EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 accuracy of DAC full-scale-analog-output
Hello there, The ADAU1701's datasheet tells me, that the full scale analog DAC output is 0,9 VRMS, but I measure 1 VRMS. (The DAC output feeds an active filter in my application.) This results in an a
-
Automatic fader; any ideas?
Hi, Anybody a idea of how to design an automatic fader? The fader should be triggered if signal (speech) is present on an input and the fader should ramp up from -3dB to 0dB in a period of 2 to 3 seco
-
Can obtain the angle information of moving source in the stereo field using four microphones and the module of adaptive beam forming in SigmaDSP?
As discussed in “SigmaDSP Two Microphone Beamformer(https://ez.analog.com/message/43552#43552)”, a new algorithm has been created for the ADAU1761 that will take two microphones and adaptively beamfor
-
Audio DSP
Hello! I am new there is this forum. My name is juergen and I live in Aschaffenburg / Germany. I post in this forum, because the AD DSP support has not enough time to handle my formal support request
-
Optimal ADC input resistor for ADAU1701
Hi There, Considering I have an input buffer that I can change the gain, what would be an optimal input resistor value for the ADAU1701 for less possible hiss? Currently the buffer is unity gain and t
-
How to use Analog.SigmaStudioServer.dll in visualC++
Hi all, I would like to use Analog.SigmaStudioServer.dll in visualC++, does anyone have some example code or document on how to use Analog.SigmaStudioServer.dll in VC++ project and run the sigmastudio
-
Sigmastudio 3.9 treetoolbox without adau1452
hi : Why no found adau1452 form the processors(IC2/DSPS) list of tree toolbox in Sigmastudio 3.9. best regards alber Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
DSP Newbie needs starter kit
I have an application for ultrasonic echo location robotics sensor which has 4 microphone inputs (preferably analog so I can make sense of the inputs) The received U/S signals are 25khz, and need enou
-
Sigma DSP muxes or volume sliders in schematic page won't changes states
I have an issue with SigmaDSP where I can't get some of the muxes or volume sliders to change states on the Schematic page when testing my design. Has anyone seen this issue before? Some of the slider
-
A question about the power of ADAU1761
Dear Sir We concern the power of ADAU176. As discussed in the datasheet, the ADAU1761 is a low power processor that supports stereo 48 kHz record and playback at 14 mW from a 1.8 V analog supply. Howe
-
How ADAU1452 use DM0 RAM memory?
I use adau1452 and sigmastudio tool to development . I find adau1452 have 2 section ram. DM0 and DM1, And I use delay,but it's only consume DM1, not DM0, So I want use "delay" function or others consu
-
ADAU1701 TDM input slave mode
Hello, I'm coupling two dsp boards. Both equipped with one ADAU1701. The master board is clocking out TDM in master mode, the slave board's DSP should clock-in the TDM data in slave mode. I know for s
-
How to calculate the Factional Delay sending data ?
Hi guys, the sample delay cell, i know how to caclulate, but it have click noise when sending data. so i need to use this Factional Delay. this "Factional Delay" cell, the step is 0.01 0 --> 100% send
-
Sine Frequency division/multiplication??
Hello everyone! Perhaps not a very smart question, but I just wanted to ask, whether sine frequency division/multiplication can be implemented somehow in sigmastudio? Just is it theoretically possible
-
My first Board ever!!
Hi everybody, it is kinda silly, but I just wanted to boast a bit and say that I designed, made and manually assembled the first board in my life! Soldering joints look ugly, but it works!! The size i
-
Problem about Initialization
I use mcu (stm32f107vc) communicate with adau1442 via i2c.the mcu can read date from eeprom,but it can't read from adau1442(There is no response when I send 0x70 to adau1442).if there is something wro
-
Getting natural speech with a 1:2 Decompressor
I'm having a lot of difficulty getting natural sounding speech using a compressor box (peak, RMS, or combo). Attacks are too loud compared to the rest of the clip, but as I tweak the knobs, I can't le
-
Sigma Studio and EEPROM Programming
Hi Guys, I need your help again please. I had problems getting the ADAU1701 working in selfboot mode, and the problem was solved here: https://ez.analog.com/message/115973 When replicating my PCB with
-
TDM between AD1401 and AD1940 eval boards revisited
Hello, Sorry I had marked my previous post http://ez.analog.com/message/117014#117014 as assumed answered by mistake, but I would appreciate help with this. I've been able to send I2S stereo audio fro
-
Noise Gate not Functioning Properly
I have an application where I'm using an RMS (no Gain) Compressor (several of them) to create a noise gate, but it doesn't appear to work. I have an external POT controlling which noise gate path to s
-
adau1452 pcb layer
hi : Auau1452 demo board for four layer with PCB. Now i want to doing two layer ? can it? need to noto those ? best regards alber. Audio Signal Processors adau1452 SigmaDSP Audio Processors
-
ADAU1772 decimation response
I am using the ADAU1772 as a low-power quad ADC (DSP disabled) and it is working perfectly. However, the ideal passband for this application is very similar to the "Total Decimation Response" graph sh
-
ADAU1701 I2C boot
Hi, I'm trying to boot an AUDA1701 from an I2C EEPROM, but unfortunately the I2C communication stops after a few byte transmitted. In general, the I2S communication seems to work. I can also read the
-
ADAU1701 - how to change dynamic processing via I2C
Hi, I have a customer who needs to change the dynamic processing on the fly ( like time contant ). They want to do this via I2C. How do you accomplish this? They are using the ADAU1701 Sigma DSP and S
-
ADAU1452 pass transistor power dessipation
Hi Support Team, I am assuming the DVDD current for ADAU1452 is to be maximum 40mA. Now when I need to calculate the power dissipation in the external pass transistor, I simply do (3.3 - 1.2) * 40mA.