EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
Audio Signal Detection in ADAU1772
Dear All, We are using ADAU 1772 model codec in our hardware design, controlling it via I2C bus through ESP32 processor. i would appreciate if you can help me on how i can detect the presence of the s
-
Can I use external SPI delay in 4 outputs in ADAU1452?
Hi, I need large delay which is out range of 1452, so I think I must use external SPI delay. What I wonder is if I can use one SPI RAM chip to make 4 outputs delay lines, every output use different ad
-
ADAU1467 Ext vol + AUXADC input= -87Db max
Hi! In a project with a potentiometer connected to the AUXADC input, I have an adjustment on the middle pin 0-3.3V. But why is the adjustment range in SigmaStudio limited to -96 dB...-87 Db? Audio Sig
-
Arduino safe load write - need help
\Hello, I'm very inexperienced with code but I'm trying to get my arduino to make a safe load write to the ADAU1452. I made a simple Sigma Studio project that has a volume control at address 0x0019 an
-
SigmaStudio ADAU1787 exported .dat file delay command
I exported a register only (no FDSP, no SDSP) project. The TX .dat file has the following two entries. A delay after applying power 0x00, 0x00, /* (6) IC 1.Power En Delay */ 0x00, 0x23, Where is this
-
ADAU1787 exported .dat files - filter out registers set to default
I have a project with register settings only, for now. No FDSP nor SDSP. There are a lot of registers and most remain at their default settings. Is there a way to make the exported .dat files only con
-
ADAU1701 losing PLL Lock
We have had multiple product failures from the field which are due to the ADAU1701 failing to start or maintain PLL lock. This results in static noise being outputting on the DAC. We have faced many i
-
SigmaStudio ADAU1787 register window - be nice to see register hex values as you change settings
As I change bit fields graphically in the register window, it would be useful to see the resultant hex values. Does that exist? Can it be added in a future version? In my case, I am porting code into
-
ADAU1467 EVAL BOARD I2C CONNECTION
I got EVAL-ADAU1467Z REV B board recently. I have couple of problems: 1- I need circuit schematics of this board. 2- I 'm able to load and run ADAU1467 by MCU via SPI connection. it seems analog outpu
-
Need help for ASRC lock noise and GPIO output
Hi my design has 5 input channels to ASRC and I figure out that sometimes noise coming out when ASRC is locking and I searched the answers to solve this problem and I found the only way out but someti
-
ADAU1452 SPDIF Out Bitrate
Hi Is there any possibility on the ADAU1452 to use a sample rate other than the system sampling rate for the SPDIF ouput? For example can I use 192kHz as system sampling rate and set the SPDIF sample
-
Sigma Studio - how to add Readbacks?
Hi there simple question - where do i find the Readback blocks in Sigma Studio? I want to view the value of ADC inputs but I cannot find Readback blocks anywhere in the left hand menu tree? I am using
-
A Spatializer for Monaural Audio
ADI's SuperPhat Spatializer works well with stereo program material and is especially useful with headphones. It doesn't do much, however, for monaural audio fed to both its inputs. Here's a way to ge
-
ADAU1701
Hi,everyone. I want to read the real data from one point of the Design. As for this question, I use a MCU like Stm32 which is to communciate with ADAU1701 by SPI . Simply ,I design a Lock in amplifier
-
eval-adau1467Z rev. B documentation
Hi there, Have just received an EVAL-ADAU1467Z board which is at Rev. B and seems quite a lot different to the available documenation UG-1134 Rev. 0. Is there any later documenation please? Regards, F
-
Read pulse count from a MP line in SigmaStudio v4.6 for ADAU1452
Hi Support, We are using ADAU1452 and SigmaStudio v4.6. Which algorithms are needed in order to read an input pulse counts from a MP line? regards, ping Audio Signal Processors adau1452 adau1452 sigma
-
Output pulse with count parameter through a MP line in StudioSigma v4.6 for ADAU1452
Hi Support, We are using ADAU1452 and SigmaStudio v4.6. Which algorithms are needed in order to create a design that can output pulses with count as a parameter? Can the pulse type be defined? regards
-
Is there SigmaDSP AFC Algorithm?
Hello, Is there SigmaDSP AFC(acoustic feedback cancell)Algorithm? Or how to build a system to howling suppression? 1.I have given up ADI's pitch transposer,it works not very well(Frequency shifting).
-
ADAU1452 nLMS coefficients write to FIR filter
I am using a nLMS filter to learn a simple but varying response and I want to apply the learned response to a parallel path. Essentially I want to apply the learned path coefficients to a parallel FIR
-
Need help with I2C register configuration on Master Boot
Hi, I am using the master port of the ADAU1452 in I2C master mode (i.e MP0 is pulled down low, so it doesn't boot up into the default SPI master mode). I am able to successfully see the traffic, but I
-
How/What to load SigmaStudio compiled data into ADAU1452 from an MCU?
Hi Support, We are using ADAU1452 and SigmaStudio v4.6. The SPI Slave Control Port of the ADAU1452 in our design is connected to an SPI Master port of an MCU. Our design includes a big flash storage.
-
USBi arm64 driver ?
Hi, You are probably aware of the rise of ARM based computers such as some Microsoft Surface devices or M1 Macs running "Windows on ARM" as a virtual machine. Sigma Studio will run on these devices vi
-
License fee of AcousticEchoCancellation and NoiseReduction algorithms for ADAU1452-150
Hi Support, I am using ADAU1452-150 and/or ADAU1452 and SigmaStudio v4.6. Please let me know how to license AcousticEchoCancellation and NoiseReduction algorithms. regards, ping Audio Signal Processor
-
Questions for ADAU1787 configurations for Audio Serial Data communication
Dears, My goal is to complete the following signal flow with external BCLK, LRCK @ 48KHz (1) ADAU1787 ADC => I2S_Data_Output (2) I2S_Data_Input => ADAU1787 DAC In order to check the configurations, I
-
1787 at 768 kHz?
Hello: I set up a 1787 eval board SDSP and FDSP to work together at 48 kHz and found I could pass audio through it successfully. I then tried to set up the same board with another project (attached) t