EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
SigmaStudio development
Is SigmaStudio still in active development with future releases planned? I've noticed a bunch of planned features over the last few years' worth of questions that haven't been implemented yet, but 4.6
-
Setting and getting the value of a mono Switch via the Sigma Studio to Matlab activeX interface
Hi everybody, I'm new here and really need some help. I have an EVAL-ADDAU1466Z eval board and a little DSP program running on the 1466Z. It works fine. Now, from what I read, there is a possibility t
-
How Do I View The FFT Output Data In Sigma Studio (ADAU1452)?
I am using the ADAU1452 evaluation board and I'm trying to use the FFT block. Can anyone give me a suggestion of how I can view the FFT data in Sigma Studio? I can put the FFT block in my schematic an
-
Reduce the size of DM0 and DM1 download packets ... and Checksum calculation
I have checked the Reduce the size of DM0 and DM1 download packets by removing zero initializations option in Sigma Studio 4.6 for ADAU1452 and I have some questions: 1 : Now I have four DM buffers in
-
Connect microphone and headphones to ADUA1467Z
Hi! I'm having some problems with connecting my microphone and headphones to an ADAU1467Z. I'm trying to connect the microphone through input jack 1, IN1, with a TRS 3.5 mm and then the headphones are
-
ADAU1701 duplicate power pins
Hello All, I am currently working on the PCB layout for a board that includes an ADAU1701. However, I am a little confused with the power pins. The chip has a pair of power and ground pins in each cor
-
Chime Freq-Gain Frequency Increment
Hello, I have been attempting to use the Chime Freq-Gain block in DSP program, however, I am not exactly sure what to write to the DSP for the frequency envelope to function as intended. I have seen a
-
DMIC Example - ADI1787z
Hello, I am having trouble similar to this post: https://ez.analog.com/dsp/sigmadsp/f/q-a/112923/dmic-setup-on-eval-aday1787z-board/336929#336929 I want to connect DMIC0/1 through the fast DSP out to
-
selecting only the positive-going zero crossings of a sine wave
Hi, I am using an ADAU1452 and want to generate a "gated" sine wave as a test signal. That is 'A' cycles of sine wave then 'B' cycles of silence. I can use the "Value Cross Detection" block from Basic
-
Hardware Slew Sigma DSP
Dear Team , I have a question with regard to the Volume Control HW Slew vs Volume Control SW Slew . The data sheet mentions that the HW version uses fewer instructions per cycle however ,the compiler
-
ADAU1452: Init Selfboot by MCU
Hi, I have the following situation: I have an ADAU1452 fully booted from an EEPROM in self boot mode. Now after a while I want my MCU to send a command to the ADAU1452 DSP that inits a new self boot.
-
Stereocoder 38Khz multiplex not working on adau1451
Hi, I build de stereocoder in adau1451 from the schema in adau1701. It works accept the 38Khz won't come out. Did try to change the clock settings and sample rate but solves nothing. Stereocoder-1701.
-
ADAU1787 Fast DSP EQ coefficient control via MATLAB
Hello, I am controlling an ADAU1787 FDSP core via SigmaStudio, from MATLAB commands and generally this works well. Parameters such as Boost can be controlled as follows, if I set the type to be parame
-
LRCLK in TDM8
Hi, I have a device connected to an ADAU1466 that transmits audio with a kind of TDM8 where the period of the LRCLK signal has a duration of 2 channels instead of 8. In practice it is an I2S where in
-
ADAU1701 response to digital pulse time
For an active loudspeaker project, I am trying to control a WISA receiver with an ADAU1701. For now, I am using an Arduino to mimic the WISA's pulses and behavior. In the end I will have to read a 26u
-
ADAU1466 - Envelope Follower with different time constants as attack and decay
Hello community, 1) I want to implement a clipper that follows the envelope of my audio signal with different time constants during the attack and decay of the waveform. lN,c is the nominal clipping l
-
Question before Purchasing EVAL-ADAU1466Z
Hello, I am considering purchasing this evaluation board for my team's senior design project but I had a concern about it's sample rate limitation. Our project requires a 192kHz sample rate in order t
-
Are these DSP's best for this kind of Active noise cancellation for rigid barriers?
Me and my partner have been looking at many of your DSP's Eval boards to use for our Active Noise Cancelation (ANC) Senior design project. We are trying to stay under $250, just for the DSP Eval board
-
.dspproj file EULA
Perhaps not an engineering-focused question, but our legal team is wondering about the license agreement to transfer of .dspproj files generated from SigmaStudio between different companies. The Sigma
-
How to set EVAL-ADAU1466Z EVAL BOARD sample rate to 192Khz?
I have modified EVAL-ADAU1466Z EVAL BOARD to control AD1938 via Sigma Studio Version 4.6. and set sample rate to 96Khz and got sinewave(40000Kz) succcesfully. When I had changed to 192Khz it did not w
-
Crossover Parameters Missing?
I tried to put a crossover into the schematic but the icon was greyed out. The crossover icon was was there but you could not access the parameters but double clicking. I am using V4.6 and 1701.
-
Integration of ADAU1466 and ADAU1777 for Feed Forward Active Noise Cancellation ANC
Hello, After several hours of searching through these forums for solutions for implementing a feed forward ANC system I have come to a few conclusions. 1. ANC Algorithm can be implemented using SigmaS
-
How to verify parameter update from MCU in Sigma DSP ADAU1452.
Dear Team, I am updating Sigma studio cell parameters from MCU. And need to check this parameter update in DSP. For Example, If I have changed the Volume gain from -6dB to -2dB from MCU. This gain par
-
SPI configuration in Sigma DSP
Dear Team, We are using same SPI line for both communication of 'MCU to DSP' and 'PC(USBi) to DSP'. After the SPI communication of MCU->DSP (i.e After Booting) , we need to switch for communication am
-
ADAU1466 SDATA_OUTx Clock Output
I am trying to line up clocks and data on an SDATA_OUTx port that matches incoming clocks on LRCLK_IN/OUT0 and BCLK_IN/OUT0. My understanding is when any SDATA_OUTx port needs to be a BCLK and LRCLK m