EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1466 i2s IN to i2s out
If you need to use the audio source i2s input port0, i2s output port1 How to set up in SIGMA STUDIO GUI? Audio Signal Processors software sigma studio 4.7 SigmaDSP Audio Processors adau1466
-
ADAU14xx / ADAU17xx I2S 24-bit LJ mode?
Hello, I am working on a project where I am using a CoolAudio 1401 / 1402 pair of ASICs which do ADAT En/Decoding. They only support a bunch of formats, for example 24-bit LJ or RJ mode. Here is the d
-
EVAL-ADAU1787Z USB Communication Failure Error
Dear ADI team, I encountered the same problem as below link, EVAL-ADAU1787Z USB Communication Failure Error How can I do now? Added pictures [edited by: ElvisJ at 3:11 AM (GMT -4) on 8 May 2024]
-
Tone control implementation
I, too, am trying to implement a simple tone control. The strategy described here, using indexed filters, seems very straightforward, but it hasn't worked in my hands. As best I can tell, I have the c
-
ADAU1466 AUXADC type conversion?
My 1466 eval board appears to have an issue with converting from into to float. When viewed in hex the values make sense but I am having trouble figuring out how to convert the ADC output to a float v
-
Does SigmaStudio have a real-time simulation capability using a wav file for input and PC sound card output, like in Audio Weaver?
Ive been using Audio Weaver to test out some DSP designs that will ultimately be implemented in ADI hardware. In Audio Weaver you can run the design and give it an audio file as input and hear the res
-
BCLK Settings, Sampling Point or Format Selection
Hello together, we have a question regarding the selection of the BCLK settings in SigmaDSPs. The best would be to share an example. SigmaDSP Serial In Settings: When we assume that we configured the
-
PeakRMS combo compressor suitable for low end (<40Hz)
Hi, I have been using the PeakRMS combo compressor in ADAU1701 with mostly great succes in many fullrange speaker projects over the years I use it primarily to limit too high levels below 120Hz - all
-
Compare available blocks for each device
It is my understanding that there are differing blocks available in SigmaStudio for each device. Is there a location that I can reference what is available for each device? All I am finding is the par
-
"Jitter" on any 'logic' or square/rect waveform, including library
Hello everyone, I am developing a set of audio synthesizer oriented modules. I need to add a variable PWM square wave, common in music synthesis. Just before turning the key on production I stumbled u
-
Feature Request: Sigma Studio connection over TCP for audio topology design
I just wanted to throw out an idea. Analog products are often used in embedded systems running Linux, Android (Automotive), QNX, etc. I think it should be possible to create a server that is programme
-
Sigmastudio+ Copy/paste doesn't include connections
Hey all. Copy/Paste in SigmaStudio+ 2.2 doesn't include any of the connections, and given some of those wires are not visibly explicit on each one, trying to replicate a large project is tedious. I ca
-
NLMS ANC
Hello, I have a question I want to apply NLMS I have 2 microphones. and I have a speaker, I give the noise in the system through the phone and I have an adau1467 eval board I want to apply NLMS and gi
-
ADAU1701 not discoverable when the programmer isn't connected
Hello, Just a quick problem. I'm trying to connect to an ADAU1701 via the I2C bus after a self boot. However running an I2C bus scan only shows the EEPROM. When I plug the programmer on the bus it bec
-
AD1953 Interesting SPI Behavior
Hello, I have an AD1953 project that I'm working on and have a question about how certain values are handled for SPI writes in certain scenarios. I am working on an amplifier/speaker project in which
-
C and asm programming in Sigma Studio
Hello, Is it possible to add my own DSP functions written in C or asm? I am using EVAL-ADAU1467Z. Regards, Roman Audio Signal Processors software 4.7 adau1467 adau1467z SigmaDSP Audio Processors Show
-
sigmastudio+ 2.2 turn off dark mode
How do I turn off Dark Mode in Sigmastudio+ 2.2? I can't for the life of me find the option, and the documentation is sorely lacking in navigability. software 2.2
-
ADAU1701 slave mode, move Fs from 48K to 96K
Hi! I trying to modify my old project. Old version, 48K ( MCLK = 12.288MHz , BCLK = 3.072MHz , LRCK = 48KHz) is working fine. But, new, 96K ( MCLK = 24.576MHz , BCLK = 6.144MHz , LRCK = 96KHz) sounds
-
Strong ringing while using 44k1 to 48k resampling block
Hi, I am preparing audio path in Sigma Studio in which I have 4 different sampling rate inputs from spdif (32k, 44k1, 48k and 96k), and I'm upsampling it to 192 kHz. I want to have different paths for
-
Need assistance on debugging a possible issue with merging the input channels and causing clipping
Hi, I'm debugging a strange issue with a crossover based on ADAU1466. I tried various settings in Hardware Configuration but running out of ideas, so appreciate if you can help root cause the issue. I
-
Sigmastudio+ 2.2 errors with filters
I experience unpredictable results using filters in SigmaStudio+. Below is shown two identical schematics. Each having two identical 2nd order bandstop filters, where one of them is muted. The output
-
[BUG] Issue in the calculation of the phase parameters for triangular wave phase
Hello, Just a bug report. I believe there is a bug in the implementation of the phase offset parameter calculation for the Triangular wave generator. From my understanding the phase parameter is encod
-
[BUG] Updating the frequency of the Sawtooth wave generator via the Sigma Studio UI doubles it
Hello, Just a bug report. If you make a program with a Sawtooth generator and let's set the frequency to 80Hz. Everything works as expected. If you update the frequency via the User interface after th
-
Volume control intermittent crackling
Hi, I am using this simple low pass filter with volume control and having issues with crackling sound when changing volume. This "crackling" is more like an explosion since it goes into 250W RMS sub :
-
Splitting Audio Signal into Upper and Lower Half-Waves Using Logic Blocks in Sigma Studio
Hello, I am seeking assistance on how to split an audio signal into its upper and lower half-waves using logic blocks in Sigma Studio. I need to send each half-wave to a different output. Could you pr