EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
importing custom dll's made for sigma studio into sigma studio plus (sigma 300)
Is there plans for extending the ss+ algorithm designer to support sigma 300 chips? I have a few custom algorithm add-in's that i was using with sigma studio 4.7, i want to migrate to sigma studio plu
-
Setup a software controlled DAC/ADC through i2c with ADAU1466
Hi everybody, I'll detail the board as much as I can: So, the board have a ADAU1466, 4x PCM5122 and 1x PCM1865, both ADC and DAC are software controlled through i2c, with its respective addresses corr
-
ADAU1701 exciter
The exciter generates high-frequency components that are not part of the original signal. It is achieved by using nonlinear distortion processes similar to those used to produce overload and distortio
-
SigmaStudio for EVWSS
Hello, I am completely new in SigmaStudio, I would like to develop a electric vehicle warning sound system using SigmaStudio, It will be very helpful you guide me how to start on the same. Thank you
-
Problem while flashing the ADAU1452 through I2C
Dear Sir or Madam, I'm currently trying to use the ADAU1452. My purpose is to flash a program into the ADAU1452 in I2C using a MCU. I've validate that it was possible with the eval board (I'm able to
-
ADAU1401/1701 : I2C ADDR1 bit clarification in datasheet
Hello, I have a potential datasheet update/clarification request for following products : ADAU1401 ,and ADAU1701 , regarding the ADDRx inputs. I have a PCB with the following connections : ADDR0 tied
-
Another 1787 PDM question please
I'm trying to implement a very simple setup: PDM mic inputs on the ADAU1787 eval board to an analogue output, see this project:1787 PDM TEST.dspproj Problem is it isn't working. I've read the previous
-
ADAU1701 - Using Switch on Potentiometer/GPIO Headers
Hey guys! I'm develloping a custom plate amplifier using the Dayton Audio KABD-250 and 430 and I'd like to use a switch on potentiometer/GPIO Headers on the board to use as a stereo/mono selector. How
-
Subwoofer limiter
Hello everyone, I am new here and not familiar with DSP, but I found my way using the sigma studio, I am building my own subwoofer using 18” woofer 1600w rms and I got the powersoft Digimod 2000HV wit
-
Is it possible to program the ADAU1462 without an EEPROM?
I'm getting started designing a board with the ADAU1462 and I'd like to avoid adding an EEPROM on board if possible and instead opt to program it from the microprocessor that acts as its I2C controlle
-
ADAU1452 Sigma Studio Input Block TDM slot/channel mapping
Hello, I have trawled the help files and this forum looking for a definitive answer to the question about TDM slot input mapping channels to the Sigma Studio input block. The help file suggests that i
-
ADAU1452 Slave Microcontroller port & USBi
Using a Teensy 4.1 to control ADAU1452, so the tutorial written for the Teensy 4.0 is really helpful, thanks. My workflow is to develop and test the Sigma Studio design and use a USBi interface to loa
-
ADAU1452 PLLFILT application Consult
Hi ADI Tech Support, Some questions about the application of ADAU1452 need to consult, thank you! 1. Currently, the description of PLLFILT foot connection is not very clear in the specification. Pleas
-
ADAU1452 spi extern delay module do not work
I use SPI SRAM (23LC1024) connected to the master spi interface of 1452, and test the sigma studio module. But I found that it do not work well. the audio playing back is not right. the sigma studio p
-
Audio IN\OUT format realtime change
Hi, I'm new to ADAU DSPs, still reading the datasheet and playing a bit with Sigmastudio. My question for the moment is very simple: is it possible to change data output format and sampling frequency
-
Could not change E2PROM Properties
Hello, I have ADAU1701 and ADAU1452, in one design. When I try to edit IC2 properties it always show IC4 properties. My changes could not be applied. Audio Signal Processors adau1452 software 4.7 Sigm
-
What is actual sample rate of ADAU1701
Hello, I made simple loop-back circuit: ADC -> DIG -> DAC and observe correct behavior. The circuit works at 48 kHz. But when I connect input to 20 kHz input sinus I see more steps then expected. It i
-
Variable input level - constant output level
I was wondering if it would be possible to come up with a circuit that could convert any input level to a fixed output level in real time? Audio Signal Processors software TSA1701 sigmastudio SigmaDSP
-
PCM to PDM conversion
Hi, I bought an Evaluation board based out of ADAU1772. As it was mentioned in other blog that it can be used for converting PCM to PDM, my question is there is CLKOUT for PDM output stream. Is there
-
Generating clean sawtooth waves with ADAU1701
I would like to generate a sawtooth wave that: A) Has accurate enough pitch control to be tuned with a precision of a few cents on a musical scale B) Is free of aliasing I have gotten each of these re
-
ADAU1452 incoming I2S slave clocks routed to I2S slave output
Hello All, I have the ADAU1452 DSP being slave on one of the I2S inputs and on one of the I2S outputs. MCLK is fed by a crystal. Physically the master is connected to the BCLK/LRCLK/SDATA_IN0 and SDAT
-
ADAU1452 slave/master I2S communication, clock routing
Dear All, I am working on a project where the ADAU1452 needs to receive I2S data from an MCU (MCU is master towards the DSP), from an ADC and a BT module (they are slaves towards the DSP). After recei
-
Need assistance creating ANC workflow
HI all, I struggling to build an ANC workflow in Sigmastudio on my ADAU1463 board. Im sure im setting up the workflow wrong, as im also a little unsure as to how i should be connecting the pins to the
-
Input/Output management on ADAU1467 with SigmaStudio
Dear Sir or Madam, I'm using the ADAU1467 and I'd like to use it to communicate through I2S. How can I use Sigma Studio to choose which I2S input/output to use ? For now I'd like to receive data from
-
MCLKI current draw when PVDD/AVDD off (ADAU1701)
I noticed an oddity with this device. For my design, I have to turn off AVDD/PVDD in standby due to a power-hungry codec elsewhere. This keeps us in compliance with standby current. Trouble is, with P