EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
communication and recording adau1701
Good morning! Dave, my program is now finally working, however, I am trying to update my program on the adau1701 through a microcontroller using the SPI, however, after my update I can't make my adau1
-
last stable 32bit version
Hello, I need an elder version of SigmaStudio for my programmer from Powersoft in 32bit for WindowsXP. Where can I find it? Thank you software
-
how to implement auto gain according to the frequency using ADAU1701
Hello all, we want to implement metal loss correction acc.to the incoming frequency. the adjust step is 0.1db/octave. I used the crossover to split the incoming frequency into low frequency and high f
-
phase reverse when compressor used
Hello All, I was learning the compressor and got some question. when the compressor was used, the phase of output reversed comparing with the input. shown as the snapshot below, using the project belo
-
ALSA Implementation Questions with adau1761 codec
Below are some of the dts I wrote. I want to implement ALSA by applying it as above, but the parts that are not applied well are as follows 1. ADAU1761 probe error occurred : : Unable to sync register
-
Syncing output to input using ASRC
I’m using the ADAU1466 running at a 48 kHz sampling rate for a project. I have a digital input that will accept either 44.1 or 48 kHz sampling rate, going through an ASRC at input to sync it to the DS
-
SigmaStudio software's register setup reference
The SigmaStudio evaluation kit user manuals include some great tutorials for initial setup. By using examples, they cover a great many details on how to use the SigmaStudio software interface to set u
-
Custom Platform setup and use in SigmaStudioPlus
Trying to understand what can be done with the SS+ Custom Platform feature. The help that's available is lacking in details. wiki.analog.com/.../defineplatforms I took an existing custom platform shap
-
LKFS Metering
I am looking into if it is possible to implement stereo LKFS Metering (or a close approximation of) in SigmaDSP. Here is the standard: https://www.itu.int/dms_pubrec/itu-r/rec/bs/R-REC-BS.1770-3-20120
-
ADAU1787 I2S output signal
Hi ADI's I am testing the I2S output of ADAU1787. Referring to the link below, I confirmed that I2S output is possible from the EV-kit. https://ez.analog.com/dsp/sigmadsp/f/q-a/570003/adau1787-i2s-out
-
ADAU1452 Linux driver
Hello! I would highly appreciated if someone could refer to an ADAU1452 driver for linux? Maybe exist a driver for another similar AD device which can be used as a reference? Thank you in advance! Bes
-
Sample delay for each functional block in Sigma Studio
Hi, I am looking for more detail about the implementation of each block outside of what the wiki supplies. I am specifically looking for sample delay of the signal in a block, if any. Some blocks I of
-
SDATA IN0 Port configuration as Slave in 'EVAL-ADAU1466' Board
While checking TDM16 output with 2 boards, below are the observation. TDM16 out in Board 1( SDATAOut0) -> TDM16 in Board2 (SDATAIN0) -> Not Working. For the restriction in routing data to SDATA In0 an
-
external ADC and ADAU1452
I have connected a simple stereo ADC : ADC Analog to Digital Converter WM8782 I2S 24Bit from https://www.audiophonics.fr/en/devices-hifi-audio-adc/adc-analog-to-digital-converter-wm8782-i2s-24bit-192k
-
ADAU1452 simple Sigma Studio Splitter
Hi Dave Thanks for any help. Chris said to ping you on this. I am new to sigma studio (ADAU1452) and try to get something super simple working. I have a single I2S input at 48KHz, 24 bit data, 32 time
-
RE: Usage of wav player module on EVAL-ADAU1452
Hello, I have tried the procedure with the file wav.zip from ADIApproved But it does not work on my ADA1452 Eval. When I download FlashProgrammer.dspproj , and then verify target memory I get : "Verif
-
Need to work with A2B. Got dsproj files for ADAU1761.
Normally I am a Linux user. I work with Yocto and the Android AOSP. Now I need to work with A2B, so I fought for a Windows computer to run SigmaStudio. I downloaded SigmaStudio 4.7 and installed it. H
-
Recommended Coax input circuitry
Does ADI have a recommended input circuit to interface 75ohm coax SPDIF port to the SPDIFIN pin on ADAU1467? I'd be interested in transformer coupled option to break any ground loop issues that may ar
-
Questions about implementing I2C for adau1701
Good afternoon! I am having problems using the ADAU1701. I'm trying to communicate (record it for the first time) with an STM32 via I2C, however, I didn't find a library (of stm32) that can help me wi
-
How to run the AD1938 codec on the EVAL-ADAU1466Z at higher sample rates
DOCX1466 passthru 192k.dspproj Audio Signal Processors adau1452 Audio Products hardware ad1938 Integrated/Special Purpose A/D Converters SigmaDSP Audio Processors Audio CODECs adau1466 Show More
-
How to interface Bluetooth module with ADAU1787?
Hi, I'm currently working on ADAU1787 development board, I trying to interface a Bluetooth module with ADAU787 development board. I would like to establish a communication via Bluetooth by using two A
-
Use both internal and external TDM DACs
I know I can't use both TDM and l2s devices at the same time. But what about internal DAC's and ACD's, and an AD1938 in TDM mode? If so, can I mix the 4 internal DACs and up to 4 of the 1938 DACs? Aud
-
SigmaStudio 'Help Wiki' - Have only been able to print *once*
Hello, At the bottom of the initial 'Documentation' page it states "....Pages from this Wiki can be exported by using the Print | Export Open Office | PDF options at the top of each page...." This has
-
EVAL-ADAU1466Z Poor ANC on White Noise and Speech
Hello, I am working on an ANC project for my internship, and I am having trouble getting the platform to cancel certain types of noise. With my current setup I am able to cancel tonal noise, multi-ton
-
Pin output sequence for power on and shut-down amplifier section
Hi guys. I would like to make a logical sequence to turn on the amplifier section with my 1701s. When I generate the start pulse (I use the encoder button) I need two outputs. The first output goes hi