EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Sigma DSP Audio Output Stops
Dear Team. I am trying to interface my ADAU1452 REV BZ board with another SHARC hardware as shown below: These are the settings in Sigma STudio . Issue occurs once I connect the GND or SDATAOUT0 pin t
-
sigmadsp_fwgen for ADAU1466
Hello, For a few years now we have a system with an embedded Linux that transmits through SPI the firmware to an ADAU1452 DSP. The firmware is made from the exported .xml then transformed with the sig
-
USBi programmer behaving abnormally
Hello, I am using USBi with SigmaStudio v4.7. I also have ADAU1701 mini eval board, and my own target board with ADAU1701, EEPROM socket and USBi interface header. The discription of the issue is as f
-
Stimulus&Probe works only once
Hello all, I'm using Stimulus&Probe to check the frequency response on ADAU1701, it works correctly when i click Probe button at the first time. but after closed the response window and click probe bu
-
ADAU1401 with PCM5102 DAC, BCLK missing
UPDATE: My scope was not good, later I managed to measure properly. DATA, LRCK, BCLK frequencies+voltages from the ADAU ok. But maybe i found what cause the issue: PCM5102 voltage pins: - pin 1 CPVDD:
-
ADAU1450 save parameters to the EEPROM
Hi everyone! I'm working on a very interesting project. This project is based on the dsp adau1450. The main board has 8 channels adc and dac. Also this project has one more board, it's remote board fo
-
Slave mode of clock for PDM interface
Hello. Everyone. Thank you for your help. I am trying to set the slave mode of clock for the PDM interface with ADAU1787. But what I can only find in SigmaStudio is the clock for the PLL. It will be m
-
Adau1467 signal level increases above a bitrate of 192 khz
Hi, When I use the ASRC with an inputsignal above a bitrate of 192 khz, the signal level seems to go up (3 or 6 dB). Suspect that signals values are shifted 1 or 2 bits to the left, but not quite sure
-
Query regarding Tone burst module
Dear Team, We require the following information regarding Tone burst module available in Sigma Studiov4.5 Toolbox. We have observed that there are two Tone Burst Generators : Sweep Log with (on/off) s
-
ADAU1860 "Lark Core" configuration for Windows Xtensa Tools
Hi there, I have a ADAU1860 evaluating board and I was be able to configure it and use of FDSP. Now I wanted to use the Tensilica HiFi 3z DSP that is on ADAU1860 chip. I have Xtensa Xplorer IDE instal
-
Bug with Simple Router with 5 inputs and sw slew selected, input 1 will chop off top half of waveform and input 5 will not pass audio to output
I am having issues with the simple router block. The block seems to have a bug when the sw slew option is selected. I have set up a simple example project below. I have a simple router with 5 inputs a
-
Communication between sigmastuidio and BF706
Title: Difficulty Communicating Between SigmaStudio and BF706 via Interface Protocol Description: I am currently facing challenges in establishing communication between SigmaStudio and the BF706 proce
-
Queries related to ADAU1472 Schematics
Dear Team, We have installed the Sigma Studio (v4.7) and need to check the HiFi input and HiFi output for SigmaDSP in 'ADAU1472' platform. We have followed the below steps, but while loading the schem
-
SPI Read Module for Block Shematic
Dear Team, The data in EEPROM memory can be read in schematic using SPI Read module. But in Block schematic there is no equivalent spi read Module. How to read data in EEPROM memory in block schematic
-
ADAU1467 eval and 6 I2S microphones
Dear developers, I am trying to connect 6 digital microphones to the adau1467 evaluation board. The microphones are all INMP441 on a breakout board. They are connected to SDATA, LRCLK and BCLK at IN0
-
RC slew options in Sigma Studio+ 2.0
I am confused on which RC slew option to choose. In the previous version of Sigma Studio 4.7 there seemed to be only one option listed as RC slew. In the new version of Sigma Studio+ 2.0 there are dif
-
Subwoofer DSP problem. Unstable Output with larger input
Hello, I am using sigma studio 4.6 to design a DSP for a subwoofer amplifier. My question mainly surrounds the limiter design. I am running into an issue where the limiter stops working correctly when
-
Is there a clean build type option
I had a project seem to get currupted and stopped build without errors. Is there a make or build clean type option? This sometimes seems to fix issues with other compilers when unexplained errors pop
-
Alias pins are causing issues
I am having lots of issues with alias pins. I created a designed that used alot of alias pins and when I try to open the schematic after closing the project the program seems to lock up and take almos
-
Is it possible to change the UID to match the Name of a block
Is there a way to change the UID of a block to match the Name that I changed? Audio Signal Processors adau1452 Audio Products software SigmaStudio+ 2.0 SigmaDSP Audio Processors Show More
-
ADAU1701 crash audio out plugged in. weard
I have a custom made unit which is micro controller run. it has 5V opamp filtering output. I recently designed a filter with gain however also used the design from the data sheet and it was the same.
-
ADUSB2EBZ
I purchased EVAL-ADAU1467 board which came with ADUSB2EBZ connection device. I installed it according to instructions. The correct LEDs are lit and the drivers installed seemingly correctly but it doe
-
Reading parameter data on ADAU1701 via microcontroller
I'm aware that the standard way for reading data from the ADAU1701 is via readback cells. But can I read parameter data I've written, just with I2C memory access? For example, if I safeload write a ga
-
Can SigmaStudio realize dynamic allocation of resource?
I am using ADAU1467 to make a AMP project. supply 32 outputs, and each output implements 31-segment EQ and 48DB/OCT high-pass/low-pass, which exceeds MIPS of ADAU1462. Can SigmaStudio realize dynamic
-
Can SigmaStudio be used to generate an EQ curve from a frequency response file?
I would like to emulate the frequency response of a loudspeaker using SigmaStudio. This is something like the opposite of Auto EQ where you are trying to use DSP to flatten an uneven response. Rather