EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1701 issue, FILTD
I have a problem with the ADAU1701, it is working on active Electrovoice and FBT booths working in selfboot mode, it starts working fine but suddenly it starts to generate a noise and the audio fades,
-
Clock Setting
Hi, I am working on ADAU1467. i don't know ADAU1467 kit is running at full speed. how to do clock setting in sigma studio. Thank you
-
ADAU1452 Detecting the end of a slew-rate limited mute transition
Hi. I have a mute block with a custom slew type (0xAAAA), which gives me a slow fade to mute over about two seconds. Rather than hard-coding the transition time in the MCU, I'd rather get this informa
-
If channging the samping frequency all fiter values are wrong. Did I miss a parameter ?
Hi I have the problem that if I change the samling frequency for example to 384kHz, I have to manually calculate all filter values 8X and enter them like this. So a high shelving filter of 4000Hz woul
-
Sigma studio "Link compile download".
HI. I create a project that run in ver 4.5 in my previous computer with no problems. When I switch to my new computer and install sigma studio ver 4.6 , i open the project ( which run on my previous c
-
GPIO controlled switch
Hello: I would like to implement a Sigma DSP ADAU1701 Digital audio switch the would be controlled by GPIO inputs siiler to doing it in analog like this. Any Ideas? Thanks Audio Signal Processors soft
-
ADAU1401A: can it use both TDM and I2S inputs?
Hello, I would like to know if I can configure the ADAU1401A to receive data from a 8-ch TDM stream (only 4 channels, at the left part) on SDATA_0 and 2 additional channels in I2S format on SDATA_1. I
-
ACTIVE NOISE CANCELLATION
Hi, I am trying to do active noise cancellation. can i use ADAU1781 for ANC. please suggest best DSP for active noise cancellation. Thank you Audio Signal Processors software Rev 1831 4/5/2022 adau178
-
EVAL - ADAU1788Z issues
I have received the eval board and am currently testing it. Channel 0 works ok but channel 1 gives no output at all. The second problem is that the fast processor does not appear to be supported at al
-
Real time display
Hi, I am working on ADAU1467 evaluation kit. i am trying to draw graph of sine tone that available in sources. but it shows noise only. Thank You when i connected DSO then it did not show sine wave. [
-
adaptive filters
Hi, i am working on EVAL-ADAU1467Z evaluation board. I am working of filters. is there any documentation available on adaptive filters and their use in sigma studio. Thank you
-
ADAU1463 index selectable demultiplexer
Hello everybody, I have a quick question about the index selectable demultiplexer block: Index Selectable DeMultiplexer [Analog Devices Wiki] What signal is on the outputs, that are currently not sele
-
Custom Linux board with ADAU1701: ANC + Capture + Playback
Hello all, Currently, we are working on a custom Linux board with ADAU1701 and NXP i.MX6SLL series processor. One of the functionalities of this board will be to apply ANC to the user's voice streamin
-
ADAU1452 FIR TAP count
Hello All, I was wondering, if I have programmed a DSP application, containing a FIR with 6000 taps, is it allowed that I change the tap count afterwards in, for example, 300 and upload 300 new co&eum
-
Add multiple pdm mic
Hi, i am working on EVAL-ADAU1467Z evaluation board. i need to connect multiple PDM mic. i connected single mic and it is working properly. can you tell me the way how i can configure multiple PDM mic
-
ADAU1772 - Output Noise level in balanced vs Single-ended
Hi, I am using the ADAU1772 codec to drive low impedance headphones (8 Ohms) for ANC and therefore I need an external amplifier between the codec and my headphones. This additional gain raises the noi
-
ADAU1761 DSP Bypass
Hello, I'm searching for AN-1007 Application Note, Using the ADAU1761 in DSP Bypass Mode to Emulate an ADAU1361. Thanks.
-
issue with code saving
hi, i am working on ADAU1467. issue i am facing is when i power off the switch. i need to code it again to make it work. whenever i power off the switch code got washed. Thank you
-
USBi not recognized but was in the past
I am testing codecs on several eval boards we purchased. ADAU1702MINIZ, ADAU1401AEZB, ADAU1772, and ADAU1787. I was successful testing all but the ADAU1401AEZB. The USBi would not become recognized an
-
How to trigger the E2Prom.Hex generation using the API
Hello out there, I try to control my SigmaStudio Installation using the SigmaStudio-Server-API. The API is described here: SigmaStudioServer [Analog Devices Wiki] Currently I try to export the E2Prom.
-
Upload e2prom to file does not work in Sigma Studio 4.5
Hello, I have a problem with E2PROM window, because I try to upload datas from E2PROM to file, but the file does not creating in the folder what I gave in the "Click here two browse for file" window.
-
Testing ADAU1772 Serial I/O using APx555
I have a loaner Audio Precision APx555 analyzer and would like to test the converters of the ADAU1772 using the Serial I/O. I am using the ADAU1772 eval board and am not able to get the Serial I/O on
-
ADAU1466 T Connection Latency
Hi, I have a problem with a project for ADAU1466. I have detected a latency difference between two channels of 1 sample. I have been reducing my schematic until I find the problem and I have found it
-
Issue with ExtSPIDelay on ADAU1452
Hello, We are using the development board for the ADAU1452 because we need to implement a big delay (we expect to be able to delay our sound up to 35 seconds). I am trying to use the functionality but
-
ADAU1401 I2S slave
Hi, I am a non engineer, so I want to make an audio effect using adau1701/1401. but because there is no long delay available, I want to connect it to teensy via I2S connection, but I can not found any