EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
90 degree phase shift of the output signal with respect to the input signal
I how can I make a 90 degree phase shift of the output signal with respect to the input signal with Sigmastudio for the DSP Board ADAU1467 for a bandwidth of 80 to about 16,000Hz ? This is not possibl
-
alternative to AD8608 op amp for active filter design - ADAU1701
Hi all, I've been looking to implement an active reconstruction filter on the DAC output of my custom ADAU1701 however the op-amp recommended in the datasheet seems to be end of life and highly priced
-
ADAU1787 I2C Address different in datasheet and Eval board sample.
ADAU1787 datasheet stated that its I2C address started at 0x28. But when I am in Sigma Studio, when I connected USBi and AD1787, the pulldown only showed I2C address 0x50. The development kit schemati
-
Not able to hear output sound using NR example for ADAU1467
Hi everyone I want to use ANC feature using ADAU167 I have bought PDM mic for input. So at first I was testing with single mic and pair of headphones Here is my setup PDM mic connections CLK -> BCLK_I
-
AD1761 output attenuation
Hello everyone, thank you very much for understanding the novice Xiaobai's problem. The trouble here is to connect two DAC outputs, which are about 20db different from the frequency response character
-
Sigma Studio ignores SPI Clock setting for ADAU1452 SPI boot EEPROM causing programming check and code execution fails
updating to include the cause: Sigma Studio ignores SPI Clock setting for ADAU1452 SPI boot EEPROM. ------------------------------------------------------------------------------- Have a strange probl
-
Active Noise Cancellation
Hello guys, As part of my master's thesis, I am dealing with the topic of active noise canceling in the window area. For the thesis I would like to do an experiment to test feasibility. Which circuit
-
Adau1701 dac output passive vs active.
Hi guys, I'm not sure which type of adau1701 output I should use (Passive vs Active), what are the advantages of one over the other, not to mention the cost? When using AD8608 or another operational a
-
How to silently turn the ADAU1701 OFF?
Hello, I have a power amplifier and the ADAU1701 processor both powered from the same transformer having multiple windings. The amplifier on its own turns on and off silently but when the processor is
-
TDM8 DAC with external generator on 1452
Good afternoon. I have developed a DAC board that has TDM8 support and I can't get it to run. I also designed a 1452 board that has an oscillator that clocks the 1452 and external peripherals, so the
-
Read LevelRTA over I2C?
Hello Again, as in my former post, we want to read over I2C again. This time it is a 11 Band Level Detector RTA with outputs. As we need the RMS Levels of each Band for our graphic EQ display, we want
-
ADAU7118ACPZRL7 - IOVDD rail current drawn
HI Could you please share the operation state(IOVDD pin) current value when two PDM_CLKx pin is used. From datasheet, the current value is given for single PDM_CLX pin used. Attached below for referen
-
ADAU1451WBCPZ-RL - 1.2V Rail connected to external IC (ADAU7118ACPZRL7)
Hi, We are generated 1.2V using Vdrive pin & PNP transistor(DXTP3C60). This1.2V rail is connected to DVDD of DSP & the external IC (ADAU7118ACPZRL7 - it is also Analog device). The Beta of transistor
-
Dynamic processor specific hz ADAU1701
hey guys does anyone know how i can use eib dynamic block that only edits a specific hz number like 500hz for example Audio Signal Processors wondom hz SigmaDSP Audio Processors dynamic adau1701 Show
-
How do you implement a 4 microphone Beamformer
Hi, I am using 4 mics, 15cm between mics, do we have a 4 mic beamforming function or tool? Or a suggested algorithm? Edit Notes I split off this post to its own question and edited the title. (Dave T)
-
ADAU1451WBCPZ-RL - Recommendation details (Pull up / Pull down / Floating) for ADC pin not used
Hi, Could you please share the Recommendation details (Pull up / Pull down / Floating) for ADC pin when it is not used in the ADAU1451WBCPZ-RL DSP Please provide the information as soon as possible. T
-
Can I directly program ADAU1761 with I2C control port?
Hi, I'm trying to use the ADAU1761 as DAC/ADC and interface it with a FPGA. Since I'm building my own board, can I just directly program the CODEC with the I2C port to connect the serial port data to
-
Sigma Studio REV 4.6 Completion problem in using ADAU1467.
I used Sigma Studio REV 4.5 for application contain DSP ADAU1467 and compile my application. I got the signal out put as I expected. I update Sigma Studio to REV 4.6 update the USBi driver and compile
-
ADAU1451WBCPZ - Unconnected IO from die to IC pin
Hi, Could you please confirm that whether the DSP(ADAU1451WBCPZ) has unconnected I/O which is physically on the die but not bonded to pins. Please provide the information as soon as possible. Thanks i
-
Filter Precision
Dear Team , Edit Notes Edited [edited by: Hermione at 10:08 PM (GMT -4) on 29 Mar 2022]
-
ADAU1467 External control single slew volume control slew rates
What are the slew rates for this block please? I've found a thread on the similar device on the ADAU145x, but that seems to have values from 0.....41 whereas on the 1467 it's 0....15. Audio Signal Pro
-
Change Filter Boost parameter via I2C commands
I have a parametric EQ Block with 3 Biquad Filters: Now I want to change Boost via I2C Command to let's say 15 (from the 10 above). Later this should happen via I2C write command from MCU. so now I ge
-
Changing DC input entry value from MCU (ADAU1451)
Hi, I am new to using DSP, so sorry if my terms are not correct. I can not get a selectable index filter two work, when running the DSP program from the MCU. When I run the DSP program through the deb
-
How to read multiple parameters with the same name using SigmaStudioServer API?
I am using the Sigma Studio COM interface with Python to read and write parameter values. I have two NLMS filters in the schematic. Both NLMS1 and NLMS2 have the same 'coeff' param name, but at differ
-
Cannot connect symbols like phase inverter or level indicator
Hi I don't know what I am doing wrong. I would like to connect a phase inverter between the filter and the dac, but I can't. Same problem with the level indicator. Any help/hint would be highly apprec