EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1787 Matrix Multiplication?
Hello. I am currently working on noise cancellation for an earphone. I am planning to implement a custom Adaptive RLS filter for this task. I have the ADAU1787 Sigma IC evaluation board with me. In or
-
Adau 1467 Input 32/33 does not work
Hello everybode My adau 1467 does not work properly channels 36/37 work but 32/33 does not work i need but both for once a microphone and once for music can someone help me trying for the whole day Th
-
Execute-In-Place(XIP) mode support in SigmaDSP Processor
XIP mode, allows software code to execute directly from an SPI flash device rather than downloading the code and executing it out of RAM. In Sharc processor XIP mode is supported. Need to know the Exe
-
ADAU1787 can't output sound and can't detect sound input using line in.
I cannot get any sound to come out of the headphones. I have used a beep generator on all of the outputs but I cannot hear anything. I have a pair of headphones connected to the stereo out. I have the
-
ADAU1452 Hardware configuration, running without "Start Pulse"
Hi, I have a number of designs based upon ADAU1452 and I always have a green LED on MP0 pin which is flashed by a 1Hz oscillator to indicate the design is alive and operating. I assume that the ADAU p
-
csr867 i2s connection with adau1401 not working properly
I have a CSR8675 Bluetooth module with I2S output that is connected to my ADAU1401. Data is connected to MP0, LRCK to MP4, and BCK to MP5. I have then configured the GPIO in sigma studio. When I conne
-
ADAU1761 starts outputting noise at maximum gain
Hi! We have an issue with the ADAU1761 running FW created in SigmaStudio. The chip starts to output rather random signals at times until it has been reset, such as a sine tone around 1 kHz, but also a
-
Using ADAU1701 GPIO pins to switch multiplexer inputs
Hello, I have GPIO pin configured as 'Input GPIO Debounce.' On my board, I have this pin pulled down. All is fine if I connect this pin to an Adjustable Gain block with external control. Toggeling the
-
ASRC output rate setting for the Serial Output Port.
We need to configure SDATA OUT0 Port as slave. Hence, we need to configure ASRC for this output Port to sync with the external clock. Please confirm the output rate setting for this requirement. 'Use
-
On the problems of General Filters
Hello, I have a few questions about general filters: 1、What is the difference between the General (2nd Order) and General EQ (2nd Order) plugins? 2、In the Parametric filter, there are two Q. What is t
-
ADAU1452 + cs42448- No output
Hello, I an struggling in the attempt to get the output from a chinese board with ADAU1452 and CS42448 as a CODEC. I can get output from a white noise demo project (output 4 and 5 in my case). White N
-
Reading EEPROM Memory in Sigma Studio
Dear Team, We are using the Flash Programmer available as inbuilt module in Sigma Studio to flash a binary file into the EEPROM Memory. The EEPROM memory in the ADAU1452 Rev BZ Board is an 25AA1024 -
-
Unable to Read EEPROM after Flashing using Flash Programmer
Dear Team, I have an observation with the Flash Programmer module in Sigma Studio and the EEPROM Loader under Hardware Configuration. I flashed a dat file into Start Address 0 as shown below My dat fi
-
Flash Programmer for ADAU1452
Dear Team, I have some questions regarding Flashing a binary into the EEPROM of ADAU1452 REV BZ Board. 1. What should the Sub Address byte be typically? 2. The Start Address starts at 0 and increments
-
Sigma Studio: Can one potentiometer output to multiple blocks?
I'm attempting to connect a tone control (high shelf) to the same 'ADC In' as the volume knob. I want a little boost above 4khz when the volume is lowered. I can definitely do this using two knobs, bu
-
ADI有没有不需要MCLK的DSP型号,麻烦推荐一下
ADI有没有不需要MCLK的DSP型号,麻烦推荐一下 Audio Signal Processors adau1452 Audio Products hardware SigmaDSP Audio Processors
-
AD1838A Analog port protection
Do the A/D converter inputs have overvoltage protection above 2.82V p?? Or is it necessary to implement protection zener diodes at these inputs?? hardware Integrated/Special Purpose A/D Converters AD1
-
EVAL-ADAU1467Z Auxadc 50kohm
Hallo Have an Adau 1467z can i use 50kohm potis hardware adau1467z
-
Master Control Port and Parameter Update
Dear Team, While I see that Sigma Studio allows SPI Parameter updates via GUI / Capture Window , I actually want to update the same SPI parameters using the master Control Port (via the xml file ) . I
-
SigmaStudio 4.7 bug with Indirect Parameter Access Table using "Signal Invert" IC block
We are building a self-powered single driver (stereo mixed to mono) subwoofer using an ADAU1452 and SigmaStudio 4.7 to build our DSP. In order to create the typical subwoofer phase 0/180 feature, I ad
-
SPI Write and Read verification with different SPI offset address.
We need to flash the 'preset data' in specific offset address in the EEPROM flash memory and need to read the 'preset data' from flash memory in run time from the specific flash offset. Is this possib
-
KABD 4100 DIY project help
Hello tech minded people, I've assembled a sound box out of the old record player and now it's programming time. Tech I'm trying to dial is: KABD4100 2x1.1/8 silk dome twitters, 2x4" old Magnavox spea
-
Interface write block causing boot failure
Hi everyone, I'm working with a project that need change between 3 inputs, so I'm using a rotary encoder to do this job. The problem it's when I use a Interface Read/write block to save on my EEPROM t
-
asymmetricsoftclipper and advancedclip formulas are simply wrong?
KJBob Hello, some time has passed since fooling around with Sigma DSPs. I'm now busy with ML stuff. I'm trying to port some of the clipping algorithms that are documented here into a pytorch library.
-
Adau1467 expand I/O ADC and DAC
Dear sir/madam, As I am working with the Adau1467, I'm running out of ADC and DAC pins. For this application I would like to use at least 6 microphones, 1 audio input and 14 DAC outputs. I could use t