EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Distorted Sigma Studio Module
My group has been working with one sigma studio dspproj for some time, adding and tweaking various parts. Recently we found that whenever we add a module, either from the toolbox or copied from the pr
-
Using RMS compressor with peak detection sidechain.
I'm running low on instructions and would like to have the option of peak and RMS compression. I'm thinking I could use an RMS compressor with an optional peak detector on the external detect pin and
-
Dynamic changing of EQ presets based on volume potentiometer level
Hello, I would like to change EQ preset based on volume potentiometer levels. In reality it will boost bass (and other EQ things) in low volumes and when shifting the volume up the EQ should be more a
-
LMS adaptive filtering
Hello, I am with a 1701 third party board using SigmaStudio and I want to implement a Leaky FXLMS Adaptive Filter for feedback cancellation. I know I can design the filter itself using simple DSP bloc
-
Problem with using EVAL - ADAU1787Z
Hi, We purchased one evaluation board for the ADAU1787. I've been working on the evaluation board using the relevant guide and trying to make it work. so far unsuccessfully. I connected a microphone t
-
Seeking Help with AA-AP23123 Wondom DSP for Home Theater Setup
Hello everyone, I'm reaching out for some guidance on using the AA-AP23123 Wondom DSP, which is an unbalanced 2-In, 4-Out ADAU1701 DSP preamp with a 2-way digital crossover. I’m looking to use it simi
-
Write Biquad Coefficients through SPI
Hello, After uploading the schematic shown in the photo to the ADAU1467z, I exported the file and set it up to be remotely controlled via a Teensy 4.0. I used an SPI connection, and I confirmed that t
-
Dual Function momentary push button for short and long press
Hello SigmaDSP Community I was asked to solve a problem last week and I do not think the solution is anywhere on the forum. There is one post that is close but not exact. The problem is this: Have a m
-
ad1938 cracking
why crackles appear during audio reproduction through the ad1938 codec, and the audio also has extraneous overtones, as if there is a meander in the audio signal?? вт, 6 серп. 2024 р., 16:42 користува
-
AutoEQ - What Am I Doing Wrong?
I'm trying to create an active crossover. Started fooling around with AutoEQ. I have the Wondom DSP 2IN 4OUT 1701 board. Using Sigma Studio 4.7 Started with a simple sketch: Everything works fine. Add
-
ADAU1401A Noise level difference in case of Analog IN and Digital IN
Hi, ADI Support Team I am currently investigating the difference in noise levels at output between the analog and digital inputs of the ADAU1401A. When mute (No Slew) is executed during analog input,
-
Self Boot from external EEPROM using SigmaStudio+
Hi, I'm using the EVAL-2428WD1BZ board (rev. 1.1) along with SigmaStudio+ (ver. 2.2.0). I've been trying to configure ADAU1452 so that it boots from an external EEPROM (24AA512) but to no avail. I can
-
Using wondom adau1701 in PA Active speaker
Hello, I have some very basic newbie experience with sigma studio and wondom products.. im planning to build two way Active speakers with irs2092 amplifier and I'll like to use the simple cheap wondom
-
How to use DSP algorithm to avoid background noise with SigmaStuido Dev.Tool?
Hello, In one of my products,Mic input has a background noise of about -70dB from the hardware design. I want to use the following module connect to the Mic input to avoid this background noise. But t
-
Multiple External Potentiometers
I understand this DSP only has Four DACs, so I can only use 4 potentiometers in my SigmaStudio project. I am trying to use total of 7 external potentiometers to manipulate the audio coming in. Any sug
-
Help system quit working
My help system quit working. I'm sure it was working before. I have just tried uninstalling Sigma Studio 4.7, downloading again from AD and reinstalling but the help still does not work. By 'not worki
-
ADAU1701 negative fir coefficient values & ADAU1467 vs ADAU1701 comparison
Hello! I've been working to replace the DSP processor of a project that uses an ADAU1467 (using an evaluation board) to an ADAU1701 (I'm using a KABD 250 board that has an integrated amplifier). I've
-
Clocking for 96k Serial and ASRC inputs
I am working on a DSP processor that uses ADAU1452 for processing, with 16 total audio inputs and 8 Audio outputs; 8 audio inputs from 2x 4-channel ESS ADC in TDM4 mode, and 8 audio inputs from digita
-
ADAU1797 Compiling issues
Hello, I have recently received the ADAU1797Z evaluation board, as well as the instructions on how to run projects and the SDK. After configuring SigmaStudio+ and XTensa to run together, and loading t
-
SPDIF Rx/Tx Default LRCLK Polarity
Dear Team, We are using the ADAU1466 with Sigma Studio v4.6. We would like to know what is the default LRCLK type and polarity of the SPDIF Rx in the ADAU1466. Is it fixed always(like Negative or Posi
-
Two 'sine tone with phase and gain' generating the same tone are out of phase and maybe drifting, it seems to me. Why?
So if trying to make one 1k, 0 phase and the other 1k, 180 phase and sum them with the summer, they won't cancel. I find a phase where they cancel, but it seems random and it looks like it floats to a
-
Trying to understand Limiters and Sound Volumes
I am using Bluetooth (Wondom BRB3v3 Bluetooth Receiver) as input, which goes to DSP (Dayton Audio DSP ADAU1701), which goes to input of AMP (Wondom 2x100W Amplifier Board), which powers component spea
-
External button to select internal crossovers.
Hello everyone, I’m new to SigmaStudio and I’m working on programming the ADAU1401 to use an external button to select internal crossovers. I have successfully set up the blocks for external volume co
-
Attenuation in High Frequency without using any Filter
Hi, I'm trying to implement a crossover filter in th DSP ADAU1467Z. For checking the frequency response without taking into account any filter I measure with and without the DSP and I have found that
-
External SPI Delay on multiple channels shared with SRAM?
Dear ADI community, I'm currently planning to build an algorithm/architecture for the ADAU1466 where each of 8 outputs gets the option to set up to pretty high delay at 96 kHz (up to 1 second per chan