EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
adau1701 serial input and internal adc-dac problem
Hi I use I2S codec in slave mode, as specified in the datasheet: -If an external ADC is connected as a slave to the ADAU1701, use both the input and output port clocks. The OUTPUT_LRCLK (MP10) and OUT
-
Creation of Selfboot Image from Export System Files
So we have our hardware programming dongle as described in this thread: https://ez.analog.com/thread/19509 working and able to program the Selfboot Image as created from Sigma Studio into the DSP devi
-
Elements in schematic editor get corrupted/uneditable
Hello all, I just ran into trouble with my SigmaStudio schematic which unfortunately renders my project useless. All of a sudden the elements within one particular schematic pane are no longer accessi
-
Controllable amplitude modulation from sources & external
I would like to use the external control volume module in conjunction with the internal sources to create amplitude modulation. However I would like to control the gain somehow so if using a sine sour
-
How to optimiz ADAU1701 power consumption?
I noticed that 1701 will cost 85mA for analog and 60mA for digital. Is there any way to reduce them? Audio Signal Processors SigmaDSP Audio Processors adau1701
-
about usb_clk in EVAL-ADAU1701MINIZ
We have a EVAL-ADAU1701MINIZ board, when we check the schematic drawing, we find that usb_clk is a one-end net. It is pin 2 of J8. Where does it go? THanks. BR/Jackie
-
Best full range limiter implementation. - Adau1761
I am looking for the "cheapest" in terms of processing resources and memory full range stereo limiter for signals up to +24dB. The single limiter block is very expensive at 77 instructions\mips per a
-
Comb filter, feedback issue
Brett (and anyone else who might have some insight.) Several months ago, you and I had discussed a comb filter implementation. At the time, I was asking why the simulation/probe was not working proper
-
Long delay after a low pass filter ... what are the delay limits?
Hi everybody, I have a strange behavior in a simple workflow where, on an adau 1701 at 44100, a delay is put after a low pass filter. Nothing strange, it's a part of a more complex application, I trie
-
General (2nd-Order) Tone Control ... is it working in SigmaStudio?
Hi eveybody, I'm trying to use a 2nd Order filter as a "Tone Control", which is one of the possibilities in the drop down list. Nothing complex, a simple workflow working at 44100 Hz. What's happening
-
ADAU1701 Aux ADC Readback
Hi, I've got a system running in which a micro polls a readback cell in Sigma to read back the current level read on the Aux ADC. This is from an external microphone pre-amp and mic. I'm currently gen
-
ADAU1701 - Problem occurs when using S-DATA INPUT
hello. I have problem of when using ADAU1701 I2S. And i2s of ADAU1701 is slave mode. Master is MCU. however, this MCU is not bring to i2s function. So. I made self to LRCLK-OUT and BCLK-OUT, and S_DAT
-
Hilbert Transform and Quadrature VCO in ADAU1701
At the request of a psychologist friend I am working on theta and alpha binaural beat synthesis for encouraging relaxation and (possibly - depends on the research you believe) hypnotic susceptibility.
-
Relevant information isn't visible in ADAU144x hardware configuration screen
Hi, As a new user of Sigma Studio I was a little bit surprised of the visble information on the hardware configuration screen. If you look ont this screen you cannot see the settings, see the screen s
-
SigmaStudio Freeze Schematic Bug ?
Why Sigma Studio (3.8.2) action "Freeze Schematic" change the Export System Files ? after"Freeze" /* DSP Parameter (Coefficient) Data */ #define PARAM_SIZE_IC_1 1532 before "Freeze" /* DSP Parameter (
-
DIY USBi
Hello everyone! From the datasheet of USBi EVA board, I saw its schematic. http://www.analog.com/static/imported-files/application_notes/AN-1006.pdf Can i build a USBi follow the schematic? Do i need
-
SigmaStudio creation of selfboot image hex file
We are testing a prototype of a stand alone i2c programming dongle for our ADAU1701 project. The dongle takes the selfboot hex file created from SigmaStudio and stores several of them internally. A pr
-
External ADC and DAC for ADAU1701
Hello everyone, I am thinking about an idea to use ADAU1701 to make an active audio filter with 2 analog input and 4 analog output. The problem is that the SNR of the internal ADCs and DACs of ADAU170
-
Does Sigma Studio support anti noise apllication ?
Hi all, does Sigma Studio support anti noise apllication? application should be automotive to cacel noise created by car/engine, so about 20Hz to 10kHz? Which DSP and Codec should be used?
-
Strange output on biquad
Hi all, I've noticed strange behavior with the biquad blocks in a device that we'll be selling soon. It has an ADAU1442 inside. I've notice some output signal after a biquad which has no input (only a
-
Processor horsepower / instructions x cycle / load percentage
Hi everybody, I'm using Sygmastudio 3.8, I remember that some time ago there was the possibility to see the details about the generated program in order to understand how much of the horsepower of the
-
Safeload with DC Input Entry controlling 2nd Order filter /lookup
This question is about the opportunity to use safeload on an 1701 when updating a DC Input entry (that is a block controlling the index of the selected filter inside a 2nd Order filter /lookup). I'm a
-
Can I use 2 digital mics as input to my 1781 Eval Board
Hi all, my first post. I have a 1781 eval board and need to know how to set it up for 2 digital mikes input. I've read the AD AN and CN for attaching dig mikes to 1761, but it's alittle unclear (to me
-
SigmaDSP Part Selection
Hi all, I don't have much experience with digital audio, I am more of a digital control systems guy. However, I had an idea for a project recently that would really help me out. It's essentially a sma
-
ADAU1701 DAC DC voltage
Hi, I suppose to know that DC source block, in SigmaStudio, with value 1, should generate a full-scale output. So I expect to read at DAC output a full-scale DC voltage corrisponding to 3V (as it's wr