EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
adau1701 frequency response strange issue
Hi. I'm using an ADAU1701 with I2S input and DAC output as an active crossover. It takes I2S from a Bluetooth module with 6.122MHz BCLK and 96kHz LRCLK. It also has a 12.288MHz oscillator as master cl
-
How are you supposed to send an array using the ActiveX SigmaStudioServer in Matlab, using the REGISTER_SAFELAOD_ARRAY method?
How do you send an array using the ActiveX server to connect to SigmaStudioServer in Matlab, using the REGISTER_SAFELAOD_ARRAY method? I am absolutely flabbergasted that the following code excerpt doe
-
Will the ADAU1467 ever get Frequency Domain blocks in Sigma Studio
The original SigmaStudio toolbox wiki listed the ADAU1467 in frequency domain processing as of 2020, the draft updated front page has it removed. I'm just wondering if this functionality will come to
-
How can i get the VAD flag status on the evaluation board
Hello, i'm lit a bit lost with the use of the GPIO/MP and VAD flag block. Do you have any recommandation to know on the EVB if there is some voice acitivity in the DSP ? I'm interested to use any MPx
-
Sigma Studio
Can I use sigma studio with my custom ADAU1761 Board? or it can be used with Evaluation Boards only? Audio Signal Processors hardware SigmaDSP Audio Processors adau1761
-
Analog Devices - Pitch Transpose/Shifting Algorithm
My end goal is to create a real-time pitch shifting audio device (ideally polyphonic but I'm also fine with monophonic). I've done research about the different algorithms in time domain and frequency
-
ADAU1467 PLL
Hi I'm designing a DSP base on ADAU1467. I have some question about hardware and software. In SigmaStudio+ software Version 2.2.0. ADAU1467 IC settings, CLOCK CONTROL, there is a tab named CLK_GEN3 in
-
8 channels with 16 BCLK per channel
Hello, i need to communicate between the ADAU1467 and an I2S slave which supports 8 channels x 16 bits only. When i configure the Serial Interface 3, i can only select 8 channels with 32 BLCK per chan
-
Plugin making and dynamic memory setting
How can I make a algorithm plugin with dynamic data like Delay.That is, when i modifty the parameter, sigmatudio can dynamicly modify the memory allocated may be like "RepCount"? For example,when i se
-
AEC as a sidetone echo canceller
Hello everyone, In a very unconventional way, we would like to use an Echo Canceller to suppress audio sidetone from an analog audio intercom. Under normal circumstances, the audio intercom system com
-
Modifying saved config in an existing system
Hi, I'm looking at putting some active power amp modules into some of my passive loudspeaker systems. I've been able to track down some suitable "complete build" modules that should simply drop in to
-
Could sigmastudio export system file without hardware connection?
Hi , I'm a beginner and studying sigma studio. I wonder if I can export the system files (the C header files) without connecting to hardware? I tried the "Export system files" buttom and it showed tha
-
SigmaStudio+ Licensing
I'm looking for how SigmaStudio+ was licensed, and the proof of license or a license page. Where could I find this? I'm trying to find it before I install the application. Thank you
-
ADAU1701 - Sigma Studio
Hello, I am using the ADAU1401 to connect to a Raspberry Pi for audio output and crossover. I have referred to the MYDSPi project on GitHub but was unable to implement it. I would appreciate guidance
-
Mute (No Slew) Unexpected behaviour.
Dear Team , We are using the Sigma Studio ver4.5 and ADAU1466 board . We have the Sampling Fs = 192 kHz . The Code is a Simple passthrough code with Flow as described below: SPDIF Input -> Mute (No Sl
-
Help with Expander for SigmaStudio +ADAU1452
Hi, We use the Standard RMS module to aplly an Expander with the SigmaStudio on ADAU1452. As shown below. General understanding, we think the expander related to threshold.When the signal is weak and
-
ADAU1467 + DAC = Radio Frequency on the output
Hi, An ADAU1467 evaluation board is connected to a DAC board with ~15 cm ribbon cable (through ground). Spectrum analyzer connected to the DAC output shows 2 spikes (approx 430 and 215 Hz at approx -9
-
SSM I2C issue
Hi all... Good day, We are working on communication system using AD9361 with xc7z030. So I'm working with a xc7z030, vivado version 2021.1, and Vitis for Software. I2C signals read back from audio amp
-
Delay problems 1701 DAKB4100
Hi guys. Im new to using the SigmaDSP and I am using with the Dayton Audio KABD 4100 board which uses the 1701 DSP. And i am having huge trouble with the delay function. I understand that the only way
-
USBi driver Error 0xE0000243: The publisher of an Authenticode(tm) signed catalog was not established as trusted
I have SigmaDSP running on Windows 11 under Parallels on an M2 MAcBook Air. All seems well, except that the USBi driver will not install properly. I receive this message: "CyUSB.inf: Failed to add dri
-
Input to Output Latency on SigmaDSP Processors
ADAU1787 appears to have specified input/output latency, but other processors do not. What is the approximate input/output latency for the other sigmadsp processors?
-
SigmaStudio+ ADAU1452 unable to write EEPROM?
Hello, I've been trying for hours to get a board with an ADAU1452 and an EEPROM (SPI on the master of the ADAU1452) to run. My problem: With SigmaStudio 4.7 everything works perfectly. With SigmaStudi
-
Help with rotary encoder/ switch for ADAU1701 on Wondom AMP2 / DSPB-K DSP board
Hi, I have been struggling to get external switches or rotary encoders to work on the Wondom AMP2 when programming it using an IPC3. Whenever I connect up the switch or rotary encoder I cant get a rea
-
Microphone -20 dB stop
Hello, I'm looking for a block that doesn't allow a sound of -20db to pass through until it reaches -22db. I need it for a microphone because I use it for announcements and you can always hear the cli
-
Looking for Buffering & Time Stretching solutions.
HI ADI's One of my customers wants to implement the following functionality. 1. Digital audio input must be capable of buffering for up to 8 seconds. Since all audio inputs are 4ch (16bit & 48kHz), th