EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
GENERAL FIRST ORDER FILTER
Hello. I am using frequency filter in Sigma studio. Some parts were not explained in the calculations and I was not sure. I do the calculations but it doesn't work. Can you help with the calculations?
-
This is a comment for the help subject "How do I execute a software safeload write?"
This comment is related to How do I execute a software safeload write? Since I can't add a comment to that page, I decided to create this message. First, that informational topic talks about safeload
-
digital input stereo separation in adau 1761
Hello, I am using ADAU 1761 on SigmaStudio 4.6. I am playing a stereo signal from a bluetooth module (BC127) wired to the ADAU. In SigmaStudio, I am therefore using the digital input (input 2/3) going
-
IIR filter coefficients for 50Hz notch
Hello, I am using ADA1761 codec with 48kHz sampling rate. My SigmaStudio project contains the second order double precission IIR filter for which I deliver 'a' and 'b' coefficients calculated in Matla
-
Limiter
Hello. I'm trying to make a limiter. When it reaches the limit, I want to light the external led. When I use the limiter, the limiter does not work. I don't understand the calculations on the site eit
-
ADAU1467Z Rev B Mount Hole Dimensions
I'm hoping to make a mounting plate for this processor, but I'm struggling to find a dimensioned drawing of the board anywhere in the data sheet (specifically for the mounting holes). I was wondering
-
Compiler Error
Hello. I am using Adau1701. I keep getting the following error when I add some blocks. For example, I'm using a limiter. I am doing it according to the rule as follows. What is the problem? I can't pr
-
Medium Size EQ
Hello. I am doing tone control with Sigma studio. The schematic below works for me. It works the way I want. I want to control it with the processor. I don't understand how it generates these 5 datas.
-
Problem initializing ADAU1466 by software
Hi, I have a hardware design with an ADAU1466, connected to a dsPIC Microcontroller through an SPI port. I generate the files for the C language directly with SigmaStudio (I am using the latest versio
-
ADAU1777 I2S output
Hello, When I use adau1777 serial output ports, I encounter some confuse problem. When I configure I2S SAI as below. the first channel data miss. When I configure the LRCLK mode as Pluse, others is sa
-
How do I use SigmaDSP to send all zeroes to the DAC of ADAU1772?
I am using the ADAU1772 evaluation board and want to measure SNR using my QA401 audio analyzer. I'd like to know if SigmaDSP can force all zeroes to the DAC. I am not using any modules in the SigmaDSP
-
ADAU1463 TDM16 in slave mode
Hello, We use the ADAU1463 in a system with TDM16 signal 24/32 bits on 48kHz on Serial Port 0 from a FPGA but the dsp is not working correct as slave from this input 0. Every time the systems starts t
-
ADAU1701 Analog Ground Plane
I'm designing a 4-layer board with the ADAU1701. On the board is also: Buck regulator for ADAU1701 digital power Linear regulator for ADAU1701 analog power Linear regulator for op-amps Op-amps for inp
-
Eeprom programming is Adau1452
We have been developed Class D power amplifier using adau1452 DSP for audio signal processing. We used the same SPI eeprom 25AA1024 (for self boot) as it is in Evaluation board connected to DSP via SP
-
Any Engineer that can help with ADAU1701
Hi There, I am just going to ask this question again as previously i had been unclear, Just some background below. Portable Bluetooth Speaker with DSP Trying to implement a 5 band Graphic EQ in sigma
-
Interchangeability of ADAU1452/1451/1450 and ADAU1462/1466
Hello, As said in ADAU1462/1466 datasheet, it seems to be compatible pin to pin and in registers to the ADAU1452/1451/1450. I would like to know if this is really true and (with a reduced signal proce
-
SigmaDSP control from a micro - is there an update to "Basic SigmaDSP
Microcontroller Integration" ?
I'm trying to help someone get a SigmaDSP integrated with a microcontroller. Specifically how to control the parameters of the blocks in the diagram. Code download is working. If it makes a difference
-
SigmaStudio Simple Graphic Equaliser
Hi there, I am very new to this and I am trying to figure out if it is possible to create a simple graphic equaliser in with set center frequency which can be boosted or cut. Wondering if it is possib
-
ADAU1452 Coefficient-Calculation-on-DSP Filter-Module in Sigma Studio 4.6 Parameter Update
I use the filter >filters/coeff calculations/second order/single precision/general (2nd order)< in combination with the module >basic DSP/parameter update<. I get access to many parameters (variable n
-
ADAU1463/67 no SDATA Output on Slave Channels
Hello all, i'm using an ADAU1463 as 8ch I2S Output as follows: - Serial Output Clock Domain0 is Master, SDATA_OUT0 carries 2 Signals (L/R) - Serial Outputs 1 - 3 are all set as slaves to Clock Domain0
-
ADAU1463/67 State of I2S Bus in RESET
Hey everyone, quick question about the ADAU1463/67 State of I2S-Bus-Pins in RESET Mode. I suspect the ADAU1463 is behaving similar to the ADAU1451 on the I2S-Pins, therefore the answer ( RE: DSP - ADA
-
ADAU1787 HP_CTRL line out vs headphone output (HP1_MODE, HP0_MODE settings)
I am: 1) connecting the DAC output to low impedance ear bud speakers 2) looping the DAC outputs to the ADC inputs When I switch (in real-time) between the HP_MODE line out and headphone out settings,
-
ADAU1701 power on delay control cs4272 reset pin,using Timer Control. DC conver to Pulse?
Function: ADAU1701 use self boot mode,After power on, ADAU1701 delay 0.5s and control cs4272 reset pin pull high ,. Hardware:ADAU1701 ( MP7)-->CS4272(Reset). If using Timer Control , ADAU1701 MP7 ,the
-
About ADAU1452 IC to Detect Input Signal Distortion
I want to know if the signal is distorted in the DSP after the signal is input into the ADAU1452, how can I achieve it?
-
How to map Indirect Parameter Access parameters to GUI controls?
I am learning about the Indirect Parameter Access and can't locate any documents that correlate the gui controls on schematic components to the parameters listed for indirect access. Some are obvious