EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
NxM Mixer Export Bug in SigmaStudio 3.9 on ADAU1446
When we create an NxM Mixer in SigmaStudio 3.9 and download that file into the ADAU1446, it compiles quickly, downloads properly, and works as advertised. However, when you then go to export system fi
-
1701 built-in resonator vs external one
Hi people, just a follow-up question, as far as I could understand from the data sheet, the 1701 has a built in resonator, so the question is, why in people in general and 1701miniz board in particula
-
Help with OSCO pin please!! adau1701
Hello everybody! I have just soldered my first adau1701 board. The thing is I haven't soldered the i2c yet, so cannot program the chip to test it. The thing is, I measure the resistance between the MC
-
ADAU1701 programming
Hi, I'm working on a project that should allow people to build basic DSP functionality without the need of low-level programming a DSP chip. I like Sigma Studio, because it does exactly this. Unfortun
-
EEPROM selection for 192KHz fs ADAU1701
Hello, I'm searching an EEPROM for self-boot the ADAU1701 working with a sampling frequency of 192KHz. The datasheet specifies that the ADAU1701 generates SCL at 8 x fs, so for a 192KHz samplig freq,
-
Where is the Parametric EQ ?
Hello every body, I am new to SigmaStudio and Analog device DSP product, and I live in France. I have just download the Sigma Studio 3.9 and started a project for ADAU1442 and I can't find the Paramet
-
ADAU1702 simultaneous signal path question
In our application, we need to simultaneously do the following with the ADAU1702: Analog signal IN to ADC0 and ADC1, convert to digital Route that digital signal OUT to another micro for additional pr
-
external ADC/DAC setup with ADAU1701
Hi guys, I hope you could help me... I'm developing a dsp board with the adau1701 dsp and external ADC (PCM1804) and 2x DAC (PCM1798), so 1input ch/4output ch setup. I have read in the datasheet of th
-
Serial Output Control register settings (2078) adua1701
Hi all, I need some help understanding the settings possible for the serial output control register setup of the adua1701 in combination with an external adc/dac. The design is based on a 48kHz sample
-
wires in adau1701miniz programmer
Hello everybody! Since I have been making my own adau1701 board and since only 4 wires are necessary for programming, I decided to use a 4-wire connector and thus, makeover the standard programmer, wh
-
HILBERT TRANSFORM on 1701
Good morning to everybody I use the version 10 BETA of Sigma Studio, in the attached figures the result is seen. Doesn't something work it is a bug of the releases? Other problem, writing this simple
-
safe load cause noise in SS3.9?
Hi all, Tools: the latest SigmaStudio v3.9 When we access the safe load register on the ADAU1702 it happens frequently that the DSP afterwards makes a lot of noises. When we use the same software in a
-
ADAU1761 Latency
Hello Could you tell me how many is the ADAU1761 DSP full loading's latency, please ? Thank you. Audio Signal Processors SigmaDSP Audio Processors adau1761
-
The De-Emphasis filter function issue
Hello I am test De-Emphasis filter function at ADAU1761. I discovered that it can work at 48KHz sample rate , but can not work at 96KHz sample rate. How can I setting , if I need use De-Emphasis filte
-
ADAU1761 Hardware Application
Hello Could I use a ADAU1761's one channel ADC to measure DC voltage ? Thank you. Audio Signal Processors SigmaDSP Audio Processors adau1761
-
Any updates on the development of IR receiver module for SigmaDSP?
This module will integrate a lot of functionality and will reduce development time. Is there any update if the SigmaDSP software team is going to look into this soon? Thanks in advance! Regards, Ravin
-
SigmaStudio MatLab COM Server REGISTER_WRITE syntax
Hello, I am new to DSP programming, and I have the numbers that I want to write to the registers, and the addresses, but I am planning to use matlab to safeload a parameter value into the parameter ra
-
Resources used by Sigma divide-by block
I'm re-posting this question because it seems to have dropped out of the general discussion area. I did receive an early reply from another user, but need further clarification, especially if this ind
-
ADAU1446 and AD1938/9 clock and programming
Hallo, I bought the ADAU1446 Evaluation board and it works fine (except some trouble with noise/rustle/crackle - it will be another tread and i will do some tests...) . Now, I'm drawing my own schemat
-
A Question encountered in IIR filter design
Experiment:We design an IIR filter in Matlab,then the filter is transplanted to Sigmastudio,However the Magnitude Responses obtained by Matlab and Sigmastudio are different。Why? The Detailed operation
-
Question: Resources used by Sigma divide-by block
(Using Sigma 3.8) I have a design that uses six divide-by blocks, all in near-identical applications. When I check the resources used in the Output window, I see that three of them have twice the MIPS
-
VOLTAGE CONTROLLED OSCILLATOR RESET PHASE
Good morning, I have some problems when I use, Voltage Controlled Oscillator Reset Phase In the attached images the problem is evident. I would also like to know where I find the description of the VC
-
Active Filter Supply
Hi, in the datasheet of the adau1701 is an example with the active filter. is this opamp supplyd with + and - or a single one? thanks for the help. hubijo Audio Signal Processors SigmaDSP Audio Proces
-
I2C to SPI mode change
Hi, I'm wondering what timing is allowed to bring the ADAU1701 from I2C to SPI mode? The datasheet requires to put the CLATCH low 3 times but I found no timing parameters for low and high periods. I'm
-
Eval board design files
Hi, I need to make a tiny 1701 daughter board with DIP pins, with only the most basic components. Effectively the new board will be a highly striped down version of the existing mini eval board. Is it