EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
"Voice Stress Analyzer" for SigmaDSP
It's in quotes because no claims are made for accuracy, merchantability, or fitness for a particular purpose. Rather, this is a fun gadget with which to impress your friends and kill time. As the theo
-
wrong running average parameter calculation
Hello, How can I calculate the dsp data values for running average. The help file say following for : 1-RMSTC / (10*Fs) Comparing the calculated value for Fs = 48000 RMSTC = 5000 the result is 0.98958
-
ADAU1772 for Noise Cancellation
Hello, I'm currently using the ADAU1772 evaluation board and I'm able to create a basic noise cancellation headset using SigmaStudio. I'm new to this part and DSPs in general and I'm wondering that an
-
ADAU144x/1701 GPIO Inputs 5V tolerant?
I'm working on some simple level controls in both ADAU1701 and ADAU1446 systems. I am going to configure them as up/down push-button controls, but instead of push-buttons I want to send basic 1/0 cont
-
Interfacing ADAU1761 x2
Hello, I've been working with a pair of 1761 eval boards and have run into a mysterious clock sync problem. Every ~4 seconds I have a short amplitude reduction in the output signal. I'm hearing this a
-
SigmaStudio under Win 7 X64
Hi, Running SS 3.8 under Win XP with USBi drivers, it all works as expected. On my laptop, running Win 7 X64, with the x64 CyUSB driver installed from the AnalogDevices directory, it doesnt. When I pl
-
using the adau1701 in a product (MCU interface help)
I've downloaded the MCU integration guide and tried following it, however I hit a wall rather quickly... I tried looking for additional info on the website but could not find any. I'm not a profession
-
How to configure the input circuit?
Well here I am feeling like an utter fool but I really need to get this working. I get heavy distortion when I use my ADAU1701 and I'd dare say that the reason for this is that the input circuits para
-
384 khz ADCs?
Hello again everybody, just wanted to say that the first prototype for my assisting device for the blind, which uses scaled-down ultrasound is complete. Great many thanks to all of you who supported m
-
Real Time Display on SigmaStudio 3.8 crashes
Everytime I place the "real time display" , and click on it to see the signal , it hangs up after a couple of seconds and downloading isnt possible anymore to the EvalBoard 1701 and I have to reset th
-
Want to display graphic EQ
Hi Brett This question is just a try. There is a LCD in my product. I want to display graphic EQ while playing music. Does ADI have a solution to do audible frequency FFT and output every frequancy da
-
Digital pre-amp using SigmaDSP
Hi, I am planning to design a digital pre-amp using SigmaDSP, this project is still under concept study. The design spec for input and output would be as following:: Input - 1 Stereo audio input - 1 M
-
DSP Control Mode of ALC for ADAU1761
Hi, Currently, I'm confirming how to use DSP Control Mode of ALC for ADAU1761. I guess AIGC Output is used for DSP Control Mode. However, I can not find good document about it. Are there good document
-
ADAU1701 connect to ADMP441
Hi I connect ADMP441(digital MEMS microphone) to ADAU1701. The sound volume is not high enough. So I add 2 linear gain in serial to boost the volume. The first gain is 15, the second is 6. Then I get
-
How is hold implemented in peak compressors?
Using the peak compressor, if I turn off the decay time (instant change to unity gain), and then choose specific values of hold in ms, I get big glitches in the output. If I choose other values, I don
-
no communication from host pc and 21489 board on sigma studio
Hi I just received the ADSP-21489 EZKITLITE and am starting to work on it. When I connect the USBi block to the ADSP-214xx block in hardware configuration, the USB color is always red and it should be
-
Why does the limiter stop at +6 dB?
Using compressors to avoid output clipping says "I would suggest using a full-range (-90 dB to +24 dB) RMS compressor", but the compressors don't go to +24 dB, they only go to +6 dB: Used this way, it
-
Automatic output switch off?
Hello again peoplez! I have faced such a delicate question: the thing is I have a two sine signal sources, which I mix to a single output, I would like to have an ability to regulate the level of each
-
MATLAB FIR filter coefficients to Sigmastudio
Hello. I am more or less completely new to the DAU1701 evaluation board so please be patient with me for asking this potentially silly question, but searching this site didn't give me any result. Well
-
ADAU1701 Noob
Hi Guys, I am new to the ADAU1701 platform and trying to build a DSP module, my experience is all passive filter design (17 years of High-End audio) so this micro electronics is all new. Looking at th
-
Can I use PDM mikes with the 1701 eval kit ?
Hi All, my second post. Thanks for the response on my previous query (1781 and PDM mikes) I have another eval kit for the 1701 Sigma DSP. I'd like to connect 2 digital mikes. The docs all seem to poin
-
Clock distribution from ADAU1701 to external ADC/DAC
Hello, I would like to run the ADAU1701 with external ADC's and DAC's, maximum is 4 ADC and 4 DAC. I know for best audio result the clock has to be synchronized to all ADC and DAC . What is the best w
-
Integrating both self-boot mode and uC control?
I currently have a system running in self-boot mode with ADAU1446 with a number of GPIO ADCs controlled by external switches and pots. I would like to control a few of these SigmaStudio parameters wit
-
Re: ADAU1701 I2S Input
I have exactly the same problem. Maybe I should also improve the signal quality, but why is the analog audio cutting out as soon as I connect LRCLK? It seems that the ADAU1701 is shutting down, but wh
-
SigmaStudio code programming.
Hi everybody, I'd like to know if SigmaStudio allows a small code programming solution. For example, I'd need to write Filter Funcionality of a Warped FIR filter, an iterative procedure of sums and pr