EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Dayton audio KABD-430 configuration
Is it possible to use all 4 DAC and the 2 DIG outputs at the same time on a KABD-430? I want to use a 3 way crossover where the output for the Hi go to DAC0 and DAC1. Outputs for the Lo go to DAC2 and
-
Connect USB interface without seflboot (ADAU1701)
Hi, in our product we use an ADAU1701 without selfboot, connected to a microcontroller that downloads the program at startup and varies some parameters during execution. In this condition (without EEP
-
ADAU1467Z- How to use Parameter update Block in Sigma studios?
I am trying to use the Parameter update block in Sigma Studio in order to dynamically change the delay parameter in my delay blocks such that I can create an adaptive beamformer. How exactly are you s
-
Tuned each channel for ADAU1452
Dear engineer zone Our Customer will use 7CH Channel digital audio output of ADAU1452 as a blow block-diagram. So, Can we adjust each channel for sound tuning? Can we use SigmaStudio of Tool if each c
-
ADAU1442 Feedback Suppression
Hello, I am new to posting here and also new to audio electronics; so my apologies in advance if my question is naive. I am designing a audio mixer amplifier and I would like to use the ADAU1442 or AD
-
EVAL-ADUSB2EBZ
good morning. I bought an EVAL-ADUSB2EBZ product and when I was using this product it disconnected before recording, then I had to turn the recorder's pci cable on and off, until it lit a blue led and
-
AEC ADAU 1467
Hi, AEC trial version gets muted In 5 minutes before 30 minutes (Documented). Block shows 88 seconds instead of 1800 seconds as shown in figure.
-
ADAU1701 ADC external resistor minimal value
Hello! I'm explaning all things but I would be glad if someone could just confirm or disprove the following third sentence ;-). I'm working on a wearable voice amplifier project for which volume and w
-
About MFxLMS active noise reduction processing
Hello: I am currently working on the active noise cancellation function implemented with MFxLMS, I want to achieve the goal of reducing the noise inside the car through this filter, but I encountered
-
ADAU1701, Initial state of GPIO, controlling MUTE on DRV632
Hi Forum I'm working on a ADAU1701 board, where I'm using DRV632 buffers as output filter from the DACs to ensure pop free startup from single supply. DRV632 has a Mute pin (pin 5) which is active low
-
Using the AD1938 DAC
Description: For a hearing therapy project I need to create a portable player that is capable of playing a wav file of 4 audio channels. For this, I am thinking of using the AD1938 DAC and an esp32-S2
-
ADAU1772Z power on issue
Bought ADAU1772Z board. I connected via EVAL-ADUSB2Z with the USB connector. But the target board (ADAU1772Z) doesn't power up. There are jumpers connected in J17, J10,J8,J12. The J3 jumper is connect
-
SSM3582 Amplifier wiring with ADAU1452 DSP
Hello, I am new to ADAU1452 DSP and SSM3582 Amplifier, I would like to design a circuit with with ADAU1452 DSP and SSM3582 Amp and program it by using SigmaStudio but I am confusing for the wiring in
-
Engineering Tools Questions
When doing signal processing with ADI, how do I know if the signal is up to snuff? I want to record a signal from start to finish, do I have to use an external acquisition program? Audio Signal Proces
-
[Bug Report] SigmaStudio2+ Pulse Generator, project doesn't compile
Tried everything but whenever the Pulse Generator cell is in the schematic the project compilation fails. The platform i'm using in the project is EVAL-ADAU1452MINIZ Edit Notes added platform informat
-
i need help with a plan for Adau1467 BBE Sonic Maximizer
would it be possible with an adau 1467 to simulate the function of a BBE Sonic Maximizer with integration of the Auxadc latest sigma studio version thank you would help me a lot greatings from germany
-
Can I use this circuit to use GPIO to control MUX ?
I want to use a GPIO to control a MUX in DSP. My GPIO connects to a hardware switch, when switch to SRC1 , it pulls high , when switch to SRC2, it pulls low. Then , I use this curcuit to control MUX i
-
configure Spdif receiver with ADAU1466
Is there any example project which add a Spdif input to ADAU1466 Schematic ? Can't find "Spdif Input " in SigmaDSP Audio Signal Processors spdif software V4.7 SigmaDSP Audio Processors adau1466 Show M
-
Multiple ADAU1772's and MCLK
You liked running the ADAU1772 as a slave off the APx55 MCLK. I actually saw worse S/N doing that, but anyway, what if I have multiple 1772's all driven off a MCLK sent by an FPGA. Is this better than
-
(adau1451) How to make sure EEPROM settings are correct? if "Check last compilation throught DSP" always retrun fail.
Hi~ I am using adau 1451 design a car audio product. We had made PCBA, using adau1451 pin 28 (SCL ), pin 28 (SDA) to connect self boot EEPROM (AT24C256). pin 28, pin 29 using 2.2k resistor to pull up
-
EVAL-ADAU1467Z Auxadc
hello need help how do i connect a potentiometer to an auxadc but where the other two pin Audio Signal Processors hardware adau1467 aux adc EVAL-ADAU1467Z SigmaDSP Audio Processors Show More
-
ADAU1701 (JAB4) ADC values incorrect and changing
I'm using potentiometers to provide basic loudness/tone functionality in my project and have come across a problem I'm not sure the best way to solve. Project is attached. The issue is that the value
-
Rotary Encounter Write with MCU not working
Hey guys, I am failing in setting the rotary encounter volume externally with an MCU. This is my DSP Program: This is my xxx_IC_1_REG.h file contents: Now when do a I2C read on that Register I get bac
-
How to change the SW slew value in Sigma Tool
Hi, Let's take RC Optimized Single Volume as an example. My question is how to change the SW slew value (RC alpha value) in the Sigma project. I didnot find any interface to change it in the Sigma too
-
active two-way speaker with 1701: help for loudspeaker management and protection
Hi all, I built an amplifier module for an active two-way speaker with powersoft digimod 1500. I would like to create the firmware to better manage the speaker by protecting the speakers so that they