EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
No output from secondary sound source during MFXLMS training
During MFXLMS training, the secondary sound source can emit sound normally. After saving the secondary channel coefficients after training, go to the control page, download again, and turn on the cont
-
Level Detector
The signal detection is negative, can it be understood as a positive value? Does - 45dB represent 45dB? I don't quite understand. I am using the MFXLMS module to conduct a sound pipe noise control exp
-
wondom jab 5 sigma studio 4 way sound system Funktion One res 2 scale prj
Hi guys, i'm pretty new to Sigma studio. I had read a lot from web and create my dsp design but probably I'm wrong in which parts. The project is a 1:6 scale Funktion one system, consist in one double
-
MxFLMS
Do I want to use the MFxLMS algorithm in ADAU1452? Now there are two questions? (1) How do I know if secondary channel modeling is successful? How long does modeling need to stop? There seems to be no
-
Graph
I use a graph to display square waves, but instead of showing square waves, it shows triangular waves? Does this module appear to have errors? "I want to show the changes in this signal, but obviously
-
ADAU1701: is 44.1Khz a supported rate for the I2S Serial Data Input?
Hi all! I've designed a (in my opinion ;)) very nice DSP board where a Teensy 4.0 and a ADAU1701 can work in tandem for audio effects. However, I'm having some struggles to get sound between the two.
-
numerical simulation
Can SigmaStudio do simulation without the help of hardware ADAU1452? I now have a 70MB voice signal. I need to perform voice enhancement (filtering and noise reduction) on it, and then save the output
-
ADAU1772 REGOUT and DVDD
Please discuss design options with REGOUT and DVDD and how they should be bypassed in each case. Its a little confusing. adau1772 Integrated/Special Purpose A/D Converters Audio CODECs
-
Use Clickless HW Slew General EQ (2nd order) Slew Parameters Were Not Saved Successfully
Open any sigma studio project, modify the general_eq(2nd order) of slew type parameters, save, and exit. Open the project again and the slew type parameters are not saved successfully. Audio Signal Pr
-
ADAU1787 measure the transfer function between speaker to microphone
I am working with the ADAU1787 and SigmaDSP. I need to measure the transfer function between the output and the input of the device. Is there a way to record and upload to the PC the white noise outpu
-
Schematic and BlockSchematic
What is the difference between Schematic and BlockSchematic? I found that they support different modules. How can I use them together? The tutorial on the wiki is an old version of SigmaStudio, withou
-
SigmaStudio tool with ADAU1772
I am experiencing issues with SigmaStudio where when I am setting parameters in one tab of the IC 1 - ADAU1772 Register Control section it changes settings in others - specifically the Signal Routing
-
ADAU1701 Eval board development related.
Hi, After multiple failed attempts, I was finally able to successfully build ADAU1701 eval board. However while I was building the existing circuit I struggled a lot with VDRIVE and 1.8 voltage on pin
-
Adau1452 Hilbert Transformer doesnt work
Hello Friends, My Problem is, i have tested in Sigma 4.7 and 4.5 with adau1701 and 1452. no signal goes through the Hilbert block. inserted into existing project, no success. new simple project create
-
Variable step size LMS
Is there a LMS module with variable step size for SigmaStudy? I need to use it. Audio Signal Processors adau1452 anc software sigmastudio SigmaDSP Audio Processors sigmastudio4.7 lms Show More
-
ADAU1772 Output ASRC Source Select
Please explain the Output ASRC Source Select. I have been using the Core Out X selections but wonder about ADC X selections. They do not seem to have the same levels as the Core outputs. Are they basi
-
Multiple definitions in IC_1_PARAM.H
Hi, I have seen that when I export my project so I can integrate it with my mcu code. I am getting multiple definitions in "IC_PARAM.H" file. I have a made a very basic project to show the issue I am
-
No output
我设计了一个正弦波模块,接0通道,可是我接耳机听没有声音?我用的是ADAU1452和SigmaStudio4.7,我是先编译下载,然后写入内存,可是没有输出? Audio Signal Processors adau1452 hardware SigmaDSP Audio Processors sigmastudio4.7
-
1-in / 4-out crossover using Dayton Audio DSPB-K DSP
Seek suggestions on a 1-in / 4-out crossover using just the Dayton Audio DSPB-K board (and not the KE daughter-board). I'm considering a low pass filter for a large woofer, a high pass filter for a tw
-
ADAU1401 I2S Input and Output Trouble
Hello, I am trying to build a Bluetooth speaker using an ESP32-PICO utilizing the A2DP library as my source. The end goal is to send the audio signal from the ESP32 > ADAU1401 DSP > I2S Digital Amp, a
-
EVAL-ADAU1467Z
I want connect the two stereo inputs to the EVAL-ADAU1467Z unit in inputs 32-33 and 36-37 . When connecting input to 32-33 Through the EVAL-ADAU1467Z in J14 I heard the outputs well. See the sigma stu
-
Which SigmaDSP for a fun project?
Hello everyone, I am new to this forum. I'm an electronics engineer and I plan to make a "fun" audio board for my sons. At this time I haven't listed all the specs this card should meet, but primarily
-
Master Control Port XML works in realtime link-compiling but not after boot
Hi, I need a help with my SS project: I'm using a Master Control Port Boot to write some register configuration to my ADC and DACs When I use it in realtime link-compile-download, works very well, but
-
ADAU 1467 Bush Button Volume Control with GPIO
I am using the EVAL-ADAU1467Z and I am trying to make the 'PushButton Volume, Mute' block work. Schematic: Multi Purpose Settings: I use the MP pins 18 and 19 of the eval-1467 board. The push buttons
-
Module underlying source code
How to get the underlying code of each module of SigmaStudio? Audio Signal Processors adau1452 sigma studio software sigmastudio SigmaDSP Audio Processors sigmastudio4.7 Show More