701 board, the USB cables and a POWER SUPPLY. "T
-
Level meter not showing correct levels.
Hi, In Sigma Studio, a schematic which has an audio input,a mute block, Compressor, EQ, then a level meter. When audio plays the level meter works correctly, but when I mute the signal it still shows
-
Analog/Digital(I2S) selectro for ADAU 1702
Hi, I have a design where I use ADAU1702. I have two audio input sources to my system that I want to be able to select between: Source (1): I2S stereo digital channel from a Bluetooth module Source (2
-
Hardware Sample Rate vs Software Sample Rate
I am confused and am looking for more explanation about the difference between the hardware and software sample rates. Do they have to match? Can your hardware rate be higher than your software rate?
-
SigmaStudio Compressor Issue
Hello I am test compressor function of the ADAU1761 that have discovered an issue. If setting RMSTC 10 ms and Decay 10 ms , then 20 Hz signal will some distortion as follow as the IMG_0517. If setting
-
ADAU1701 I2S In - Stereo Out
Hi There, My project consists of ADAU1701 as a slave feeding I2S signal from another IC (HDMI converter - EP94Z3E). The 1701 receives the I2S and outputs it as an analog stereo. Digital IN, Analog OUT
-
Matlab Filter Design vs Stimulus/Probe show different results
Here is my MATLAB filter design: SOS and G matrix output: SigmaStudio Code: And finally Stimulus/Probe output: What am I missing here? The magnitude is waaaaay off and the peak frequency is also shift
-
Complement to Zero Comparator for input?
The zero comparator (and buffer gate) can write directly to specified bits on the output, but is there a block that can read directly from specified bits on the input? Other than doing a whole lot of