EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Interface Status saved
Hello, I have read the Article about the Interface write back to EEPROM. I have currently a problem where I switch 2 signal sources with push button, very simple. But as it was stated that the WRITEBA
-
Soft clipper in the ADAU1787 fast DSP
The toolbox for the ADAU1787 fast DSP does not include a soft clipper, yet it seems possible to implement a standard cubic soft clipper with a set of more basic toolbox elements (I can send a SigmaStu
-
ADAU1452 board identification
Hi, I have an "old" DSP board that I can't identify. Do you know what is it ? I can't find any informations about it... Thanks. Audio Signal Processors adau1452 DA3088 hardware sigmaStudio 4.7 SigmaDS
-
GPIO
Hi, I am working on ADAU1787 evaluation board. I am trying to configure MP pins as GPIO. I am trying to enable/disable output with external switch. Is there anything wrong. GPIO.dspproj software ADAU1
-
Two Significant Question
Dear Team , I have two questions pertaining to the Sigma ADAU1452. The first one is regarding the Parameter RAM that is visible in IC params window . I have some contents in an external Flash Memory I
-
Unable to access AD2420
I am new to Sigma Studio. I want to use AD2420 with Sigma Studio. I have connected it to my desktop using Ethernet. But, still it is not showing up when I start a new project in Sigma Studio. Please l
-
Analog mic connection
Hi, I am working with ADAU1787 Evaluation board. I am trying to connect analog mic. microphone image is shown below. i connected it to AIN0. there is no output at speaker. is there anything wrong in c
-
Options to Increase ADAU1701 Output Voltage
I am using a Wondom ADAU1701 set for an active 4-channel diy amplifier with TPA3255 chip. I know the ADAU1701 suffers from an output voltage of 0.9 V(1 V), and the TPA3255 accepts voltage up to 7V. Ca
-
Can't communicate via i2c with my ADAU1701 design
I'm using a custom PCB to have Particle Boron (an MCU that works similar to a Arduino) communicate with a ADAU1701 DSP via it's i2c port. I've gotten my firmware to run and communicate between a Boron
-
ADAU1467 input selector toggle switch
Hi All, I'm on ADAU1467 and like to make an input selector using a momentary normaly open switch. On the board, I use "MP14" pin for the switch input and GND. 3 stereo inputs are availables. There is
-
How to use ESS TOOLBOX in SigmaStudio (4.7)?
你好 : Does ESS TOOLBOX have examples and structures for reference? I can't find relevant explanations and uses? Can you tell me how to use it? Is it AUDIO ENHANCEMENT? Thanks Jack Wang software sigmaSt
-
ADAU1452 - Upsampling cuases wrong smpalerate at Delay
Hi, I'm using ADAU1452 in a project with 48kHz. Because I need shorter delays than 20µs (=1 Sample @ 48kHz) I change the sampling rate via up samling V1.02 e.g. to 96kHz. For further editing I c
-
ADAU1463 DC=123456, Readback=114688, why?
Hi ADI Engineer I wont to read back value from a DC but it's wrong! I try other values of the DC and all is wrong, 123456 -> 114688, 123 -> 116, 0xFF -> 0xFE... I try SigmaStudio 4.7, 4.6 all same pro
-
I have ADAU1452 schematic that I need to run on an ADAU1451. Do i really need to redraw the whole schematic?
I developed a fairly large algorithm in SigmaStudio, which runs with about 90% instruction / cycles (just to give some indication of it's size). I've been testing / running the code on the EVAL-ADAU14
-
-- How to have a long delay with ADAU1966AZ, and other questions --
Hi there, I'm Maurizio from Rome, Italy, I'm beginning to use Analog Devices boards but I'm a newby in such a world, therefore please forgive me if I'll not be too clear: moreover, english is not my m
-
ADAU1467 I2S IN/OUT (ASRC)
Hi All, Coming from ADAU1701, I need more channels and want to not use any internal ADC/DAC. I'm builbing a 4.1 audio amplifier. 3 inputs are needed: -Bluetooth -Stream Spotify from ESP32 -Analog IN S
-
Sigma DSP Setting SPDIF_TX_CS Registers
We are manually setting both the LEFT (0xF6A0 to 0xF6AB) and RIGHT (0xF6B0 to 0xF6BB) SPDIF_TX _CS registers directly from the register map. In our case we have SPDIF_TX_ AUXBIT_SOURCE (0xF69F) set to
-
ADAU1452 + SPI EEPROM after reset power not load Multipurpose settings
SigmaStudio source program audio proceses and MP6 pin configured OUTPUT for LED and the program was wrote to EEPROM, all working good, LED blinking. After reset POWER, DSP start program from EEPROM, a
-
ADAU1467 internal WAV Player
Hi all I want to use two internal WAV players on an ADAU1467. Unfortunately I get the following error message: ##### Compile Started: Monday, July 4, 2022 5:14:25 PM ##### error (6075,Gong1): Label 'S
-
ADAU1452 connect with other device in another board
Hi, I have a hardware problem now. I use ADAU1452 to receive datas from ADC in another board, ADC refer clocks and datas. The ADC board and 1452 board connect through a FPC line. All the system can wo
-
Sigma Studio v4.7 Export System Files Not Working
Just recently upgraded to v4.7 of Sigma Studio. When I go to export the system files the following outputs are created but have 0 Bytes associated with them. Basically blank. .params XML .h PARAM.h RE
-
conditional switching
Hi, I want to achieve following: If the input goes to one, the output will go to one, then if the input turns into a "0" , the output will have to go to "0" without delay or hold. Then the output must
-
AutoEQ on demand - using ESP32 as TCP/IP channel server
Hi, I incorporate [AutoEq](github.com/.../AutoEqhttps://github.com/jaakkopasanen/AutoEq) and use ESP32 as TCP/IP channel server for "AutoEQ on demand". Please see: 1. [AutoEQ to flat line](https://you
-
SigmaStudio 4.6 - ADAU1787 - Export without download, other issues
ISSUE 1: I generate my register settings blindly to run on other target hardware without the need to download. If I want to Export meaning the Action -> Export option is not greyed out I have to first
-
Timer in adau 1467
Hi, I want to utilize timer in adau1467. Requirements: If input=1, output=1 (without any delay or hold) If input=0, output=0 (output stays at zero for 30ms no matter whatever input is). Audio Signal P