EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (5719 topics).
5719 topics · 27691 messages
-
[SHARING] Filter coeficents online calculator with sample code for C++, C#, MicroPython and Arduino Sketch
Hi guys, im sharing an online filter calculator, that can generate sample/example codes for C++, C#, MicroPython and Arduino Sketch, also you can check your own code calculations results This calculat
-
ADAU145x datasheet ASRC group delay calculation
On page 81 of Rev.D of the ADAU145c datasheet there are calculations for the ASRC group delay : The same equations appear in the AD1895 datasheet, so surely they must be correct. In the first equation
-
Sigma DSP data streaming possible?
Hello, for a new project I would like to record an analog signal from a microphone for a certain time and transfer this data to the microcontroller. To start a measurement I want to start the "data st
-
ADAU1772 Codec got Reset at high volume if headset plug/unplug
Hi, Used ADAU1772 codec on our board, using in Ain0/1 (Stereo input J2 jack) and HPOUTLP/HPOUTRP (Stereo output J8 jack), simple pass-through audio (DSP is not used). Observed if plug/unplug headset a
-
16-Bit I2S data on ADAU145x/146x
Hi, I've tried to use the Serial Port for a 2x 16-Bit interface to another chip. The serial port is a slave configuration. But when I set the dropdown list to "2 channels / 16 bit/channel" the graphic
-
Connect several PCM1808 to ADAU1701
Hello everyone, I'm trying to connect several PCM1808 AD converters to an ADAU1701. Can anybody tell me how the connections have to be made? And can the MCLK of the PCM1808 directly connected to the A
-
ADAU1772 Sigma TCP
HI, will there ever be a TCPIP connection driver for the ADAU1772/1777? Can there be a generic TCP driver for all SIGMA DSP devices? kind regards huegene adau1772 Integrated/Special Purpose A/D Conver
-
ADAU1777/ADAU1772/ADA1372 initialization when an external oscillator is used
I am confirming how to start and initialize the ADAU1777, ADAU1772 or ADA1372 when an external oscillator is used. In each data sheet, I can find following description. Regarding it, please let me ask
-
ADAU1701 selfboot
Dear colleagues, is it possible in principle to use two ADAU1701 in self-boot mode from the same single EPROM? Is it possible to use a single project to load the circuits into both chips. The audio si
-
[ADAU1451] I2S microphone configuration with AEC algorithm
Hello all, I am not experienced in audio signal processing and I have never worked with SigamaStudio or any Analog Devices' DSP, therefore I am having some difficulties. I am using the HiFiBerry DAC+
-
ADAU1701 basic clock issue/question
I've designed by own board based around the ADAU1701. I've followed the datasheet as best as I could down to a T and used a tight layout with best practices. I seem to be stuck at the most basic issue
-
ADAU Fast & Sigma clock frequencies
Now then. I need to run the Fast core at 768KHz for reasons of latency, but can run the S core at 24 or 32KHz (48KHz won't work as not enough cycles available). The problem I'm having is that the FInt
-
SigmaStudio ADAU1787 differences between Capture data and I2C scanner results issue
Hello I have noticed differences between the data displayed in the Capture window and the real I2C data captured with external scanner. As you can see on the attached screenshots, differences are rela
-
Filter at low frequency having near no effect on adau1701
Hi, I've been trying to notch out a frequency in the 40-60 range, specifically 56-63.5 by using a peaking filter and it's giving me unusual results, I think because there's a limit on the bandwidth th
-
ADAU1467 Eval Board - Sigma Studio non-responsive
Hi there, I've just upgraded from our ADAU1452 evaluation board for an ADAU1467 evaluation board. I've just setup a simple Schematic, set "Compile -> Link -> Download" which was successful and the sta
-
Sigma Studio Medium Size EQ control
Hello I can notice in the capture window of the Sigma Studio that coefficients for the Medium Size EQ are send twice (please see the attached screenshot). What's the reason of that ? Is it a kind of a
-
Sigma Studio Medium Size EQ calculations
Hello I'm lookig for equations used to calculate coefficients for the Medium Size EQ component of the SigmaStudio: https://wiki.analog.com/resources/tools-software/sigmastudio/toolbox/Filters/MediumSi
-
ADAU1361 differential amplifier not working, no internal bias on input pins - damaged part, or just misconfigured?
I'm bringing up a new design that utilizes an ADAU1361, and I've run into a bit of a snag that I'm hoping is just due to a misconfiguration of the device, but which I fear is actually evidence that th
-
Difference between NxM mixer and signal add
Hi, I find a question that when I use signal add module, two same inputs sine waves in, then the output from signal add is easily clip or distort. I know the output is out of my DAC's range which case
-
LR Balance switching between 3 values and can you apply logic to check the amplitude of specific frequencies?
Hi, Just Background as to what Im using the adau1701 for, feel free to skip through. I just got my hands into using Sigmadsp Studio a few days ago and while it has it's quirks and I wasn't so pleased
-
Echo cancellation on megaphone using ADAU1761
I am developing a megaphone using ADAU1761. The structure is as in the attached image. However, when the output level is raised, the howling is severe. I've searched various QnA related to echo cancel
-
ADAU1979 behavior under loss of MCLK
Is anyone aware of any abnormal behavior in the ADAU1979 if MCLK is lost (but BCLK and LRCLK keep running)?
-
ADAU1467: SPI Interface, ESP32 + USBi
Hi All, I want to have the ability to use both USBi and ESP32 on the same SPI lanes, so therefor i have directly connected ESP32 too ADAU1467, and the ADAU1467 is placed on a MediaWorks board, here th
-
ADAU1467: SDATA IO several inputs on one port
Hi All, I have recently made a board that should have the ability to handle 16 inputs in total, on serial port 0 i have one PCM4202 directly attached, and three more modules connected through IO 2,4,6
-
A2B network - connect slave node to a SigmaDSP
Hi all, I want to design an A2B network which is controlled by a SC584 dsp and one of the slave nodes has a microphone which need to go through some processing in a SigmaDSP (ADAU14XX). The processing