EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
ADAU1772 Limitor activation through MP5 pin configured as "force limitor compression"
Dear Dave, I am analyzing the level of the signal through dbreg0 with microcontroller and try to activate the limitor through MP5 configured as limitor compression pin. it states in datasheet that , "
-
Before Annual Leave
Dear Team , I hope two of my queries below get answered before the annual shutdown. Please consider my questions very important and crucial 1. i am trying to understand the Slew timing of the Modules
-
Limiter/compressor algorithm - How to calculate registers value based on threshold/ratio/knee
Hi, We are use ADAU1452 DSP now, we would like to send it limiter/compressor data over MCU, there are some of information shows in here but it is incomplete. Could you please send me algorithm to calc
-
Sigma studio program crash
When I open dspproj file with my PC, Sigmastudio program just turns off without any error message. But, when I open the file with the other PC it works fine.
-
Automatic EQ Overflow?
Any tips on why I am getting overflow errors any time I try to load an impulse file in the automatic EQ block? The DSP is ADAU1452. The file was recorded at 48KHz and exported from ARTA as an MLSSA AS
-
complex signals over usb
hello i would like to ask how to transmit a complex signal exp^{i*omega*t}, i=sqrt(-1), over usb. thanks very much.
-
Question about the EQ slew in 1452
Hi, I notice the EQ slew function from wiki, Current Coefficient = Current Coeffcient * a + Target Coeffcient * (1-a) . I want to use the EQ slew in my program running on SHARC DSP to avoid the click
-
dspproj file will not open
Hi, I was happily editing a sigma studio project when I wanted to make some more dramatic changes, so I saved the project as a new project, I then closed the project. Now when I try to open either pro
-
Using an NLMS filter for background tones/beeps
Hi, We have an application where we have a beep/tone in our audio input that we would like to remove (using ADAU1452). Currently we are a notch filter to do this with good results. Unfortunately we ra
-
No FFT in sigma studio
Hi. I am using SigmaStudio 4.6 and its doesnt have fft for any of supported IC, wich version of Sigma studio supports FFT?
-
ADAU1787 - NLMS initial coefficients
Hi! I was trying to setup an NLMS filter in sigma studio on the ADAU1787 Eval board. I noticed that there is no way to set an initial coefficients in the NLMS block. Is it possible to initial the proc
-
No output from ADAU1761
My goal is to get ADAU1761 working with Teensy 4.1 Audio library. I have an ADAU1761 on a custom board designed based on eval board but without the clock generator. I'm programming it from the microco
-
Empty SPI Command column of Capture Window of SigmaStudio 4.6
Hi Team, Please help. The "SPI Command" column of the "Capture Window" in my SigmaStudio 4.6 has empty content. Please let me know how to set this column up. regards, ping sigmastudio
-
ADAU1701 STM32
Hello. I want to use ADAU1701 DSP with STM32 processor. I want to read and use features such as sound on/off, increase and decrease over the processor. Is there a source code for this? Should I use th
-
ADAU1701 audio ADC DC offset
Hi ! We are using both audio ADCs of the adau1701. The DSP program is a simple mux allowing us to use either the analog or serial inputs of the DSP (see picture). We are using DIG0 and DIG1 to send bo
-
SigmaStudio design that implements IF..THEN..ELSE like software clause
Hi Team, Please help. How do I implement a software like "IF..THEN..ELSE" switch clause in SigmaStudio design? For example, a "Mute" cell will be turn ON if GPIO MP7 input is in RAISE condition, while
-
SigmaStudio for ADAU1452 "Mute" cell of Volume Controls category vs. "Parameter Update" cell of Basic DSP category
Hi Team, Is there a way to update the parameter(s) in a specific cell, like those check box (on/off ?) in "Mute" cell and "Sine Tone" cell? Are these updates done by the "Parameter Update" cell of Bas
-
Reading a parameter by name from SigmaStudio in MATLAB.
I am able to write parameter values to the hardware in MATLAB by running a script defined as follows, for example: 'ss.ObjectSetProperties("setControlValue","SDSP-myproject.Compressor",0,0,"Threshold"
-
SigmaStudio Tree ToolBox: No Slew, Clickless HW Slew, Clickless SW Slew in many categories
Hi Team, I am using SigmaStudio 4.6 for ADAU1452. In the Tree ToolBox window, there are 1) No Slew 2) Clickless HW Slew 3) Clickless SW Slew three selections appear in some algorithm categories. For e
-
ADAU1451/2/equivalent: Ridiculous leadtimes, preventing adoption
We've been working on a new design that uses the ADAU1451. ADI is showing leadtimes to **2024** now on all of these and equivalents (1452, etc). That's absolutely absurd. Some of the distributors prom
-
ADAU1787 - another slow to fast interpolator issue.
So I want to run the FDSP at 768KHz for best ANC response, but need to run the SDSP fairly slow as it's got lots of sums to do: as 32KHz still isn't available as an option on the Fint input, I'm havin
-
SigmaStudio v4.6 ADAU1452 Interface Read cell & Interface Write cell
Hi Team, I am using SigmaStudio v4.6 for ADAU1452. My product configures MP7 GPIO as input. The "Interface Read" and "Interface Write" cells in the "Toolbox --> Inputs And Outputs" category, says "The
-
ADAU1466 with Raspberry Pi I2S
I have ADAU1466 board with external ADC/DAC converters based on PCM1802/PCM5102. Raspberry Pi used for control adau via i2c. But - I found some solutions for work with audio on raspberry pi via i2s (f
-
EVAL-ADAU1787Z USB Communication Failure Error
Hi, Dear ADI Team I am currently developing using EVAL-ADAU1787Z evaluation board. I was following the User Guide to make a simple route for testing. The problem is that when I press Link Compile Down
-
Volume Control by both Rotary Encoder & Microcontroller - ADAU1467
Hi I have a working prototype with several rotary encoders controlling the volume of various inputs. I want add remote control of these using a microcontroller, but I've now realised that there doesn'